Toolpack:Creating a Line Interface D
From TBwiki
(Difference between revisions)
(Created page with "=== '''''Applies to version(s): v2.9.''''' === {{DISPLAYTITLE:Creating a Line Interface}} Line interface is a generic term for TDM physical interfaces. TelcoBridges products s...") |
|||
| (11 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
{{DISPLAYTITLE:Creating a Line Interface}} | {{DISPLAYTITLE:Creating a Line Interface}} | ||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |rowspan="2"|This article applies to: | ||
| + | |'''Product''' | ||
| + | |'''Version''' | ||
| + | |- | ||
| + | |Tmedia | ||
| + | |2.9, 2.10, 3.0, 3.2 | ||
| + | |} | ||
| + | |||
Line interface is a generic term for TDM physical interfaces. TelcoBridges products support 3 types of physical interfaces: | Line interface is a generic term for TDM physical interfaces. TelcoBridges products support 3 types of physical interfaces: | ||
| + | |||
*[[T1,_E1,_and_J1_interfaces | T1/E1/J1 interfaces]] | *[[T1,_E1,_and_J1_interfaces | T1/E1/J1 interfaces]] | ||
*[[DS3_interfaces | DS3 interfaces]] | *[[DS3_interfaces | DS3 interfaces]] | ||
*[[SONET/SDH_interfaces | SONET/SDH interfaces]] | *[[SONET/SDH_interfaces | SONET/SDH interfaces]] | ||
| − | |||
| + | To create line interface(s): | ||
1- Select '''TDM Line Interfaces''' from the navigation panel | 1- Select '''TDM Line Interfaces''' from the navigation panel | ||
| Line 14: | Line 24: | ||
| − | 2- | + | 2- You can create one line interface at a time or multiple line interfaces in a single pass. |
| + | |||
| + | 2a- To create a single line interface, click '''Create New Line Interface'''. | ||
[[Image:CreateLineInterface_1_A.png]] | [[Image:CreateLineInterface_1_A.png]] | ||
| − | + | 2b- To create a range of line interfaces, click '''Create Multiple Line Interfaces'''. | |
| + | |||
| + | [[Image:CreateMultipleLineInterface_0_A.png]] | ||
| + | |||
| + | |||
| + | 3- Enter values for the line interface. | ||
| + | 3a- Single line interface | ||
* Enter a '''name''' for the interface | * Enter a '''name''' for the interface | ||
* Set a '''type''' for the interface | * Set a '''type''' for the interface | ||
| Line 28: | Line 46: | ||
[[Image:CreateLineInterface_2_A.png]] | [[Image:CreateLineInterface_2_A.png]] | ||
| + | |||
| + | |||
| + | 3b-Multiple line interfaces | ||
| + | * Set a '''type''' for the interface | ||
| + | * Enter a '''name''' for the range of interfaces. (In this example 'SeriesA' is prefixed to the name) | ||
| + | * Enter the number of line interfaces you wish to create. | ||
| + | * Set an '''index''' for the first line. | ||
| + | * Select a '''length''' and an '''encoding scheme''' | ||
| + | * Click '''Create''' | ||
| + | |||
| + | [[Image:CreateMultipleLineInterface_1_A.png]] | ||
| Line 40: | Line 69: | ||
'''Path''' | '''Path''' | ||
<pre> | <pre> | ||
| + | |||
| + | /configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name] | ||
</pre> | </pre> | ||
'''Parameters (text)''' | '''Parameters (text)''' | ||
<pre> | <pre> | ||
| + | /configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name] | ||
| + | local_index = 0 | ||
| + | name = "@[line_interface_name]" | ||
| + | type = "T1" | ||
| + | |||
| + | /configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name]/state | ||
| + | loopback_type = "None" | ||
| + | tx_state = "TX on" | ||
| + | |||
| + | /configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name]/t1_parameters | ||
| + | encoding = "B8ZS" | ||
| + | length = "Short" | ||
| + | signal_level = "2" | ||
| + | |||
</pre> | </pre> | ||
| + | |||
'''Parameters (json)''' | '''Parameters (json)''' | ||
<pre> | <pre> | ||
| + | |||
| + | { | ||
| + | "local_index" : 0, | ||
| + | "name" : "LI_T1_00", | ||
| + | "state" : { | ||
| + | "loopback_type" : "None", | ||
| + | "tx_state" : "TX on" | ||
| + | }, | ||
| + | "t1_parameters" : { | ||
| + | "encoding" : "B8ZS", | ||
| + | "length" : "Short", | ||
| + | "signal_level" : "2" | ||
| + | }, | ||
| + | "type" : "T1", | ||
| + | "line_services" : { | ||
| + | } | ||
| + | } | ||
| + | |||
</pre> | </pre> | ||
</div> | </div> | ||
| − | |||
Latest revision as of 15:21, 24 November 2020
| This article applies to: | Product | Version |
| Tmedia | 2.9, 2.10, 3.0, 3.2 |
Line interface is a generic term for TDM physical interfaces. TelcoBridges products support 3 types of physical interfaces:
To create line interface(s):
1- Select TDM Line Interfaces from the navigation panel
2- You can create one line interface at a time or multiple line interfaces in a single pass.
2a- To create a single line interface, click Create New Line Interface.
2b- To create a range of line interfaces, click Create Multiple Line Interfaces.
3- Enter values for the line interface.
3a- Single line interface
- Enter a name for the interface
- Set a type for the interface
- Set a local index for the line
- Select a length and an encoding scheme
- Click Create
3b-Multiple line interfaces
- Set a type for the interface
- Enter a name for the range of interfaces. (In this example 'SeriesA' is prefixed to the name)
- Enter the number of line interfaces you wish to create.
- Set an index for the first line.
- Select a length and an encoding scheme
- Click Create
4- Verify that the "Line interface was successfully created" message is displayed
Path
/configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name]
Parameters (text)
/configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name] local_index = 0 name = "@[line_interface_name]" type = "T1" /configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name]/state loopback_type = "None" tx_state = "TX on" /configurations/@[configuration_name]/hardware_units/@[hardware_name]/tdm_line_interfaces/@[line_interface_name]/t1_parameters encoding = "B8ZS" length = "Short" signal_level = "2"
Parameters (json)
{
"local_index" : 0,
"name" : "LI_T1_00",
"state" : {
"loopback_type" : "None",
"tx_state" : "TX on"
},
"t1_parameters" : {
"encoding" : "B8ZS",
"length" : "Short",
"signal_level" : "2"
},
"type" : "T1",
"line_services" : {
}
}
List of Parameters
Advanced Parameters
