Toolpack:Creating a SIP Domain SBC A
From TBwiki
(Difference between revisions)
| Line 25: | Line 25: | ||
** '''Register source''': Sends SIP Invite to the registering source IP address. | ** '''Register source''': Sends SIP Invite to the registering source IP address. | ||
** '''Contact''': Sends SIP Invite to the 'contact' from the Register message. | ** '''Contact''': Sends SIP Invite to the 'contact' from the Register message. | ||
| − | * Set the 'Default Contact Expiration' value when | + | * Set the 'Default Contact Expiration', this value will be used when no ''Expires'' value is supplied by the user agent. |
| − | * Set the 'Minimum Contact Expiration' ''Expires'' value | + | * Set the 'Minimum Contact Expiration', this is the minimum ''Expires'' value that can be supplied by a user agent. Lower values will be rejected with a 423 'Interval too brief' response. |
| − | * Set the 'Maximum Contact Expiration' ''Expires'' value | + | * Set the 'Maximum Contact Expiration', this is the maximum ''Expires'' value that can be supplied by a user agent. Higher value are replaced by this parameter. |
* Forwarding Parameters: | * Forwarding Parameters: | ||
** Select the Registration '''Forwarding Mode''' to the registrar: | ** Select the Registration '''Forwarding Mode''' to the registrar: | ||
*** '''Contact Remapping''': Changes the user and the IP address. | *** '''Contact Remapping''': Changes the user and the IP address. | ||
*** '''Contact Passthrough''': Doesn't change anything. Enables devices to be contacted directly without going through the SBC. | *** '''Contact Passthrough''': Doesn't change anything. Enables devices to be contacted directly without going through the SBC. | ||
| − | ** Set 'Minimum Registrar Expiration' ''Expires'' value sent to the registrar. | + | ** Set 'Minimum Registrar Expiration' ''Expires'' value sent to the registrar. If a user agent 'Expires' value is greater than this parameter value, rate adaptation will take place. |
| − | ** Set 'Maximum Pending Register Forward', the maximum number of simultaneous pending register requests allowed for this domain. | + | ** Set 'Maximum Pending Register Forward', the maximum number of simultaneous pending register requests allowed for this domain. New REGISTER request are being refused passed this threshold. |
| − | ** Set 'Maximum Simultaneous Register Forward', the maximum number of simultaneous active register requests allowed for this domain. | + | ** Set 'Maximum Simultaneous Register Forward', the maximum number of simultaneous active register requests allowed for this domain. New REGISTER request are being refused passed this threshold. |
* Click '''Create''' | * Click '''Create''' | ||
Revision as of 15:35, 26 July 2017
Applies to version(s): v3.0
A SIP domain represents a grouping of devices (or users) that can communicate with one another. You must configure SIP Registration Domain for your system. The first step in doing so is to create a SIP Domain:
1- Click SIP Domain in the navigation panel
2- Click Create New Domain
3- Create the new Domain:
- Enter a configuration Name for this domain.
- Enter a Domain Name for the SIP Registration Domain (domain can be a FQDN or an IP address)
- Set the number 'Maximum Registered Users' for this domain
- Set the Expires value used by SBC when the remote device doesn't supply one (Default Contact Expire)
- Select Routing Method the system will use to route calls to registered users (if enabled in routing scripts).
- Register source: Sends SIP Invite to the registering source IP address.
- Contact: Sends SIP Invite to the 'contact' from the Register message.
- Set the 'Default Contact Expiration', this value will be used when no Expires value is supplied by the user agent.
- Set the 'Minimum Contact Expiration', this is the minimum Expires value that can be supplied by a user agent. Lower values will be rejected with a 423 'Interval too brief' response.
- Set the 'Maximum Contact Expiration', this is the maximum Expires value that can be supplied by a user agent. Higher value are replaced by this parameter.
- Forwarding Parameters:
- Select the Registration Forwarding Mode to the registrar:
- Contact Remapping: Changes the user and the IP address.
- Contact Passthrough: Doesn't change anything. Enables devices to be contacted directly without going through the SBC.
- Set 'Minimum Registrar Expiration' Expires value sent to the registrar. If a user agent 'Expires' value is greater than this parameter value, rate adaptation will take place.
- Set 'Maximum Pending Register Forward', the maximum number of simultaneous pending register requests allowed for this domain. New REGISTER request are being refused passed this threshold.
- Set 'Maximum Simultaneous Register Forward', the maximum number of simultaneous active register requests allowed for this domain. New REGISTER request are being refused passed this threshold.
- Select the Registration Forwarding Mode to the registrar:
- Click Create
4- Verify that the Sip registration domain was successfully created message appears
