FreeSBC:Cloud:VmWare Installation A

From TBwiki

(Difference between revisions)

Latest revision as of 11:19, 26 January 2021

Requirements

Minimal Cloud requirements:

Vmware ESX 5 or 6
64-bit infrastructure only
E1000 NIC emulation or VMXNET3 interfaces
One Ethernet adapter for management (mgmt0)
One or more Ethernet adapter(s) for SIP and RTP traffic according to the table below (LAN/WAN)
If you are deploying ProSBC in a 1+1 configuration, you need two (2) additional Ethernet adapters to be used as control ports (ctrl0/ctrl1).
If you are deploying ProSBC with transcoding devices, you will need four (4) additional Ethernet adapters to be used as control and transcoding ports (ctrl0/ctrl1, trans0/trans1).

Sessions	CPU	RAM	Disk Space (SSD)	Data Ethernet ports
Up to 5,000	2 to 4	4 Gb	40 Gb	1 Gbps
5,001-20,000	4 to 6	8 Gb	60 Gb	4 X 1 Gbps or 1 X 10 Gbps
20,001-26,000	6 to 8	16 Gb	80 Gb	1 X 10 Gbps

** The CPU number is based on Intel R630 with Xeon E5-2643. Double the CPUs number if yours are from a earlier generations.

More details on HW/CPU/NIC requirements can be found here: Requirements Matrix

For better performance use these settings:

CPU resource: allocation shares set to 'high'
CPU resource: reservation set to maximum and no limit (i.e. 'unlimited')
Memory resource: reserve all guest memory (all locked)
Disk: shares 'high'
Advanced CPU: Hyperthread core sharing to 'None'
Latency Sensitivity: 'High'

Getting the Image

Please go to our ProSBC Download site to get a copy of the latest SBC Image.

Installation on VmWare cloud

ProBSC VmWare Image

A virtual machine image is a single file that contains a virtual disk that has a bootable operating system installed on it. Images are used to create virtual machine instances within the cloud.

You will need to upload the latest SBC image into your VmWare before you can launch a virtual machine instance running the SBC software.

Launching an instance

Using the ESXi Web client

Using the vSphere client application

If you are installing a standalone SBC, the ProSBC or FreeSBC will need access to LAN/WAN and MGMT networks. For transcoding on TSBC-HW-TRANS, or HA pair installation, the ProSBC will also need access to CTRL0/CTRL1, and TRANS0/TRANS1 networks. In both instance launching methods above, when editing network adaptor, please take reference to ProSBC Networking for details on network requirements.
For ProSBC Transcoding and associated network setup please also see FreeSBC:Transcoding and Network Setup.

Accessing the SBC

Assigning IP address

By default, all detect network interfaces will have DHCP enabled. Thus, the server might already have an IP address assigned if the network has a DHCP server running. In such case, you can display and use it to access the web portal configuration panel.

Retrieve an IP address assigned by DHCP

 # ifconfig

If you want to assigned a static IP address or there are no DHCP on your network, you will need to configure it manually.

Use tbchangeip shell command and answered questions to changed your Ethernet interface address:

 # tbchangeip

Accessing the SBC web portal

Open a web browser to the management IP of the SBC, on port 12358. Example if your server address is 192.168.178.30, the URL would be:
http://192.168.178.30:12358

You should get to the SBC Configuration Wizard

If you do not know the IP address, you can find it from the VMware interface:

From here, you can go to Web Portal Initial Configuration Guide to continue the installation, and/or optimize your server to get the maximum out of your server.

Web Portal Initial Configuration

Click on the following link to pursue installation from the web portal: SBC Initial Configuration

@@ Line 1: / Line 1: @@
-{{DISPLAYTITLE:FreeSBC:Cloud:VmWare Installation}}
+{{DISPLAYTITLE:ProSBC/FreeSBC:Cloud:VmWare Installation}}
 == Requirements ==
 Minimal Cloud requirements:
@@ Line 7: / Line 7: @@
 * One Ethernet adapter for management (mgmt0)
 * One or more Ethernet adapter(s) for SIP and RTP traffic according to the table below (LAN/WAN)
-* If you are deploying FreeSBC with transcoding devices or in a 1+1 configuration, you will two additional Ethernet adapters to be used as control ports (ctrl0/ctrl1).
+* If you are deploying ProSBC in a 1+1 configuration, you need two (2) additional Ethernet adapters to be used as control ports (ctrl0/ctrl1).
+* If you are deploying ProSBC with transcoding devices, you will need four (4) additional Ethernet adapters to be used as control and transcoding ports (ctrl0/ctrl1, trans0/trans1).
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 14: / Line 15: @@
 ! width="100" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | CPU
 ! width="100" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | RAM
-! width="100" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Disk Space
+! width="100" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Disk Space (SSD)
 ! width="200" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Data Ethernet ports
 |-
@@ Line 20: / Line 21: @@
 Up to 5,000
 | valign="top" |
+to 4
 | valign="top" |
 Gb
@@ Line 29: / Line 30: @@
 |-
 | valign="top" |
-,000-20,000
+,001-20,000
 | valign="top" |
+to 6
 | valign="top" |
 Gb
@@ Line 41: / Line 42: @@
 |-
 | valign="top" |
-,000-50,000
+,001-26,000
 | valign="top" |
-**
+to 8
 | valign="top" |
 Gb
@@ Line 50: / Line 51: @@
 | valign="top" |
 X 10 Gbps
-|-
-| valign="top" |
-Above 50,000
-| valign="top" |
-**
-| valign="top" |
-+ Gb
-| valign="top" |
-Gb
-| valign="top" |
-Multiple 10 Gbps
 |}
 <nowiki>**</nowiki> The CPU number is based on Intel R630 with Xeon E5-2643. Double the CPUs number if yours are from a earlier generations.
-More details on HW/CPU/NIC requirements can be found here: [[FreeSBC:RequirementsMatrix|RequirementsMatrix]]
+More details on HW/CPU/NIC requirements can be found here: [[FreeSBC:RequirementsMatrix|Requirements Matrix]]
-For better performance (see [[TSBC-SW:Cloud:VmWare_Optimizations|optimization]] section)
+For better performance use these settings:
 * CPU resource: allocation shares set to 'high'
 * CPU resource: reservation set to maximum and no limit (i.e. 'unlimited')
@@ Line 75: / Line 65: @@
 == Getting the Image ==
-Please contact our sales team at sales@telcobridges.com to get a copy of the latest TBSC Image.
+Please go to our [http://www2.telcobridges.com/ProSBCDownload ProSBC Download site]  to get a copy of the latest SBC Image.
 == Installation on VmWare cloud ==
-=== TBSC VmWare Image ===
+=== ProBSC VmWare Image ===
 A virtual machine image is a single file that contains a virtual disk that has a bootable operating system installed on it. Images are used to create virtual machine instances within the cloud.
-You will need to upload the latest TSBC image into your VmWare before you can launch a virtual machine instance running the TSBC software.
+You will need to upload the latest SBC image into your VmWare before you can launch a virtual machine instance running the SBC software.
 ==== Launching an instance ====
@@ Line 90: / Line 80: @@
 [[TSBC-SW:Cloud:VmWare_Launching_Instance_vSphere_A|Using the vSphere client application]]
-=== Accessing the TSBC-SW ===
+If you are installing a standalone SBC, the ProSBC or FreeSBC will need access to LAN/WAN and MGMT networks. For transcoding on TSBC-HW-TRANS, or HA pair installation, the ProSBC will also need access to CTRL0/CTRL1, and TRANS0/TRANS1 networks. In both instance launching methods above, when editing network adaptor, please take reference to [[TSBC-SW:Networking|ProSBC Networking]] for details on network requirements. <br>
+For ProSBC Transcoding and associated network setup please also see [[FreeSBC:Transcoding and Network Setup]].
-==== Accessing the TSBC-SW web portal ====
+=== Accessing the SBC ===
-* Open a web browser to the management IP of the TSBC, on port 12358.  Example if your server address is 192.168.178.30, the URL would be: <br/> http://192.168.178.30:12358
+==== Assigning IP address ====
+By default, all detect network interfaces will have DHCP enabled.  Thus, the server might already have an IP address assigned if the network has a DHCP server running.  In such case, you can display and use it to access the web portal configuration panel.
+# Retrieve an IP address assigned by DHCP
+  # ifconfig
+If you want to assigned a static IP address or there are no DHCP on your network, you will need to configure it manually.
+# Use '''tbchangeip''' shell command and answered questions to changed your Ethernet interface address:
+  # tbchangeip
+==== Accessing the SBC web portal ====
+* Open a web browser to the management IP of the SBC, on port 12358.  Example if your server address is 192.168.178.30, the URL would be: <br/> http://192.168.178.30:12358
 <br/>
-:You should get to the TSBC Configuration Wizard <br/>
+:You should get to the SBC Configuration Wizard <br/>
 :[[File:TSBC_WebPortal_Configuration_wizard.jpg|700px]]
 <br/>
@@ Line 105: / Line 108: @@
 == Web Portal Initial Configuration ==
 Click on the following link to pursue installation from the web portal:
-[[TSBC-SW:WebPortal:Initial Configuration]]
+[[TSBC-SW:WebPortal:Initial Configuration|SBC Initial Configuration]]
-== Optimizations ==
-Click on the following link for VmWare optimizations:
-[[TSBC-SW:Cloud:VmWare_Optimizations]]

FreeSBC:Cloud:VmWare Installation A

Latest revision as of 11:19, 26 January 2021

Contents

Requirements

Getting the Image

Installation on VmWare cloud

ProBSC VmWare Image

Launching an instance

Accessing the SBC

Assigning IP address

Accessing the SBC web portal

Web Portal Initial Configuration

Views

Personal tools

Navigation

Search

Toolbox