Redundancy & High Availability:Network
m (add more details) |
(add TMS network information) |
||
| Line 5: | Line 5: | ||
TelcoBriges recommends the use of 2 Gigabytes Ethernet Switches for a [[Tmedia]] system. | TelcoBriges recommends the use of 2 Gigabytes Ethernet Switches for a [[Tmedia]] system. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| Line 45: | Line 37: | ||
== TMS Network == | == TMS Network == | ||
| − | The TMS network is only available for the [[TMG7800]] model. | + | The TMS network is only available for the [[TMG7800]] model. It allows a TMG7800 system to bridge call legs between TMG7800 Telecom Units. It is possible to connect 2 TMG7800 Telecom Units together using RJ45 shielded CAT7 Ethernet cross-over cables. For more than 2 TMG7800 Telecom Units, the TMG7800 system requires a TMG7800-TMS. Each TMG7800 Telecom Units are supplied with 2 TMS interfaces. TelcoBridges recommends to connect both cables to protect against failure. |
| + | |||
| + | [[Image:Ha_TMS_Network_Back_2_Back.png|TMG7800 TMS Network Back to Back]] | ||
| + | |||
| + | [[Image:Ha_TMS_Network_With_TMG7800-TMS.png|TMG7800 TMS Network With TMG7800-TMS]] | ||
| + | |||
| + | [[Image:Ha_TMS_Network_With_TMG7800-TMS_Failure.png|TMG7800 TMS Network With TMG7800-TMS With Failure]] | ||
Revision as of 09:04, 9 February 2011
Networking is a critical section of the system that is sometimes overlooked. An adequate network will avoid problems like congestion or disconnection.
Contents |
Network Redundancy
TelcoBriges recommends the use of 2 Gigabytes Ethernet Switches for a Tmedia system.
VoIP Network
The VoIP network are secured interfaces that are use to send signaling and data packets over Ip networks (i.e. Sip, Sigtran, RTP). They are considered secured because it is not possible to control the Tmedia through those interfaces. TelcoBridges provides 2 VoIP ports on all its VoIP Gateway models.
A different subnet is required for each VoIP interface. The obvious use of the 2 VoIP ports is to connect one port with a private network and the other to the public network. A second application of the 2 VoIP ports are to connect to your providers using 2 different networks.
Here is an example of VoIP network redundancy with a TMG3200
If one of the network is down (because of a switch or cable malfunction), the other network can still reach the providers as seen in the next example
Control Network
The Control network is only available for the TMG7800 model. The control network allows the TMG-CONTROL to manage the TMG7800 Telecom units. Each TMG7800 units contains 2 control network interfaces labeled ETH0 and ETH1 respectively. The control network should be on private subnets to avoid lost of packets between the TMG7800 units. Which is why TelcoBridges recommends the use of 2 Ethernet switches one for interfaces.
Here is an example of the TMG7800 control network.
As shown in the next example, the system remains operational even if there is a network failure
TMS Network
The TMS network is only available for the TMG7800 model. It allows a TMG7800 system to bridge call legs between TMG7800 Telecom Units. It is possible to connect 2 TMG7800 Telecom Units together using RJ45 shielded CAT7 Ethernet cross-over cables. For more than 2 TMG7800 Telecom Units, the TMG7800 system requires a TMG7800-TMS. Each TMG7800 Telecom Units are supplied with 2 TMS interfaces. TelcoBridges recommends to connect both cables to protect against failure.
TMG7800 TMS Network Back to Back
