Toolpack:Creating an MTP3 Linkset A
From TBwiki
(Difference between revisions)
(Created page with 'Now that you have created an MTP3 network, you are ready to create an MTP3 linkset. This can be done through the MTP3 network configuration window To create an MTP3 linkset: 1-…') |
|||
| (7 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | Now that you have created an MTP3 network, you are ready to create an MTP3 linkset. This can be done through the MTP3 network configuration window | + | === '''''Applies to version(s): v2.5, v2.6., v2.7''''' === |
| + | {{DISPLAYTITLE:Creating an MTP3 Linkset}} | ||
| + | Now that you have created an MTP3 network, you are ready to create an MTP3 linkset. This can be done through the MTP3 network configuration window. A linkset is used to logically combine multiple MTP3 links going to the same DPC into a single entity. One linkset could be the links between a point code identifying the Tmedia/Tdev SS7 node and a point code identifying the adjacent SS7 equipment. | ||
To create an MTP3 linkset: | To create an MTP3 linkset: | ||
| + | |||
1- Click '''Create New Mtp3 Linkset''' in the MTP3 Network configuration panel | 1- Click '''Create New Mtp3 Linkset''' in the MTP3 Network configuration panel | ||
| Line 10: | Line 13: | ||
* Enter a '''name''' for the linkset | * Enter a '''name''' for the linkset | ||
| − | * Select an ''' | + | * Select an '''origin point code''' (OPC) |
| − | * Select | + | * Select an '''adjacent point code''' |
| + | * Make sure the '''desired state''' is set to '''Active''' | ||
* Click '''Create''' | * Click '''Create''' | ||
[[Image:Toolpack_v2.5_Creating_MTP3_Linkset.png]] | [[Image:Toolpack_v2.5_Creating_MTP3_Linkset.png]] | ||
| − | 3- Verify that the '''Mtp3Linkset was successfully created''' message appears | + | 3- Verify that the '''"Mtp3Linkset was successfully created"''' message appears |
[[Image:Toolpack_v2.5_MTP3_Linkset_Created.png]] | [[Image:Toolpack_v2.5_MTP3_Linkset_Created.png]] | ||
| + | |||
| + | |||
| + | ==List of Parameters== | ||
| + | |||
| + | * [[Parameter: Name|Name]] | ||
| + | * [[Parameter: Origin Point Code|Origin Point Code]] | ||
| + | * [[Parameter: Adjacent Point Code|Adjacent Point Code]] | ||
| + | * [[Parameter: Desired State|Desired State]] | ||
Latest revision as of 10:21, 15 July 2013
Applies to version(s): v2.5, v2.6., v2.7
Now that you have created an MTP3 network, you are ready to create an MTP3 linkset. This can be done through the MTP3 network configuration window. A linkset is used to logically combine multiple MTP3 links going to the same DPC into a single entity. One linkset could be the links between a point code identifying the Tmedia/Tdev SS7 node and a point code identifying the adjacent SS7 equipment.
To create an MTP3 linkset:
1- Click Create New Mtp3 Linkset in the MTP3 Network configuration panel
2- Configure the new linkset:
- Enter a name for the linkset
- Select an origin point code (OPC)
- Select an adjacent point code
- Make sure the desired state is set to Active
- Click Create
3- Verify that the "Mtp3Linkset was successfully created" message appears
