Toolpack:Configuring VoIP Interfaces E
From TBwiki
(Difference between revisions)
(First version) |
|||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
{{DISPLAYTITLE:Configuring VoIP Interfaces}} | {{DISPLAYTITLE:Configuring VoIP Interfaces}} | ||
| + | |||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |rowspan="2"|This article applies to: | ||
| + | |'''Product''' | ||
| + | |'''Version''' | ||
| + | |- | ||
| + | |SBC | ||
| + | |3.0, 3.1 | ||
| + | |} | ||
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following: | ||
| Line 14: | Line 23: | ||
1. Select '''IP Interfaces''' from the navigation panel: | 1. Select '''IP Interfaces''' from the navigation panel: | ||
| − | [[ | + | [[Image:CreateIpInterface_Tsbc_1.png]] |
<br> 2. Click the '''IP Interfaces''' tab. | <br> 2. Click the '''IP Interfaces''' tab. | ||
| Line 32: | Line 41: | ||
*Click '''Save''' | *Click '''Save''' | ||
| − | '''Note:''' | + | '''Note:''' IP addresses using different virtual ports must be on different subnets. <br> |
| − | [[ | + | [[Image:CreateIpInterface_Tsbc_1a.png]] |
<br> | <br> | ||
| Line 40: | Line 49: | ||
4. The changes are displayed in the IP interfaces information panel: | 4. The changes are displayed in the IP interfaces information panel: | ||
| − | [[ | + | [[Image:CreateIpInterface_Tsbc_1b.png]] |
| Line 46: | Line 55: | ||
5. Activate the configuration | 5. Activate the configuration | ||
| + | *Select '''System''' from the navigation panel. | ||
| + | *Click '''Activate''' | ||
| − | |||
| − | + | 6. You must reboot the adapters only if you are using the vlan from ports 3441 to 3450. | |
| − | + | *Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter | |
| − | 6. | + | |
| − | + | ||
| − | Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter | + | |
It will take about 1.5 minutes to restart the unit. | It will take about 1.5 minutes to restart the unit. | ||
| − | |||
| − | |||
| − | |||
| − | |||
== List of Parameters == | == List of Parameters == | ||
Latest revision as of 08:36, 15 December 2020
| This article applies to: | Product | Version |
| SBC | 3.0, 3.1 |
The IP interface of the VoIP0 and VoIP1 ports can be configured by setting the following:
- IP Address
- Netmask
- Gateway
To configure a VoIP0 or VoIP1 port
1. Select IP Interfaces from the navigation panel:
2. Click the IP Interfaces tab.
- Click Create New IP Interface
3. Configure the IP port:
- Enter a name for the interface
- Select a service to use for the IP inteface
- Select a Virtual port from which IP packets will exit.
- Indicate whether or not to use DHCP to automatically get an IP address for this port. (selecting this option removes the need to enter and IP address, Netmask, and Gateway)
- Enter an IP address
- Enter a Netmask
- Enter a gateway address
- Click Save
Note: IP addresses using different virtual ports must be on different subnets.
4. The changes are displayed in the IP interfaces information panel:
5. Activate the configuration
- Select System from the navigation panel.
- Click Activate
6. You must reboot the adapters only if you are using the vlan from ports 3441 to 3450.
- Status -> Adapters -> Click on the adapter Serial Number -> Reboot adapter
It will take about 1.5 minutes to restart the unit.
