Toolpack:Adding an Adapter D
From TBwiki
(Difference between revisions)
(→Applies to version v2.8: revsised the note in step 3) |
(→Applies to version v2.8: typo fix and some minor rephrasing) |
||
| Line 6: | Line 6: | ||
[[Image:Schematic-pair-of-tmp6400s.jpg|thumb|250px|Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser]] | [[Image:Schematic-pair-of-tmp6400s.jpg|thumb|250px|Schematic showing 2 TMP6400 devices with an external server and a second machine with a web browser]] | ||
| − | In order | + | In order to add one or more additional hardware devices to the Toolpack system configuration, their serial numbers must be registered with the Toolpack application server. |
| Line 28: | Line 28: | ||
* Select the appropriate '''hardware device''' from the Type field. (In this case select TMP) | * Select the appropriate '''hardware device''' from the Type field. (In this case select TMP) | ||
* Select the type of TDM lines that the hardware device will support. | * Select the type of TDM lines that the hardware device will support. | ||
| − | * Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field | + | * Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field empty. |
| − | * Provide the amount of time | + | * Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade. |
* Enter the location in which the hardware device is installed. | * Enter the location in which the hardware device is installed. | ||
| − | * Enter a meaningful description | + | * Enter a meaningful description about the use or purpose of the hardware device. |
* Select '''Enabled''' from the Target State field. | * Select '''Enabled''' from the Target State field. | ||
* Click '''Create''' | * Click '''Create''' | ||
| Line 43: | Line 43: | ||
[[Image:Hardware_3_A.png]] | [[Image:Hardware_3_A.png]] | ||
| − | 4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below | + | 4- Verify that the '''"Adapter was successfully created"''' message appears, and that the newly added hardware device appears in the '''Hardware List''' below. |
Revision as of 09:49, 27 May 2015
Applies to version v2.8
When you receive a new system, at least one hardware configuration is available (by default) in the Toolpack application server. To add other hardware devices, use the Tmedia Web Portal.
In order to add one or more additional hardware devices to the Toolpack system configuration, their serial numbers must be registered with the Toolpack application server.
To add a hardware device:
1- Click Hardware Units in the navigation panel
2- Click Create New Units, to add a new hardware device
3- Enter a name for the hardware device
- Enter the serial number of the new hardware device (filling in the Serial Number field will cause auto-completion of the field to occur).
- Select the appropriate hardware device from the Type field. (In this case select TMP)
- Select the type of TDM lines that the hardware device will support.
- Indicate if the device will operate as a backup in an N+1 configuration. If this is the first device being added, leave this field empty.
- Provide the amount of time in seconds, that the system will wait for calls to complete before shutting down for an upgrade.
- Enter the location in which the hardware device is installed.
- Enter a meaningful description about the use or purpose of the hardware device.
- Select Enabled from the Target State field.
- Click Create
NOTE The following image shows the N+1 Backup field set. This is done for the addition of a secondary device that will operate as the designated 1+1 backup in a 1+1 or N+1 group.
4- Verify that the "Adapter was successfully created" message appears, and that the newly added hardware device appears in the Hardware List below.
