Toolpack v2.4:Create Line Interfaces
From TBwiki
(Difference between revisions)
(Created page with 'Note: To add a line interface, the Tmedia unit must have a TDM module installed. == To add a line interface == '''1. Select Line Interfaces from the navigation panel.''' [[Im…') |
(→To add a line interface) |
||
| Line 3: | Line 3: | ||
== To add a line interface == | == To add a line interface == | ||
| − | '''1. Select Line Interfaces from the navigation panel.''' | + | '''1. Select "Line Interfaces" from the navigation panel.''' |
| − | [[Image: | + | [[Image:Web_Portal_v2.4_Navigation_Panel_Line_Interfaces.png]] |
| − | '''2. Click Create New Line Interface from the Information panel.''' | + | '''2. Click "Create New Line Interface" from the Information panel.''' |
| − | [[Image:Web_Portal_v2. | + | [[Image:Web_Portal_v2.4_Create_Line_Interface.png|700px]] |
| − | '''3. To create a | + | '''3. To create a new line interface''': |
| − | *Enter a name for the line interface, and set the Line Type | + | *Enter a name for the line interface, and set the Line Type (this setting will depend on the hardware adapter selected) |
| − | *The local indexes for trunks are zero-based values. This means that local index 0 is trunk 1 and local index 1 is trunk 2. Enter a local index number, assigning a different value to each | + | *Select a local index number for each line. The local indexes for trunks are zero-based values. This means that local index 0 is trunk 1 and local index 1 is trunk 2. Enter a local index number, assigning a different value to each line interface. |
| − | * | + | *Set all necessary parameters for the line type chosen (Line Length, Encoding, Signal Level, etc...) |
| − | * | + | *Click "Create" |
| − | |||
| − | + | [[Image:Web_Portal_v2.4_Creating_Line_Interface.png|700px]] | |
| − | [[Image:Web_Portal_v2. | + | |
| Line 34: | Line 32: | ||
| − | [[Image:Web_Portal_v2. | + | [[Image:Web_Portal_v2.4_Line_Interface_Created.png|700px]] |
| − | '''4. To view a listing of the line interfaces click List.''' | + | '''4. To view a listing of the line interfaces click "List".''' |
| Line 45: | Line 43: | ||
The Line Interface List is displayed. | The Line Interface List is displayed. | ||
| − | [[Image:Web_Portal_v2. | + | [[Image:Web_Portal_v2.4_Line_Interface_List.png|700px]] |
== Verifying Status == | == Verifying Status == | ||
Revision as of 11:31, 6 December 2009
Note: To add a line interface, the Tmedia unit must have a TDM module installed.
To add a line interface
1. Select "Line Interfaces" from the navigation panel.
2. Click "Create New Line Interface" from the Information panel.
3. To create a new line interface:
- Enter a name for the line interface, and set the Line Type (this setting will depend on the hardware adapter selected)
- Select a local index number for each line. The local indexes for trunks are zero-based values. This means that local index 0 is trunk 1 and local index 1 is trunk 2. Enter a local index number, assigning a different value to each line interface.
- Set all necessary parameters for the line type chosen (Line Length, Encoding, Signal Level, etc...)
- Click "Create"
The 'Line Interface was successfully created' message is displayed.
4. To view a listing of the line interfaces click "List".
The Line Interface List is displayed.
Verifying Status
To verify the status of the line interface, either select Status from the Navigation panel or select the Status tab in the Information panel.
