FreeSBC:Cloud:VmWare Installation
Contents |
Requirements
Minimal Cloud requirements:
- Vmware ESX 5 or 6
- 64-bit infrastructure only
- E1000 NIC emulation or VMXNET3 interfaces
- One Ethernet adapter for management (mgmt0)
- One or more Ethernet adapter(s) for SIP and RTP traffic according to the table below (LAN/WAN)
- If you are deploying FreeSBC with transcoding devices or in a 1+1 configuration, you will two additional Ethernet adapters to be used as control ports (ctrl0/ctrl1).
| Sessions | CPU | RAM | Disk Space | Data Ethernet ports |
|---|---|---|---|---|
|
Up to 5,000 |
2 |
4 Gb |
40 Gb |
1 Gbps |
|
5,001-20,000 |
4 |
8 Gb |
60 Gb |
4 X 1 Gbps or 1 X 10 Gbps |
|
20,001-50,000 |
4** |
16 Gb |
80 Gb |
1 X 10 Gbps |
|
Above 50,000 |
6** |
24+ Gb |
100 Gb |
Multiple 10 Gbps |
** The CPU number is based on Intel R630 with Xeon E5-2643. Double the CPUs number if yours are from a earlier generations.
More details on HW/CPU/NIC requirements can be found here: Requirements Matrix
For better performance (see optimization section)
- CPU resource: allocation shares set to 'high'
- CPU resource: reservation set to maximum and no limit (i.e. 'unlimited')
- Memory resource: reserve all guest memory (all locked)
- Disk: shares 'high'
- Advanced CPU: Hyperthread core sharing to 'None'
- Latency Sensitivity: 'High'
Getting the Image
Please go to our FreeSBC Download site to get a copy of the latest TBSC Image.
Installation on VmWare cloud
TBSC VmWare Image
A virtual machine image is a single file that contains a virtual disk that has a bootable operating system installed on it. Images are used to create virtual machine instances within the cloud.
You will need to upload the latest TSBC image into your VmWare before you can launch a virtual machine instance running the TSBC software.
Launching an instance
Using the vSphere client application
If you are installing a standalone SBC, the FreeSBC will need access to LAN/WAN and MGMT networks. For transcoding on TSBC-TRANS, or HA pair installation, the FreeSBC will also need access to CTRL0, CTRL1, /and TRANS0 networks. In both instance launching methods above, when editing network adaptor, please take reference to TSBC-SW:Networking for details on network requirements. For FreeSBC Transcoding and associated network setup please also see FreeSBC:Transcoding and Network Setup.
Accessing the TSBC-SW
Assigning IP address
By default, all detect network interfaces will have DHCP enabled. Thus, the server might already have an IP address assigned if the network has a DHCP server running. In such case, you can display and use it to access the web portal configuration panel.
- Retrieve an IP address assigned by DHCP
# ifconfig
If you want to assigned a static IP address or there are no DHCP on your network, you will need to configure it manually.
- Use tbchangeip shell command and answered questions to changed your Ethernet interface address:
# tbchangeip
Accessing the TSBC-SW web portal
- Open a web browser to the management IP of the TSBC, on port 12358. Example if your server address is 192.168.178.30, the URL would be:
http://192.168.178.30:12358
- You should get to the TSBC Configuration Wizard
- If you do not know the IP address, you can find it from the VMware interface:
- From here, you can go to Web Portal Initial Configuration Guide to continue the installation, and/or optimize your server to get the maximum out of your server.
Web Portal Initial Configuration
Click on the following link to pursue installation from the web portal: TSBC-SW:WebPortal:Initial Configuration
Optimizations
Click on the following link for VmWare optimizations: TSBC-SW:Cloud:VmWare_Optimizations
