Configure NFAS A
(Created page with 'Now you must configure ISDN-PRI signaling for your system. To do so, you must create a new ISDN stack. Integrated Systems Digital Network (ISDN) is a circuit-switched telephone …') |
|||
| Line 22: | Line 22: | ||
* Verify that the box labeled '''Enabled''' is checked | * Verify that the box labeled '''Enabled''' is checked | ||
* Enter a '''name''' for the new ISDN stack | * Enter a '''name''' for the new ISDN stack | ||
| − | * Select a ''' | + | * Select a '''variant''' to associate with the stack |
| − | + | ||
* Determine whether the stack will operate on the '''user side''', or the '''network side''' | * Determine whether the stack will operate on the '''user side''', or the '''network side''' | ||
| + | * Select a '''primary D-channel line service''' | ||
* Click '''Create''' | * Click '''Create''' | ||
| − | [[Image: | + | [[Image:Creating_new_stack.jpg]] |
4- Verify that the '''"ISDN stack was successfully created"''' message appears, and that the new stack is listed in the '''ISDN Stack List''' | 4- Verify that the '''"ISDN stack was successfully created"''' message appears, and that the new stack is listed in the '''ISDN Stack List''' | ||
| − | [[Image: | + | [[Image:ISDN_stack_success.jpg]] |
| + | |||
| + | |||
| + | 5- Create a backup line: | ||
| + | |||
| + | * Click on the '''Available''' line on the righthand side of the screen, and select the arrow to add it to the '''Current-Line Services''' | ||
| + | * Select the line service that will be used as a D-channel backup by this ISDN stack instance. | ||
| + | * Click '''Save''' | ||
| + | |||
| + | [[Image:Verify_ISDN_stack.jpg]] | ||
| + | |||
| + | |||
| + | 6- Verify that the '''"ISDN stack was successfully updated"''' message appears, and that the new '''trunk''' line is listed in the '''ISDN Stack List''' | ||
| + | |||
| + | [[Image:Isdn_stack_success_updated.jpg]] | ||
| Line 42: | Line 56: | ||
* [[Parameter: Variant|Variant]] | * [[Parameter: Variant|Variant]] | ||
* [[Parameter: Side|Side]] | * [[Parameter: Side|Side]] | ||
| + | * [[Parameter: Trunk|Trunk]] | ||
Revision as of 19:56, 18 July 2011
Now you must configure ISDN-PRI signaling for your system. To do so, you must create a new ISDN stack.
Integrated Systems Digital Network (ISDN) is a circuit-switched telephone system that integrated voice and data on the same lines.Tmedia and Tdev systems can be configured to provide an ISDN signaling stack on the trunks of one or more units to meet system configuration requirements.
To create a new ISDN stack:
1- Click ISDN in the navigation menu, under the Signaling header
2- Click Create New ISDN Stack
3- Create the new stack:
Note: TelcoBridges offers several ISDN variants, four of which support NFAS. By clicking on 'Create' you confirm the line service and in the case of ISDN variants which support NFAS you are permitted to add additional line services.
- Verify that the box labeled Enabled is checked
- Enter a name for the new ISDN stack
- Select a variant to associate with the stack
- Determine whether the stack will operate on the user side, or the network side
- Select a primary D-channel line service
- Click Create
4- Verify that the "ISDN stack was successfully created" message appears, and that the new stack is listed in the ISDN Stack List
5- Create a backup line:
- Click on the Available line on the righthand side of the screen, and select the arrow to add it to the Current-Line Services
- Select the line service that will be used as a D-channel backup by this ISDN stack instance.
- Click Save
6- Verify that the "ISDN stack was successfully updated" message appears, and that the new trunk line is listed in the ISDN Stack List
