Toolpack:Creating a 1+1 Group C
From TBwiki
(Difference between revisions)
(→Applies to version v2.9) |
(removed patch panel ports mapping from NI section) |
||
| Line 48: | Line 48: | ||
primary_unit = "@[hardware_name]" | primary_unit = "@[hardware_name]" | ||
secondary_np1_patch_panel = "NONE" | secondary_np1_patch_panel = "NONE" | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</pre> | </pre> | ||
| Line 75: | Line 57: | ||
"backup_unit" : "@[hardware_name]", | "backup_unit" : "@[hardware_name]", | ||
"name" : "@[np1Group_name]", | "name" : "@[np1Group_name]", | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
"primary_np1_patch_panel" : "NONE", | "primary_np1_patch_panel" : "NONE", | ||
"primary_unit" : "@[hardware_name]", | "primary_unit" : "@[hardware_name]", | ||
| Line 98: | Line 63: | ||
</pre> | </pre> | ||
</div> | </div> | ||
| + | |||
==List of Parameters== | ==List of Parameters== | ||
Revision as of 10:45, 16 December 2015
Applies to version v2.9
A 1+1 group indentifies the two Tmedia hardware devices that operate together to provide 1+1 backup protection. One device is identified as the primary hardware device, while the other device is identified as the backup hardware device. To create a 1+1 group, you must use the Tmedia Web Portal.
To create a 1+1 group:
1- Click 1+1 in the navigation panel
2- Click Create New 1+1 Group
3- Enter the serial numbers of the primary and 1+1 backup hardware devices.
- Provide a name for the 1+1 group.
- Select the serial number of the primary hardware device. (This field may already be filled.)
- Select the serial number of the 1+1 backup hardware device.
- Set Auto switch-back to cause an automatic switch back to the original primary hardware device when it becomes available. If the field is clear (not checked), then a switch back to the original device will occur only after a manual reboot of the system.
- Click Create
4- Verify that the newly added 1+1 group appears in the 1+1 Groups list.
Path
/configurations/@[configuration_name]/np1_groups/@[np1Group_name]
Parameters (text)
/configurations/Sylvain/np1_groups/One_PLUS_ONE_GROUP auto_switch_back = false backup_unit = "@[hardware_name]" name = "@[np1Group_name]" primary_np1_patch_panel = "NONE" primary_unit = "@[hardware_name]" secondary_np1_patch_panel = "NONE"
Parameters (json)
{
"auto_switch_back" : false,
"backup_unit" : "@[hardware_name]",
"name" : "@[np1Group_name]",
"primary_np1_patch_panel" : "NONE",
"primary_unit" : "@[hardware_name]",
"secondary_np1_patch_panel" : "NONE"
}
