IP Transcoding Unit Configuration Use Case:Two subnet, Two IP Addresses, tagged

From TBwiki
Revision as of 09:38, 15 December 2020 by Allyntree (Talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search


This article applies to: Product Version
SBC 3.0, 3.1


Contents

Perequisites

Perequisites
  • ProSBC (or Tsbc) Host
Network device name    Network device role    Network Config
-------------------    -------------------    -------------------
mgmt0                  mgmt                   Untagged
wan0                   LAN/WAN                Tagged 1650
lan0                   LAN/WAN                Tagged 1651
trans0                 LAN/WAN                Tagged 752     
trans1                 LAN/WAN                Tagged 753     
ctrl0                  ctrl0                  Tagged 750
ctrl1                  ctrl1                  Tagged 751             

NOTE: The 'Network device names' for transcoding must be trans0 and trans1

  • Hardware Unit - TB002177 is the TSBC-HW-TRANS unit in the below setup
 Network device name    Network device role    Network Config
-------------------    -------------------    -------------------
voip0                   LAN/WAN                Tagged 752
voip1                   LAN/WAN                Tagged 753
eth0                    ctrl0                  Untagged PVID 750  **
eth1                    ctrl1                  Untagged PVID 751  **

NOTE: On the network switch, the control ports on the Hardware unit need to be configure with Link Type: Access

Two subnet, Two IP Addresses, tagged

UseCase TsbcHwTranscoding.png


Network configuration

Configure IP Network for wan0 Configure IP Network for lan0 Configure IP Network for trans0 Configure IP Network for trans1
  • Create wan0 IP Address:
    • Name: wan0
    • Service to use: RTP, SIP
    • Host VLAN: vp_wan0:vlan_1650
    • IP address: 192.168.150.1
    • Netmask: 255.255.255.0


  • Create lan0 IP Address:
    • Name: lan0
    • Service to use: RTP, SIP
    • Host VLAN: vp_lan0:vlan_1651
    • IP address: 192.168.151.1
    • Netmask: 255.255.255.0


  • Create trans0 IP Address:
    • Name: trans0
    • Service to use: RTP
    • Host VLAN: vp_trans0:vlan_752
    • IP address: 192.168.152.1
    • Netmask: 255.255.255.0


  • Create trans1 IP Address:
    • Name: trans1
    • Service to use: RTP
    • Host VLAN: vp_trans1:vlan_753
    • IP address: 192.168.153.1
    • Netmask: 255.255.255.0

Transcoding unit configuration

Add transcoding unit


Transcoding unit network configuration

Configure IP Network for voip0 Configure IP Network for voip1
  • Modify voip0 IP Address:
    • Interface Name: voip0
    • Service to use: RTP
    • Virtual port: TB002177:voip0
    • IP address: 192.168.152.10
    • Netmask: 255.255.255.0


  • Modify voip1 IP Address:
    • Interface Name: voip1
    • Service to use: RTP
    • Virtual port: TB002177:voip1
    • IP address: 192.168.153.10
    • Netmask: 255.255.255.0

Sip configuration

Configure SIP
  • Configure SIP
    • For WAN0
      • RTP port ranges parameters:
        • Name: pr_wan0
        • IP Interface: vlan_1650:wan0
        • RTP Port min: 20000
        • RTP Port max: 40000
      • SIP transport server parameters:
        • Name: ts_wan0
        • Port: 5060
        • IP Interface: vlan_1650:wan0
      • SIP NAP parameters:
        • Name: nap_sip_wan0
        • Proxy Address: 192.168.150.10
        • Port Range: vlan_1650:wan0:pr_wan0:20000-40000
        • SIP Transport Servers: ts_wan0
    • For LAN0
      • RTP port ranges parameters:
        • Name: pr_lan0
        • IP Interface: vlan_1651:lan0
        • RTP Port min: 20000
        • RTP Port max: 40000
      • SIP transport server parameters:
        • Name: ts_lan0
        • Port: 5060
        • IP Interface: vlan_1651:lan0
      • SIP NAP parameters:
        • Name: nap_sip_lan0
        • Proxy Address: 192.168.151.10
        • Port Range: vlan_1651:lan0:pr_lan0:20000-40000
        • SIP Transport Servers: ts_lan0
Personal tools