Toolpack:Configuring Vlan SBC A
From TBwiki
(Difference between revisions)
(First version of the page) |
|||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
{{DISPLAYTITLE:Configuring a VLAN}} | {{DISPLAYTITLE:Configuring a VLAN}} | ||
| + | |||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | |rowspan="2"|This article applies to: | ||
| + | |'''Product''' | ||
| + | |'''Version''' | ||
| + | |- | ||
| + | |SBC | ||
| + | |3.1 | ||
| + | |} | ||
After you create a virtual port, you must create a new VLAN. | After you create a virtual port, you must create a new VLAN. | ||
| Line 10: | Line 19: | ||
1. Select '''IP Interfaces''' from the navigation panel | 1. Select '''IP Interfaces''' from the navigation panel | ||
| − | [[ | + | [[Image:Create Vlan Interface_Tsbc_0.png]] <br><br> |
2. Click the '''Virtual Ports''' tab. | 2. Click the '''Virtual Ports''' tab. | ||
*Select a Virtual Port | *Select a Virtual Port | ||
| − | [[ | + | [[Image:Create Vlan Interface_Tsbc_1.png]]<br><br> |
| − | + | 3. Create a VLAN that uses this virtual port | |
*Click '''Create new Host VLAN''' | *Click '''Create new Host VLAN''' | ||
| − | [[ | + | [[Image:Create Vlan Interface_Tsbc_2.png]]<br><br> |
| − | + | ||
| − | + | ||
| + | 4. Configure the new VLAN | ||
| + | ====Important Note==== | ||
| + | Vlans can be configured on the SBC in these cases:<br> | ||
| + | * Baremetal installation | ||
| + | * VMware installation with Passthrough or SR-IOV network interfaces | ||
| + | * VMware installation with a network interface using vlan ID 4095 | ||
| + | <br> | ||
| + | Vlans should '''not''' be configured on the SBC in this case:<br> | ||
| + | * VMware installation with network interfaces using vlans from 1 to 4094 | ||
| + | In this case, all interfaces on the SBC should be configured as untagged. Vlans are configured in the VMware port Groups. <br> | ||
| + | Please check here: [[TSBC-SW:Cloud:VMware_Adding_Network_Intefaces_A|How to add VMware Network Interfaces]]<br> | ||
| + | <br> | ||
| + | If VLANs must be configured, follow these steps:<br> | ||
*Enter a name for the VLAN | *Enter a name for the VLAN | ||
*If the port is to be used untagged, make sure '''Untagged''' is checked. | *If the port is to be used untagged, make sure '''Untagged''' is checked. | ||
| Line 29: | Line 49: | ||
*Click '''Create''' | *Click '''Create''' | ||
| − | [[ | + | [[Image:Create Vlan Interface_Tsbc_3.png]] <br><br> |
| + | |||
| + | |||
| + | OR | ||
| + | |||
| + | |||
| + | [[Image:Create Vlan Interface_Tsbc_4.png]] <br><br> | ||
==List of Parameters== | ==List of Parameters== | ||
| Line 36: | Line 62: | ||
* [[Parameter: Untagged|Untagged]] | * [[Parameter: Untagged|Untagged]] | ||
* [[Parameter: VLAN id|VLAN id]] | * [[Parameter: VLAN id|VLAN id]] | ||
| + | * [[Parameter: Allow ICMP|Allow ICMP]] | ||
| + | * [[Parameter: Allow IP fragmentation|Allow IP fragmentation]] | ||
Latest revision as of 09:13, 15 December 2020
| This article applies to: | Product | Version |
| SBC | 3.1 |
After you create a virtual port, you must create a new VLAN.
To configure a VLAN
1. Select IP Interfaces from the navigation panel
2. Click the Virtual Ports tab.
- Select a Virtual Port
3. Create a VLAN that uses this virtual port
- Click Create new Host VLAN
4. Configure the new VLAN
Important Note
Vlans can be configured on the SBC in these cases:
- Baremetal installation
- VMware installation with Passthrough or SR-IOV network interfaces
- VMware installation with a network interface using vlan ID 4095
Vlans should not be configured on the SBC in this case:
- VMware installation with network interfaces using vlans from 1 to 4094
In this case, all interfaces on the SBC should be configured as untagged. Vlans are configured in the VMware port Groups.
Please check here: How to add VMware Network Interfaces
If VLANs must be configured, follow these steps:
- Enter a name for the VLAN
- If the port is to be used untagged, make sure Untagged is checked.
- If the port is to be used with a 802.1Q tag, uncheck Untagged and enter a VLAN ID.
- Click Create
OR
