MTP3:Userpart Configuration
From TBwiki
(Difference between revisions)
(initial content) |
|||
| (7 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
| − | *'MTP3 user part unique ID' is used to configure identical [[MTP3 Layer|MTP3]] userparts in each MTP3 module and to connect [[ISUP]] networks. | + | *'''MTP3 user part unique ID''' is used to configure identical [[MTP3 Layer|MTP3]] userparts in each MTP3 module and to connect [[ISUP]] networks. |
| − | *The 'Connection mode' parameter specifies the different modes of connection for an MTP3 userpart. The following values are allowed: | + | |
| + | ---- | ||
| + | |||
| + | |||
| + | *The '''Connection mode''' parameter specifies the different modes of connection for an MTP3 userpart. The following values are allowed: | ||
| Line 26: | Line 29: | ||
| − | *The 'Sub-service | + | ---- |
| + | |||
| + | |||
| + | *The '''Sub-service field''' specifies the type of network. If validation is activated in the general MTP3 configuration, all userpart messages will be compared to this sub-service field type. All non-matching messages will be discarded. The following values are allowed: | ||
| Line 43: | Line 49: | ||
'''NOTE:''' For all national networks (including TTC and NTT), the 'Sub-service' field is configured with 'National'. For international networks, the 'Sub-service' field is configured with 'International'. | '''NOTE:''' For all national networks (including TTC and NTT), the 'Sub-service' field is configured with 'National'. For international networks, the 'Sub-service' field is configured with 'International'. | ||
| + | |||
'''NOTE:''' For international networks you must have the same values for Prior Message Queue Length 1 to Prior Message Queue Length 1 in a MTP3 Link Configuration. | '''NOTE:''' For international networks you must have the same values for Prior Message Queue Length 1 to Prior Message Queue Length 1 in a MTP3 Link Configuration. | ||
| − | *The 'Link type' field specifies the MTP3 protocol variant required to provide service to the userpart connected through this upper Service Access Point (SAP). The following values are allowed: | + | ---- |
| + | |||
| + | |||
| + | *The '''Link type''' field specifies the MTP3 protocol variant required to provide service to the userpart connected through this upper Service Access Point (SAP). The following values are allowed: | ||
| Line 68: | Line 78: | ||
| − | *The 'DPC length' field specifies the length of the DPC for messages communicated through this SAP. For allowable values, see [[MTP2:Destination Point Code]]. | + | ---- |
| − | *The | + | |
| + | |||
| + | *The '''DPC length''' field specifies the length of the DPC for messages communicated through this SAP. For allowable values, see [[MTP2:Destination Point Code]]. | ||
| + | *The '''Switch ID''' parameter specifies a value to regroup linksets and user parts together. Allowable values are from 10 to 255. | ||
| + | |||
| + | For further configuration information see [[Toolpack:Protocol_Stack_Settings_D|Protocol Stack Settings]] | ||
Latest revision as of 10:47, 28 March 2018
- MTP3 user part unique ID is used to configure identical MTP3 userparts in each MTP3 module and to connect ISUP networks.
- The Connection mode parameter specifies the different modes of connection for an MTP3 userpart. The following values are allowed:
| Connection mode | Description |
|---|---|
| SCCP | MPT3 userpart is used in conjunction with an above local SCCP layer and cannot be controlled by the host application |
| SCCP with alarms | MPT3 userpart is used in conjunction with an above local SCCP layer and cannot be controlled by the host application but the host application will receive ALARM notifications |
| ISUP | MTP3 userpart is used in conjunction with an above local ISUP layer and cannot be controlled by the host application |
| ISUP with alarms | MPT3 userpart is used in conjunction with an above local ISUP layer and cannot be controlled by the host application but the host application will receive ALARM notifications |
| Host SCCP | MTP3 userpart is used as a standalone and communicates with remote SCCP layer (host application) |
| Host TUP 5 | MTP3 userpart is used as a standalone and communicates with remote TUP layer (host application) |
| Host ISUP | MTP3 userpart is used as a standalone and communicates with remote ISUP layer (host application) |
- The Sub-service field specifies the type of network. If validation is activated in the general MTP3 configuration, all userpart messages will be compared to this sub-service field type. All non-matching messages will be discarded. The following values are allowed:
| Sub-service field | Description |
|---|---|
| International | Messages sent by the layer will concern international traffic |
| National | Messages sent by the layer will concern national traffic |
| Reserved | Reserved for national use |
NOTE: For all national networks (including TTC and NTT), the 'Sub-service' field is configured with 'National'. For international networks, the 'Sub-service' field is configured with 'International'.
NOTE: For international networks you must have the same values for Prior Message Queue Length 1 to Prior Message Queue Length 1 in a MTP3 Link Configuration.
- The Link type field specifies the MTP3 protocol variant required to provide service to the userpart connected through this upper Service Access Point (SAP). The following values are allowed:
| Link type | Description |
|---|---|
| ANSI | Used for ANSI88 and ANSI92 |
| ITU | Used for ITU88, ITU92, ITU97, Q767, SINGAPORE and ETSI |
| CHINA | Used for CHINA |
| ANSI96 | Used for ANSI96 and TELCORDIA |
| TTC | Link type not available yet |
| NTT | Link type not available yet |
- The DPC length field specifies the length of the DPC for messages communicated through this SAP. For allowable values, see MTP2:Destination Point Code.
- The Switch ID parameter specifies a value to regroup linksets and user parts together. Allowable values are from 10 to 255.
For further configuration information see Protocol Stack Settings
