Configuring Toolpack:SIP to ISDN Gateway
From TBwiki
(Difference between revisions)
(improve introduction and before starting section) |
(update before start section) |
||
| (One intermediate revision by one user not shown) | |||
| Line 1: | Line 1: | ||
== Introduction == | == Introduction == | ||
| − | This guide is intended to help Toolpack user to configure a [[SIP|SIP]] to [[ISDN|ISDN]] Gateway.<br> | + | This guide is intended to help Toolpack user to configure a [[SIP|SIP]] to [[ISDN|ISDN]] Gateway.<br> |
| − | <br> | + | <br> |
| − | This guide assumes the following:<br> | + | This guide assumes the following:<br> |
| − | *Toolpack version is v2.4.<br> | + | *Toolpack version is v2.4.<br> |
| − | *Toolpack is already installed and running on the host.<br> | + | *Toolpack is already installed and running on the host.<br> |
| − | *Routing: All incoming [[SIP|SIP]] calls are bridged to [[ISDN|ISDN]] and all incoming [[ISDN|ISDN]] calls are bridged to [[SIP|SIP]]. | + | *The system contain 1 [[SIP|SIP]] provider and 1 [[ISDN|ISDN]] provider.<br> |
| + | *Routing: All incoming [[SIP|SIP]] calls are bridged to [[ISDN|ISDN]] and all incoming [[ISDN|ISDN]] calls are bridged to [[SIP|SIP]].<br> | ||
| + | *[[Text Call Detail Records (CDR)|CDR]] will be saved using [[Text cdr|Toolpack text CDR]]<br> | ||
| − | <br> | + | <br> |
== Before starting == | == Before starting == | ||
| − | Here is a list of ''mandatory'' information that the user must know ''before'' configuring Toolpack:<br> | + | Here is a list of ''mandatory'' information that the user must know ''before'' configuring Toolpack:<br> |
| + | |||
| + | === [[ISDN|ISDN]] === | ||
| + | |||
| + | *[[Line Interface|Line Interface(s)]] type and parameters (T1, E1, DS3, STM-1).<br> | ||
| + | *[[Line Service|Line Service(s)]] type and parameters.<br> | ||
| + | *ISDN stack(s) variant(s).<br> | ||
| + | *Network side: User or network. | ||
| + | |||
| + | <br> | ||
| + | |||
| + | === [[SIP|SIP]]<br> === | ||
| + | |||
| + | *SIP IP address(es) (IP address of your system where the SIP signaling will be incoming).<br> | ||
| + | *SIP provider(s)/consumers IP address(es) (remote IP address).<br> | ||
| + | *SIP port (default:5060).<br> | ||
| + | *SIP port type: UDP or TCP (default: UDP). | ||
| + | |||
| + | <br> | ||
| + | |||
| + | == Configuration == | ||
| + | |||
| + | <br> | ||
| + | |||
| + | === ISDN Configuration<br> === | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
<br> | <br> | ||
Latest revision as of 11:26, 22 January 2010
Contents |
Introduction
This guide is intended to help Toolpack user to configure a SIP to ISDN Gateway.
This guide assumes the following:
- Toolpack version is v2.4.
- Toolpack is already installed and running on the host.
- The system contain 1 SIP provider and 1 ISDN provider.
- Routing: All incoming SIP calls are bridged to ISDN and all incoming ISDN calls are bridged to SIP.
- CDR will be saved using Toolpack text CDR
Before starting
Here is a list of mandatory information that the user must know before configuring Toolpack:
ISDN
- Line Interface(s) type and parameters (T1, E1, DS3, STM-1).
- Line Service(s) type and parameters.
- ISDN stack(s) variant(s).
- Network side: User or network.
SIP
- SIP IP address(es) (IP address of your system where the SIP signaling will be incoming).
- SIP provider(s)/consumers IP address(es) (remote IP address).
- SIP port (default:5060).
- SIP port type: UDP or TCP (default: UDP).
Configuration
ISDN Configuration
