Northbound interface:Enum Values
From TBwiki
Attributes definitions
Enums values
validation_statuses
| Value | Description |
|---|---|
| 'None' | |
| 'Successful' | |
| 'Unknown failure' | |
| 'Timeout occured' |
sig_memory_schemes
| Value | Description |
|---|---|
| 'Base' | 'Base signaling memory scheme: 8 MTP2, 8 M2PA, 4 M2UA, 8 ISUP, 8 SIP, 8 SCTP. These limits are set initially.' |
| 'MTP2 modifier' | 'Overwrite these limits in the base memory scheme: 16 MTP2, 2 M2PA, 2 M2UA. The other limits remain unchanged.' |
| 'SIP modifier' | 'Overwrite these limits in the base memory scheme: 16 SIP, 4 SCTP. The other limits remain unchanged.' |
virtual_adapter_types
| Value | Description |
|---|---|
| 'TDM/IP Gateway' | 'TDM/IP Gateway Units' |
| 'TMS' | 'TMS Units' |
| 'N+1 Patch Panel' | 'N+1 Patch Panel' |
line_interface_physical_types
| Value | Description |
|---|---|
| 'UNKNOWN' | 'Unknown physical Line Interface type' |
| 'OC3_STM1' | 'OC3 or STM1 physical Line Interface (optical connector)' |
| 'DS3' | 'DS3 physical Line Interface' |
| 'E1_T1_J1' | 'E1, T1 or J1 physical Line Interface (either with RJ48 or SCSI connectors)' |
| 'NONE' | 'Unit without any TDM Line Interface' |
vad_noise_floor_levels
| Value | Description |
|---|---|
| 'Auto' | |
| '-96' | |
| '-90' | |
| '-85' | |
| '-80' | |
| '-75' | |
| '-70' | |
| '-65' | |
| '-60' | |
| '-55' | |
| '-50' | |
| '-45' | |
| '-40' | |
| '-35' | |
| '-30' | |
| '-25' | |
| '-20' | |
| '-15' | |
| '-10' | |
| '-5' | |
| '0' |
echo_canceller_gain_power_levels
| Value | Description |
|---|---|
| '-140' | |
| '-130' | |
| '-120' | |
| '-110' | |
| '-100' | |
| '-90' | |
| '-80' | |
| '-70' | |
| '-60' | |
| '-50' | |
| '-40' | |
| '-30' | |
| '-20' | |
| '-10' | |
| '0' | |
| '10' | |
| '20' | |
| '30' | |
| '40' | |
| '50' | |
| '60' |
volume_control_gain_levels
| Value | Description |
|---|---|
| '-18' | |
| '-14' | |
| '-10' | |
| '-6' | |
| '-5' | |
| '-3' | |
| '0' | |
| '3' | |
| '6' | |
| '10' | |
| '14' | |
| '18' |
tone_levels
| Value | Description |
|---|---|
| '-19' | |
| '-15' | |
| '-10' | |
| '-5' | |
| '0' |
t38_max_bitrates
| Value | Description |
|---|---|
| 'NONE' | |
| '2400' | |
| '4800' | |
| '7200' | |
| '9600' | |
| '12000' | |
| '14400' | |
| 'NONE' | |
| '2400' | |
| '4800' | |
| '7200' | |
| '9600' | |
| '12000' | |
| '14400' | |
| '16800' | |
| '19200' | |
| '21600' | |
| '24000' | |
| '26400' | |
| '28800' | |
| '31200' | |
| '33600' |
t38_tcf_transfer_modes
| Value | Description |
|---|---|
| 'Local' | |
| 'Transferred' |
voip_passthrough_detect_types
| Value | Description |
|---|---|
| 'NONE' | 'Fax passthrough will not be detected' |
| 'Silence suppression off' | 'The SDP parameter \'a=silenceSupp:off\' will be used to detect fax passthrough' |
| 'G711 only' | 'The SDP parameter containing only one G711 codec will be used to detect fax passthrough' |
voip_passthrough_codecs
| Value | Description |
|---|---|
| 'PCMU' | |
| 'PCMA' |
fax_relay_detection_modes
| Value | Description |
|---|---|
| 'Standard' | 'Fax tones and T.38 re-invites will trigger fax relay mode. Modem tones and passthrough re-invites will trigger passthrough mode, though fax detection will still continue.' |
| 'Use relay mode on any tone' | 'Both fax and modem tones will immediately cause switch to the chosen relay mode (without going to passthrough first for modem tones).' |
| 'Always relay' | 'Calls are directly invited using the specified relay mode, without waiting for any fax/modem tone. This improves performance when the calls are know to always be fax or modem (e.g. when connecting with a fax server).' |
fax_relay_modes
| Value | Description |
|---|---|
| 'T.38' | 'For FAX: Use T.38 but fallback to passthrough if T.38 is refused. For Modem: Use passthrough.' |
| 'Passthrough' | 'Use passthrough to relay FAX or Modem.' |
adapter_oam_target_states
| Value | Description |
|---|---|
| 'Disabled' | 'Unit is disabled (not used, and backup unit shall not takeover this unit)' |
| 'Maintenance' | 'Unit is in maintenance (not used, but backup unit can takeover this unit)' |
| 'Enabled' | 'Unit is enabled' |
| 'Fault' | 'Fault detected, the unit has been marked as unusable by Toolpack' |
adapter_oam_current_states
| Value | Description |
|---|---|
| 'Unknown' | 'Current state is unknown (not been updated in the database by responsible application yet)' |
| 'Not present' | 'The unit is not present (not connected yet)' |
| 'Configuring' | 'The unit is being configured' |
| 'Ready' | 'The unit is present and ready' |
| 'Ready (backup)' | 'The unit is present and ready as the standby unit of a redundant group' |
| 'Management' | 'The unit is present, but in management state (will not be used for any call)' |
| 'Going management' | 'The unit is present, but going management (waiting until there is no more calls on this unit)' |
| 'Management idle' | 'The unit is present, no more calls on it, and is waiting to be cleared' |
| 'Fault' | 'Failure state, the unit is not working properly after excessive retry' |
adapter_statuses
| Value | Description |
|---|---|
| 'Up' | |
| 'Down' |
tdm_compandings
| Value | Description |
|---|---|
| 'uLaw' | 'uLaw format is used on the TDM bus' |
| 'aLaw' | 'aLaw format is used on the TDM bus' |
voip_codec_assignation_modes
| Value | Description |
|---|---|
| 'Mixed Mode' | 'Mixed mode codec assignation algorithm type' |
| 'Fixed Mode' | 'Fixed mode codec assignation algorithm type (amount of each codec specified)' |
np1_group_functional_states
| Value | Description |
|---|---|
| 'Fault' | 'Group has a \'Fault\' (some Units down and not replaced by the backup Unit)' |
| 'Unprotected' | 'Group is unprotected (backup Unit missing, or patch panel not ready to handle a switch)' |
| 'Unprotected (switched to backup)' | 'Group is unprotected and switched (backup Unit is replacing a primary Unit which is not actually ready to be re-activated)' |
| 'Healthy' | 'Group is healthy, using primary Unit (all primary Units are active, backup Unit is ready to take over)' |
| 'Healthy (backup active)' | 'Group is healthy, using backup Unit (backup Unit is active, replaced primary Unit is ready to take over)' |
ip_interface_presences
| Value | Description |
|---|---|
| 'Unknown' | |
| 'Present' | |
| 'Not present' |
ip_interface_service_types
| Value | Description |
|---|---|
| 'RTP' | 'RTP' |
| 'SIP' | 'SIP' |
| 'SIGTRAN' | 'SIGTRAN' |
| 'MANAGEMENT' | 'MANAGEMENT' |
| 'H248/RADIUS' | 'H248' |
| 'TUNNEL' | 'TUNNEL' |
ip_interface_port_statuses
| Value | Description |
|---|---|
| 'Up' | |
| 'Down' |
ip_interface_port_rates
| Value | Description |
|---|---|
| '1Gbps' | |
| '100Mbps' | |
| '10Mbps' |
ip_interface_port_duplexes
| Value | Description |
|---|---|
| 'Full-duplex' | |
| 'Half-duplex' |
tunnel_types
| Value | Description |
|---|---|
| 'PPPoE' | 'PPPoE' |
sdp_gen_options
| Value | Description |
|---|---|
| 'No session level connection' | 'Session level connection line (\'c=IN IP4 ...\') will be omitted' |
| 'Omit carriage return (OBSOLETE)' | 'Endlines in the generated SDP will not contain the carriage return character' |
| 'Generate all SDP parameters' | 'All parameters in the SDP will be generated, even when default value is used (makes SDP much longer, may cause problem over UDP)' |
| 'Use NSE instead of X-NSE in the NSE MIME' | 'Use NSE instead of X-NSE in the NSE MIME' |
sdp_combine_options
| Value | Description |
|---|---|
| 'Use sender\'s codec order' | 'Sender\'s codec order will be used in the local/remote SDP combine result' |
| 'Ignore incompatible codec parameters' | 'The local/remote SDP combine result will also keep codecs with codec-specific options that don\'t match)' |
| 'Overlook transport directions' | 'The local/remote SDP combine will ignore sendonly or recvonly indications' |
call_supp_info_types
| Value | Description |
|---|---|
| 'Don\'t forward' | 'Don\'t forward to the SS7 network' |
| 'SS7 Suspend/Resume' | 'Suspend/Resume ISUP messages on the SS7 network' |
| 'SS7 Remote Hold/Retrieval' | 'Call progress (CPG) with generic notification indicator indicating remote hold/retrieval (Q.763 section 3.25)' |
hop_counter_handlings
| Value | Description |
|---|---|
| 'Don\'t forward' | 'Don\'t forward the incoming leg\'s hop counter (max fowards) to this outgoing leg' |
| 'Forward' | 'Forward the incoming leg\'s hop counter (max fowards) to the outgoing this (without decrementing)' |
| 'Decrement and forward' | 'Decrement and forward the incoming leg\'s hop counter (max fowards) to this outgoing leg. Drop the call if value reached 1' |
outgoing_early_media_modes
| Value | Description |
|---|---|
| 'Automatic early media detection' | 'Rely on indications in outgoing call\'s signaling to determine if early media is present or not.' |
| 'Always assume early media is present' | 'Consider early media always present on outgoing calls using this profile, no matter what\'s indicated by the signaling.' |
| 'Always ignore early media' | 'Always ignore any early media present on outgoing calls using this profile, no matter what\'s indicated by the signaling.' |
incoming_early_media_modes
| Value | Description |
|---|---|
| 'Forward from outgoing to incoming call' | 'Forward early media indication from outgoing call to corresponding incoming call, if present.' |
| 'Forward if present, otherwise play ring tone' | 'Forward early media indication from outgoing call to corresponding incoming call, if present. Play ring tone to incoming call if corresponding outgoing call does not have early media.' |
| 'Always play ring tone' | 'Always play a ring tone on the incoming call, no matter if there is early media indication on the corresponding outgoing call.' |
| 'Never forward early media' | 'Disable early media on incoming call no matter if there is early media on corresponding outgoing call.' |
ring_tone_start_states
| Value | Description |
|---|---|
| 'Immediately' | 'Ring tone starts (on incoming call) immediately' |
| 'Call Accepted' | 'Ring tone starts (on incoming call) once outgoing call is accepted' |
| 'Call Progress Received' | 'Ring tone starts (on incoming call) once \'Call Progress\' is received on the outgoing call' |
| 'Call Alerted' | 'Ring tone starts (on incoming call) once outgoing call is alerted' |
outgoing_lnp_modes
| Value | Description |
|---|---|
| 'No LNP insertion' | 'No LNP field is inserted in the outgoing leg. (Default)' |
| 'Relay LNP information' | 'LNP fields are inserted in the outgoing leg only if they were received in the incoming leg.' |
| 'Always insert LNP information' | 'LNP fields are inserted in the outgoing leg regardless of their presence in the incoming.' |
incoming_lnp_modes
| Value | Description |
|---|---|
| 'Terminate LNP' | 'Routing is done using the real called party number (not the LRN). LNP fields are ignored for the outgoing leg. (Default)' |
| 'Forward LNP from incoming to outgoing call' | 'Routing is done using the LRN when available otherwise the called party number. LNP fields are kept for possible relay on outgoing leg.' |
| 'Ignore LNP information' | 'Routing is done using the called party number. LNP fields are ignored for the outgoing leg.' |
mlpp_sip_outgoing_modes
| Value | Description |
|---|---|
| 'No MLPP insertion' | 'No MLPP field is inserted in the SIP outgoing leg. (Default)' |
| 'Relay MLPP information' | 'MLPP fields are inserted in the SIP outgoing leg only if they were received in the incoming leg.' |
| 'Always insert MLPP information' | 'MLPP fields are inserted in the SIP outgoing leg regardless of their values in the incoming.' |
mlpp_ss7_outgoing_modes
| Value | Description |
|---|---|
| 'No MLPP insertion' | 'No MLPP field is inserted in the outgoing leg. (Default)' |
| 'Relay MLPP information' | 'MLPP fields are inserted in the outgoing leg only if they were received in the incoming leg. The missing received parameters will be completed by the default values of this profile.' |
| 'Always insert MLPP information' | 'MLPP fields are inserted in the outgoing leg. MLPP fields from the incoming leg will be used if available. The missing received parameters will be completed by the default values of this profile.' |
| 'Forced MLPP information' | 'MLPP profile fields are inserted in the outgoing leg. MLPP fields from the incoming leg will be NOT used.' |
mlpp_sip_resource_priority_namespaces
| Value | Description |
|---|---|
| 'q735' | 'Q.735.3 was created to be a commercial version of the operationally equivalent DSN specification for Multi-Level Precedence and Preemption (MLPP)' |
mlpp_lfb_modes
| Value | Description |
|---|---|
| 'LFB allowed' | 'Indicates that the LFB option is allowed.' |
| 'LFB path reserved' | 'Indicates that the path for the call is reserved (national use).' |
| 'LFB not allowed' | 'Indicates that the LFB option is not allowed.' |
mlpp_pl_modes
| Value | Description |
|---|---|
| 'PL flash override' | 'Indicates that precedence level is flash override (highest).' |
| 'PL flash' | 'Indicates that precedence level is flash.' |
| 'PL immediate' | 'Indicates that precedence level is immediate.' |
| 'PL priority' | 'Indicates that precedence level is priority.' |
| 'PL routine' | 'Indicates that precedence level is routine (lowest).' |
call_transfer_modes
| Value | Description |
|---|---|
| 'Relay' | 'Relay call transfer requests from outgoing call leg to incoming call leg (don\'t process locally)' |
| 'Process' | 'Process call transfer (un-join outgoing call leg, route and join a new outgoing call leg...)' |
info_transfer_caps
| Value | Description |
|---|---|
| 'Speech' | 'Speech (val=0x00)' |
| 'Digital' | 'Unrestricted digital information (val=0x08)' |
| 'Restricted digital' | 'Restricted digital information (val=0x09)' |
| '3.1 kHz audio' | '3.1 kHz audio (val=0x10)' |
| 'Digital with tones' | 'Unrestricted digital information with tones/announcements (val=0x11)' |
| 'Video' | 'Video (val=0x18)' |
| 'Relay' | 'Relay information transfer capability from other leg' |
dtmf_types
| Value | Description |
|---|---|
| 'Relay DTMF according to RFC2833' | |
| 'Relay DTMF in band' | |
| 'Relay DTMF using SIP INFO messages' |
ring_tone_types
| Value | Description |
|---|---|
| 'Don\'t play any tone' | 'No call progress tone played' |
| 'Play ring tone' | 'Standard ring tone configured in profile' |
| 'Play busy tone' | 'Standard busy tone configured in profile' |
| 'Play fast busy (congestion) tone' | 'Standard congestion tone configured in profile' |
| 'Play a specific audio file' | 'Audio file or audio file list (example: @{PROMPT_PATH}/reason_404.wav:0:0:0)' |
cause_types
| Value | Description |
|---|---|
| 'Q850 unallocated number' | |
| 'Q850 no route to network' | |
| 'Q850 no route to destination' | |
| 'Q850 send special tone' | |
| 'Q850 misdialled trunk prefix' | |
| 'Q850 channel unacceptable' | |
| 'Q850 call awarded in established channel' | |
| 'Q850 preemption' | |
| 'Q850 reattempt' | |
| 'Q850 ported number' | |
| 'Q850 normal call clearing' | |
| 'Q850 user busy' | |
| 'Q850 no user responding' | |
| 'Q850 no answer from user' | |
| 'Q850 subscriber absent' | |
| 'Q850 call rejected' | |
| 'Q850 number changed' | |
| 'Q850 redirection' | |
| 'Q850 exchange routing error' | |
| 'Q850 non selected user clearing' | |
| 'Q850 destination out of order' | |
| 'Q850 address incomplete' | |
| 'Q850 facility rejected' | |
| 'Q850 response to status enquiry' | |
| 'Q850 normal unspecified' | |
| 'Q850 no circuit available' | |
| 'Q850 network out of order' | |
| 'Q850 frame mode out of service' | |
| 'Q850 frame mode connection operational' | |
| 'Q850 temporary failure' | |
| 'Q850 switching equipment congestion' | |
| 'Q850 access information discarded' | |
| 'Q850 circuit not available' | |
| 'Q850 precedence call blocked' | |
| 'Q850 resource unavailable' | |
| 'Q850 quality of service not available' | |
| 'Q850 requested facility not subscribed' | |
| 'Q850 outgoing calls barred' | |
| 'Q850 outgoing calls barred within CUG' | |
| 'Q850 incoming calls barred' | |
| 'Q850 incoming calls barred within CUG' | |
| 'Q850 bearer cap not authorized' | |
| 'Q850 bearer cap not available' | |
| 'Q850 inconsistency access info' | |
| 'Q850 service not available' | |
| 'Q850 bearer cap not implemented' | |
| 'Q850 channel type not implemented' | |
| 'Q850 requested facility not implemented' | |
| 'Q850 only restricted digital info' | |
| 'Q850 service not implemented' | |
| 'Q850 invalid call reference' | |
| 'Q850 channel does not exist' | |
| 'Q850 call identity does not exist' | |
| 'Q850 call identity in use' | |
| 'Q850 no call suspended' | |
| 'Q850 call has been cleared' | |
| 'Q850 user not member of CUG' | |
| 'Q850 incompatible destination' | |
| 'Q850 non existant CUG' | |
| 'Q850 invalid transit network' | |
| 'Q850 invalid message unspecified' | |
| 'Q850 mandatory IE missing' | |
| 'Q850 message type non existent' | |
| 'Q850 not compatible with call state' | |
| 'Q850 IE non existent' | |
| 'Q850 invalid IE content' | |
| 'Q850 message not compatible' | |
| 'Q850 recovery on timer expiry' | |
| 'Q850 parameter non existent passed on' | |
| 'Q850 msg with non recognized param discarded' | |
| 'Q850 protocol error' | |
| 'Q850 interworking unspecified' | |
| 'Toolpack normal' | |
| 'Toolpack resource error' | |
| 'Toolpack timeout' | |
| 'Toolpack no route' | |
| 'Toolpack call collision' | |
| 'Toolpack sync drop' | |
| 'Toolpack signaling error' | |
| 'Toolpack locally rejected' | |
| 'Toolpack interface not available' | |
| 'Toolpack reset in progress' | |
| 'Toolpack rejected by unit' | |
| 'Toolpack missing or invalid IE' | |
| 'Toolpack incoming only' | |
| 'Toolpack system configuration changed' | |
| 'Toolpack resource no more available' | |
| 'Toolpack incompatible media' | |
| 'Toolpack resource allocation failed' | |
| 'Toolpack data path not available' | |
| 'Toolpack local congestion' | |
| 'Toolpack authorization required' | |
| 'Toolpack call divert is not allowed' | |
| '300 Multiple Choices' | |
| '301 Moved Permanently' | |
| '302 Moved Temporarily' | |
| '305 Use Proxy' | |
| '380 Alternative Service' | |
| '400 Bad request' | |
| '401 Unauthorized' | |
| '402 Payment required' | |
| '403 Forbidden' | |
| '404 Not found' | |
| '405 Method not allowed' | |
| '406 Not acceptable' | |
| '407 Proxy authentication required' | |
| '408 Request timeout' | |
| '409 Conflict' | |
| '410 Gone' | |
| '413 Request entity too large' | |
| '414 Request URI too long' | |
| '415 Unsupported media' | |
| '416 Unsupported URI scheme' | |
| '420 Bad extension' | |
| '421 Extension required' | |
| '422 Session timer too small' | |
| '423 Interval too brief' | |
| '429 Referrer identity error' | |
| '480 Temporary unavailable' | |
| '481 Call or transaction does not exist' | |
| '482 Loop detected' | |
| '483 Too many hops' | |
| '484 Address incomplete' | |
| '485 Ambiguous' | |
| '486 Busy here' | |
| '487 Request terminated' | |
| '488 Not acceptable here' | |
| '489 Bad event' | |
| '491 Retry after' | |
| '500 Server internal error' | |
| '501 Not implemented' | |
| '502 Bad gateway' | |
| '503 Service unavailable' | |
| '504 Server timeout' | |
| '505 Version unsupported' | |
| '513 Message too large' | |
| '600 Busy everywhere' | |
| '603 Decline' | |
| '604 Not exist anywhere' | |
| '606 Not acceptable' |
reason_cause_actions
| Value | Description |
|---|---|
| 'Continue call' | |
| 'Stop call' | |
| 'Process call routing' |
channel_usages
| Value | Description |
|---|---|
| 'Round-Robin' | |
| 'Per-trunk lowest timeslot' | |
| 'Per-trunk highest timeslot' | |
| 'All-trunks lowest timeslot' | |
| 'All-trunks highest timeslot' | |
| 'Lowest CIC' | |
| 'Highest CIC' | |
| 'Odd lowest CIC' | |
| 'Odd highest CIC' | |
| 'Even lowest CIC' | |
| 'Even highest CIC' |
nap_types
| Value | Description |
|---|---|
| 'NAP type ISDN' | |
| 'NAP type SS7' | |
| 'NAP type SIP' | |
| 'NAP type VOIP media only' | |
| 'NAP type TDM media only' | |
| 'NAP type CAS' |
caf_timezones
| Value | Description |
|---|---|
| 'International Date Line West' | |
| 'Nome Time' | |
| 'Hawaii-Aleutian Standard Time' | |
| 'Hawaii-Aleutian Daylight Time' | |
| 'Pacific Standard Time' | |
| 'Pacific Daylight Time' | |
| 'Central Standard Time' | |
| 'Central Daylight Time' | |
| 'Atlantic Standard Time' | |
| 'Newfoundland Standard Time' | |
| 'Atlantic Daylight Time' | |
| 'Newfoundland Daylight Time' | |
| 'Azores Time' | |
| 'West Africa Time' | |
| 'Greenwich Mean Time' | |
| 'Central European Time' | |
| 'Eastern European Time' | |
| 'Moscow Standard Time' | |
| 'Moscow Daylight Time' | |
| 'Echo Time Zone' | |
| 'Foxtrot Time Zone' | |
| 'Christmas Island Time' | |
| 'Australian Western Standard Time' | |
| 'Australian Western Daylight Time' | |
| 'Australian Central Standard Time' | |
| 'Australian Eastern Standard Time' | |
| 'Australian Central Daylight Time' | |
| 'Australian Eastern Daylight Time' | |
| 'Norfolk (Island) Time' | |
| 'International Date Line East' | |
| 'Local timezone' |
uui_encodings
| Value | Description |
|---|---|
| 'Hex' | 'Use hexadecimal encoding' |
| 'Text' | 'Use text encoding if possible' |
| 'Escaped text' | 'Use text encoding, escape illegal characters' |
system_physical_ports
| Value | Description |
|---|---|
| 'eth0' | 'Port labeled eth0' |
| 'eth1' | 'Port labeled eth1' |
| 'voip0' | 'Port labeled voip0' |
| 'voip1' | 'Port labeled voip1' |
adapter_physical_port_purposes
| Value | Description |
|---|---|
| 'HOST' | 'HOST' |
| 'CTRL0' | 'CTRL0' |
| 'CTRL1' | 'CTRL1' |
| 'OTHER' | 'OTHER' |
bonding_switchovers
| Value | Description |
|---|---|
| 'One' | 'One IP address unreachable' |
| 'Half + 1' | 'Half + 1 IP addresses unreachable' |
| 'All' | 'All IP addresses unreachable' |
gateway_test_call_modes
| Value | Description |
|---|---|
| 'Generate outgoing call' | 'Generate an outgoing call that will not be subjected to the routing table.' |
| 'Simulate incoming call' | 'Will simulate an incoming call that will go through the routing table. This means that the call can be rejected or call parameters will be re-mapped according to the routing table before the outgoing call is made.' |
local_nat_traversal_methods
| Value | Description |
|---|---|
| 'None' | 'This is used when gateway is not NATted' |
| 'Force Public IP' | 'Forces the local public IP address in SIP and RTP packets.' |
| 'Advertise Active Direction' | 'Sends the \'a=direction:active\' in SDP attribute. Remote device must set itself in passive mode.' |
remote_nat_traversal_methods
| Value | Description |
|---|---|
| 'None' | 'Remote device is not behind a NAT or remote NAT device is SIP/RTP aware.' |
| 'Parse Direction Attribute' | 'Uses \'Passive Mode\' only when \'a=direction:active\' is received in the SDP.' |
| 'Force Passive Mode' | 'Use IP address and port from first received RTP packet to starts sending RTP packets.' |
non_linear_processor_tune_options
| Value | Description |
|---|---|
| 'Normal' | 'Default level of non-linear processing engagement of the echo cancellation module. This is the optimal setting for most call environment.' |
| 'Increased' | 'Increased level of non-linear processing engagement of the echo cancellation module. It may be required for some 2-to-4 wire hybrid or line conditions with large non-linear component in the echo.' |
| 'Reduced' | 'Reduced level of non-linear processing engagement of the echo cancellation module. It can avoid unpleasant voice artifact such as choppiness if there is heavy double-talk conditions while doing echo-tail characterization at the start of a call.' |
| 'Disabled' | 'Disable the non-linear processing of the echo cancellation module. It should always be activated unless while testing some G.168 scenarios.' |
voip_packet_durations
| Value | Description |
|---|---|
| '5 ms' | 'Use packet duration of 5ms' |
| '10ms' | 'Use packet duration of 10ms' |
| '20ms' | 'Use packet duration of 20ms' |
| '30ms' | 'Use packet duration of 30ms' |
| '40ms' | 'Use packet duration of 40ms' |
| '50ms' | 'Use packet duration of 50ms' |
| '60ms' | 'Use packet duration of 60ms' |
| '70ms' | 'Use packet duration of 70ms' |
| '80ms' | 'Use packet duration of 80ms' |
| '90ms' | 'Use packet duration of 90ms' |
| '160ms' | 'Use packet duration of 160ms' |
host_types
| Value | Description |
|---|---|
| 'None' | 'No application will be launch automatically on this host' |
| 'Management' | 'Indicates that this host will run management applications. There should be one or two hosts with that option.' |
| 'Call' | 'Indicates that this host will run call control applications. There should be one or two hosts with that option.' |
| 'Streamserver' | 'Indicates that this host will run stream server application. There can be multiple hosts with this option (stream server is used in load-sharing mode)' |
| 'Faxserver' | 'Indicates that this host will run faxserver application.' |
host_control_upload_action_types
| Value | Description |
|---|---|
| 'None' | 'This action is used when there is no upload.' |
| 'Upload Toolpack Package' | 'This action is used when uploading a toolpack package.' |
| 'Upload License' | 'This action is used when uploading a license.' |
| 'Upload OS package' | 'This action is used when uploading an Operating System package.' |
trace_levels
| Value | Description |
|---|---|
| 'Level 0 (loud)' | |
| 'Level 1' | |
| 'Level 2' | |
| 'Level 3' | |
| 'Level 4 (quiet)' | |
| 'Msg and errors only' | |
| 'Errors only' |
trace_submodule_types
| Value | Description |
|---|---|
| 'None' | |
| 'Base' | |
| 'Db' | |
| 'Dao' | |
| 'Service' | |
| 'Cmc' | |
| 'Call' | |
| 'Ivr' | |
| 'Gw' | |
| 'Comm' | |
| 'Cli' | |
| 'Oam' | |
| 'Alm' | |
| 'Cm' | |
| 'Udm' | |
| 'Syslog' | |
| 'TbLogTrace' | |
| 'User defined 0' | |
| 'User defined 1' | |
| 'User defined 2' | |
| 'User defined 3' | |
| 'User defined 4' | |
| 'User defined 5' | |
| 'User defined 6' | |
| 'User defined 7' | |
| 'User defined 8' | |
| 'User defined 9' | |
| 'User defined 10' | |
| 'User defined 11' | |
| 'User defined 12' | |
| 'User defined 13' | |
| 'User defined 14' | |
| 'User defined 15' |
hostlib_flow_modes
| Value | Description |
|---|---|
| 'Active' | |
| 'Low stress' |
application_types
| Value | Description |
|---|---|
| 'User-specific' | 'User-specific application (application not provided with the Toolpack package).' |
| 'TBOAM application' | 'OAM application, responsible for system operation and maintenance.' |
| 'Toolpack Sys Manager' | 'System manager application, responsible to apply system configuration.' |
| 'Toolpack Engine' | 'Engine application, responsible to receive and to make calls (signaling and media).' |
| 'Stream server' | 'Stream server application, responsible to play and record audio files during calls.' |
| 'Gateway' | 'Gateway application, responsible for call routing and managing various call flow options.' |
| 'Web server' | 'Web Portal, responsible to provide the Web interface to configure the system and view its status.' |
| 'Fax server' | 'Faxserver application, responsible to send and receive Faxes from tiff files.' |
| 'TbLogTrace' | 'Log trace application, responsible to log traces to log files on the host\'s disk.' |
| 'TbDebug' | 'Debug application, responsible to capture debug information from the system.' |
| 'TbUctWriter' | 'UCT writer application, responsible to write UCT (unified call trace) logs to disk (similar to CDR, but more detailed for debugging call flows).' |
| 'TbSnmpAgent' | 'SNMP agent application, responsible to respond to SNMP requests.' |
app_oam_target_states
| Value | Description |
|---|---|
| 'Dont run' | |
| 'Management' | |
| 'Run' | |
| 'Fault' |
app_oam_current_states
| Value | Description |
|---|---|
| 'Unknown' | |
| 'Not running' | |
| 'Starting' | |
| 'Ready' | |
| 'Shutting-down' | |
| 'Going management' | |
| 'Fault' |
app_ha_target_states
| Value | Description |
|---|---|
| 'Primary' | |
| 'Secondary' |
app_ha_current_states
| Value | Description |
|---|---|
| 'Not present' | |
| 'Active' | |
| 'Standby' |
streamserver_db_chunk_sizes
| Value | Description |
|---|---|
| '64KB' | |
| '128KB' | |
| '256KB' |
snmp_user_types
| Value | Description |
|---|---|
| 'None' | 'No authentication and no privacy check' |
| 'Authentication' | 'Authentication is mandatory and no privacy check' |
| 'Authentication and privacy' | 'Authentication and privacy are mandatory' |
snmp_authentication_types
| Value | Description |
|---|---|
| 'MD5' | 'Message-Digest algorithm 5' |
| 'SHA' | 'Secure Hash Algorithm key' |
snmp_privacy_protocols
| Value | Description |
|---|---|
| 'DES' | 'Data Encryption Standard' |
| 'AES' | 'Advanced Encryption Standard' |
snmp_versions
| Value | Description |
|---|---|
| 'SNMPv1' | 'SNMPv1 (RFC1155 and RFC1157)' |
| 'SNMPv2c' | 'SNMPv2c (RFC1901,RFC1907, RFC2578)' |
| 'SNMPv3' | 'SNMPv3 (RFC3411 and RFC3412)' |
tbgw_application_modes
| Value | Description |
|---|---|
| 'Normal' | |
| 'Voice mail' | |
| 'Call Back' | |
| 'H.248' |
tbgw_route_retry_timeout_modes
| Value | Description |
|---|---|
| 'Call Accepted' | |
| 'Call Progress Received' | |
| 'Call Alerted' | |
| 'Call Answered' |
tbgw_lawful_iri_upload_protocol_types
| Value | Description |
|---|---|
| 'FTP' | 'Upload IRI records using FTP (file transfer protocol)' |
| 'SFTP' | 'Upload IRI records using SFTP (secure file transfer protocol) - Password-less SSH authentication is required on Linux.' |
tbgw_lawful_iri_upload_modes
| Value | Description |
|---|---|
| 'Per-record' | 'Each file contains 1 IRI record' |
| 'Grouped' | 'Each file will regroup multiple IRI records (files are sent according to max size or time)' |
sip_port_types
| Value | Description |
|---|---|
| 'UDP' | |
| 'TCP' |
sip_privacy_types
| Value | Description |
|---|---|
| 'None' | 'Don\'t relay privacy information.' |
| 'Remote-Party-Id' | 'Send Remote-Party-ID header for relaying privacy information.' |
| 'P-Asserted-Identity' | 'Send headers from RFC3325 (Privacy, P-Asserted-Identity) for relaying privacy information.' |
| 'Both' | 'Send headers from RFC3325 (Privacy, P-Asserted-Identity) and Remote-Party-ID for relaying privacy information.' |
sip_ua_prov_resp_types
| Value | Description |
|---|---|
| 'Unsupported' | 'Do not advertise support of provisional ACK messages.' |
| 'Supported' | 'Advertise support of provisional ACK messages.' |
| 'Required' | 'Advertise support of provisional ACK messages and enforce their usage.' |
li_lengths
| Value | Description |
|---|---|
| 'Short' | 'Short mode is 200m (655 feet) - default' |
| 'Long' | 'Long mode is 685m (2250 feet)' |
| 'Manual' | 'Manual mode is for monitoring with signal level (advanced)' |
| 'Monitoring' | 'Monitoring mode is -20dB signal detection' |
li_signal_levels
| Value | Description |
|---|---|
| '0' | |
| '1' | |
| '2' | |
| '3' | |
| '4' | |
| '5' | |
| '6' | |
| '7' |
li_tx_states
| Value | Description |
|---|---|
| 'TX on' | 'Activates transmission (laser for STM-1/OC3 fiber, electric signal for DS3)' |
| 'TX off' | 'Deactivates transmission (laser for STM-1/OC3 fiber, electric signal for DS3) - It can be activated manually later with the status pages' |
li_section_trace_lengths
| Value | Description |
|---|---|
| '0' | |
| '1' | |
| '16' |
sonet_sdh_aps_channels
| Value | Description |
|---|---|
| 'Protection' | 'STM-1/OC3 protection channel - used when two fibers are connected to the same device' |
| 'Working channel 1' | 'Main STM-1/OC3 interace' |
sonet_sdh_aps_operation_modes
| Value | Description |
|---|---|
| 'Unidirectional' | 'If Tx or Rx fails, only one direction will switch to the protection STM-1/OC3' |
| 'Bidirectional' | 'Both Tx and RX will switch to the protection STM-1/OC3 if with Tx or Rx fails (default)' |
sonet_sdh_aps_switching_types
| Value | Description |
|---|---|
| 'Non revertive' | 'After a failure of the STM-1/OC3 link, the signal will stay on the protection channel even if the main link is qualified (up)' |
| 'Revertive' | 'After a failure of the STM-1/OC3 link, the signal will switch back on the main link if the main link is qualified (up)' |
sonet_sdh_aps_ber_thresh_levels
| Value | Description |
|---|---|
| '1x10^-3' | |
| '1x10^-4' | |
| '1x10^-5' | |
| '1x10^-6' | |
| '1x10^-7' | |
| '1x10^-8' | |
| '1x10^-9' |
e1_li_encodings
| Value | Description |
|---|---|
| 'HDB3' | |
| 'AMI' |
j1_li_encodings
| Value | Description |
|---|---|
| 'B8ZS' | |
| 'AMI' | |
| 'AMI CLEAR' |
t1_li_encodings
| Value | Description |
|---|---|
| 'B8ZS' | |
| 'AMI' | |
| 'AMI CLEAR' |
ds3_li_encodings
| Value | Description |
|---|---|
| 'B3ZS' |
ds3_li_lengths
| Value | Description |
|---|---|
| 'Short' | 'short mode is 138m (455 feet) - default' |
| 'Long' | 'long mode is 365m (1200 feet)' |
ds3_li_payload_types
| Value | Description |
|---|---|
| 'DS3' |
oc3_li_payload_types
| Value | Description |
|---|---|
| 'STS3' |
stm1_li_payload_types
| Value | Description |
|---|---|
| 'AU3' | 'Virtual container for 3 groups of 50Mbps' |
| 'AU4' | 'Single virtual container of 140Mbps ' |
li_loopback_types
| Value | Description |
|---|---|
| 'None' | 'Normal mode' |
| 'Line' | 'Entire signal received is sent back to remote end - Signal quality must be checked on the remote end' |
| 'Local' | 'Entire signal is loopback internally - uncommon to use this mode' |
ls_loopback_types
| Value | Description |
|---|---|
| 'None' | 'No Loopback - normal mode' |
| 'Line' | 'Line Loopback: The received Line signal is forwarded back to sender' |
| 'Payload' | 'Payload loopback: The received line signal is de-framed, framed and forwarded back to sender' |
| 'Local' | 'Internal loopback' |
| 'LOS' | 'Generate Loss of Signal on the Line: used to force a line down without de-allocating it' |
ds3_ls_framings
| Value | Description |
|---|---|
| 'M23' | 'Framing = 7xDS2 -> 4xDS1 (also called M13)' |
| 'CBIT' | 'Framing = C-bit parity' |
sts1_ls_payload_types
| Value | Description |
|---|---|
| 'VT2' | 'Payload Type = Virtual Tributary 2, 2Mbps (used for E1)' |
| 'VT15' | 'Payload Type = Virtual Tributary 1.5, 1.5Mbps (Used for T1/DS1)' |
| 'DS3' | 'Payload Type = DS3, 45Mbps' |
vt2_ls_payload_types
| Value | Description |
|---|---|
| 'E1' | ' Payload Type = E1' |
vt15_ls_payload_types
| Value | Description |
|---|---|
| 'T1' | 'Payload Type = T1/DS1' |
| 'J1' | 'Payload Type = J1' |
vc4_ls_payload_types
| Value | Description |
|---|---|
| 'TU3' | 'Payload Type = Tibutary Unit Group 3, for use with DS3 framing' |
| 'TU12' | 'Payload Type = Tributary Unit 12, for use with E1' |
| 'TU11' | 'Payload Type = Tributary Unit 11, for use with T1' |
vc3_ls_payload_types
| Value | Description |
|---|---|
| 'TU12' | 'Payload Type = Tributary Unit 12, for use with E1' |
| 'TU11' | 'Payload Type = Tributary Unit 11, for use with T1' |
| 'DS3' | 'Payload Type = DS3' |
vc12_ls_payload_types
| Value | Description |
|---|---|
| 'E1' | 'Payload Type = E1' |
| 'J1' | |
| 'T1' |
vc11_ls_payload_types
| Value | Description |
|---|---|
| 'T1' | 'Payload Type = T1' |
| 'J1' | 'Payload Type = J1' |
ds3_ls_payload_types
| Value | Description |
|---|---|
| 'Unchannelized' | |
| 'E1' | 'Payload Type = E1' |
| 'T1' | 'Payload Type = T1' |
| 'J1' | 'Payload Type = J1' |
ds3_ls_ais_det_algos
| Value | Description |
|---|---|
| '1010' | 'Alarm Indication Signal is detected with 1010 pattern' |
| 'CBIT' | 'Alarm Indication Signal is detected when all stuffing indicator C-bits equal zero' |
| 'CBIT and 1010' | 'Alarm Indication Signal is detected when all stuffing indicator C-bits equal zero and 1010 pattern' |
| 'All ones' | 'Alarm Indication Signal is detected with 1111 pattern' |
| 'Unframed ones' | 'Alarm Indication Signal is detected on unframed all-ones pattern' |
ds3_ls_oof_det_algos
| Value | Description |
|---|---|
| '3 out of 8 Fbits' | 'Out Of Frame is detected when 3 out of 8 F bits in error' |
| '3 out of 8 Fbits or 3 out of 4 consecutive MBits' | 'Out Of Frame is detected when 3 out of 8 F bits in error or 1 or more M bits in 3 of 4 consecutive frames in error' |
| '3 out of 16 Fbits' | 'Out Of Frame is detected when 3 out of 16 F bits in error' |
| '3 out of 16 Fbits or 3 out of 4 consecutive MBits' | 'Out Of Frame is detected when 3 out of 16 F bits in error or 1 or more M bits in 3 of 4 consecutive frames in error' |
ls_path_trace_lengths
| Value | Description |
|---|---|
| '0' | |
| '1' | |
| '16' | |
| '64' |
ls_ais_states
| Value | Description |
|---|---|
| 'On' | |
| 'Off' |
ls_c2_path_signal_labels
| Value | Description |
|---|---|
| 'Unequipped' | |
| 'Equiped non-specific' | |
| 'Virtual tributaries mapped asynchronously' | |
| 'Asynchronous DS3 mapping' |
ls_v5_path_signal_labels
| Value | Description |
|---|---|
| 'Unequipped' | |
| 'Equiped non-specific' | |
| 'Virtual tributaries mapped asynchronously' |
ls_channel_mapping_modes
| Value | Description |
|---|---|
| 'KLM' | 'Linear channel assignation (default)' |
| 'ITU-T' | 'ITU-T channel assignation (0-21-42-3-24-45-6-27-48-9-...)' |
| 'ALCATEL' | 'Alcatel channel assignation (0-7-14-1-8-15-2-9-16-3-...)' |
e1_ls_framings
| Value | Description |
|---|---|
| 'STD' | 'Framing = No CRC' |
| 'MFRAME' | 'Framing = with CRC' |
| 'AUTO' | 'Framing is auto selected between CRC and No-CRC' |
t1_ls_framings
| Value | Description |
|---|---|
| 'SF' | 'Framing = Superframe' |
| 'ESF' | 'Framing = Extended Superframe' |
| 'SLC96' | 'Framing = SLC96 mode' |
j1_ls_framings
| Value | Description |
|---|---|
| 'SF' | 'Framing = Superframe' |
| 'ESF' | 'Framing = Extended Superframe' |
| 'SLC96' | 'Framing = SLC96 mode' |
stack_types
| Value | Description |
|---|---|
| 'Isdn' | |
| 'Mtp2' | |
| 'Isup' | |
| 'NAP' | |
| 'Casr2' | |
| 'Lapd' |
isdn_d_channel_statuses
| Value | Description |
|---|---|
isdn_b_channel_main_statuses
| Value | Description |
|---|---|
isdn_b_channel_call_statuses
| Value | Description |
|---|---|
isdn_variants
| Value | Description |
|---|---|
| '4ESS' | 'TR41459 (Lucent 4ESS, 5ESS)' |
| 'AUS' | 'Australia TS-038 and TS-014' |
| '5ESS' | 'TR41459 (Lucent 4ESS, 5ESS)' |
| 'NET5' | 'EuroISDN ETSI DSS1 TBR4 including deltas for France,Germany,Italy,Portugal,Sweden,U.K and others ' |
| 'DMS' | 'Nortel DMS-100/250 (NIS A211-1 BCS 36)' |
| 'NI2' | 'National ISDN-2' |
| 'HONG-KONG' | 'Hong Kong CR13, HKTA 2015 and HKTA 2027' |
| 'JAPAN INS' | 'Japan NTT INSNet1500' |
isdn_sides
| Value | Description |
|---|---|
| 'User' | 'Customer premises-side' |
| 'Network' | 'Central office side' |
isdn_variant_defaults
| Value | Description |
|---|---|
isdn_coding_standards
| Value | Description |
|---|---|
| 'ITU' | |
| 'ISO' | |
| 'National' | |
| 'Location Specific' |
isdn_locations
| Value | Description |
|---|---|
| 'User' | |
| 'Private Network Serving Local User' | |
| 'Public Network Serving Local User' | |
| 'Transit Network' | |
| 'Public Network Serving Remote User' | |
| 'Private Network Serving Remote User' | |
| 'Network Beyond Interworking Point' |
bits_port_types
| Value | Description |
|---|---|
| 'E1' | 'E1 line type' |
| 'T1' | 'T1 line type' |
bits_port_e1_lengths
| Value | Description |
|---|---|
| 'Short' | 'short mode is 200m (655 feet) - default' |
| 'Long' | 'long mode is 685m (2250 feet)' |
bits_port_e1_line_encodings
| Value | Description |
|---|---|
| 'HDB3' | 'HDB3 line encoding' |
| 'AMI' | 'AMI line encoding' |
bits_port_t1_lengths
| Value | Description |
|---|---|
| 'Short' | 'short mode is 200m (655 feet) - default' |
| 'Long' | 'long mode is 685m (2250 feet)' |
bits_port_t1_line_encodings
| Value | Description |
|---|---|
| 'B8ZS' | 'B8ZS line encoding' |
| 'AMI' | 'AMI line encoding' |
system_clock_ref_types
| Value | Description |
|---|---|
| 'Local oscillator' | 'Use internal oscillator as clock source (master)' |
| 'Line service' | 'Use line service as clock source' |
| 'Sonet SDH' | 'Use SONET/SDH line interface as clock source' |
| 'Bits port' | 'Use BITS port line interface as clock source' |
clock_ref_types
| Value | Description |
|---|---|
| 'None' | 'No clock source' |
| 'Local oscillator' | 'Internal oscillator as clock source' |
| 'Trunk' | 'Trunk line/service interface as clock source' |
| 'MBL' | 'TMS port interface as clock source' |
| 'Bits port' | 'BITS port line interface as clock source' |
| 'Sonet SDH' | 'SONET/SDH line interface as clock source' |
mtp2_timeslot_rates
| Value | Description |
|---|---|
| '64Kbps' | '0xFF timeslot mask' |
| '56Kbps' | '0x7F timeslot mask' |
| '48Kbps' | '0x7E timeslot mask' |
mtp2_protocol_types
| Value | Description |
|---|---|
| 'ITU88' | 'ITU blue book' |
| 'ITU92' | 'ITU white book. Used for ITU92, ITU97, Q767, SINGAPORE, CHINA' |
| 'ANSI88' | 'Used for ANSI88' |
| 'ANSI92' | 'Used for ANSI92, ANSI96 and TELCORDIA' |
| 'TTC' | 'Used for TTC' |
| 'NTT' | 'Used for NTT' |
ss7_dpc_lengths
| Value | Description |
|---|---|
| '14bits format=3.8.3' | 'Default ITU configuration' |
| '16bits format=7.4.5' | 'Default TTC and NTT configuration' |
| '24bits format=8.8.8' | 'Default ANSI and CHINA configuration' |
mtp2_connection_modes
| Value | Description |
|---|---|
| 'Normal' | 'Low speed link (one timeslot) or VSL (several consecutive timeslots)' |
| 'HSL' | 'High speed link (all timeslots)' |
mtp2_itu_ansi_error_corrections
| Value | Description |
|---|---|
| 'Normal' | 'Normal error correction type' |
| 'Cyclical' | 'Preventative cyclical error correction type' |
mtp2_datatlink_states
| Value | Description |
|---|---|
| 'Enabled' | 'Data link state UP' |
| 'Disabled' | 'Data link state DOWN' |
m2pa_protocol_types
| Value | Description |
|---|---|
| 'ITU' | 'Used for ITU specification' |
| 'ANSI' | 'Used for ANSI specification' |
| 'TTC' | 'Used for TTC specification' |
m2ua_node_types
| Value | Description |
|---|---|
| 'Signaling Gateway (SG)' | 'Signaling gateway. (mtp2 to m2ua)' |
| 'Application Server Process (ASP)' | 'MGC mode initiates and establishes the communication with the SG. (m2ua to mtp3)' |
| 'ASP with m2ua-mtp2 relay' | 'Relay mode initiates and establishes the communication with the SG. (m2ua to mtp2)' |
m2ua_traffic_modes
| Value | Description |
|---|---|
| 'ACTIVE_STANDBY' | 'Traffic mode type (over-ride)' |
| 'LOADSHARE' | 'Traffic mode type (Load share)' |
| Value | Description |
|---|---|
| 'ROUND_ROBIN' | 'Load share mode Round robin' |
| 'PER_LINK' | 'Load share mode per link' |
m2ua_protocol_types
| Value | Description |
|---|---|
| 'ITU' | 'Used for ITU specification' |
| 'ANSI' | 'Used for ANSI specification' |
| 'TTC' | 'Used for TTC specification' |
m2ua_intf_id_types
| Value | Description |
|---|---|
| 'Integer' | 'Interface ID is an integer' |
| 'String' | 'Interface ID is a string' |
m2ua_target_link_states
| Value | Description |
|---|---|
| 'Connected' | 'Link state connected' |
| 'Disconnected' | 'Link state disconnected' |
m2ua_target_peer_states
| Value | Description |
|---|---|
| 'None' | 'Peer state none' |
| 'Init' | 'Peer state init' |
| 'Asp-up' | 'Peer state asp-up' |
| 'Asp-Active' | 'Peer state asp-active' |
| 'Abort' | 'Peer state abort' |
| 'Shutdown' | 'Peer state shutdown' |
m3ua_node_types
| Value | Description |
|---|---|
| 'Signaling Gateway Process (SGP)' | 'Signaling gateway' |
| 'Application Server Process (ASP)' | 'ASP is generally a soft switch' |
| 'IP Server Process (IPSP)' | 'Point to point connection' |
m3ua_protocol_types
| Value | Description |
|---|---|
| 'ITU' | 'Used for ITU specification' |
| 'ANSI' | 'Used for ANSI specification' |
| 'CHINA' | 'Used for CHINA specification' |
| 'TTC' | 'Used for TTC specification' |
| 'NTT' | 'Used for NTT specification' |
m3ua_subservice_field_types
| Value | Description |
|---|---|
| 'International' | 'Network indicator: International (ssf=0)' |
| 'National' | 'Network indicator: National (ssf=2)' |
| 'National-Reserved' | 'Network indicator: National reserved (ssf=3)' |
| 'Inter. Reserved' | 'Network indicator: International reserved (ssf=1)' |
m3ua_sls_ranges
| Value | Description |
|---|---|
| '4 bits' | 'SLS range for ITU and CHINA' |
| '5 bits' | 'SLS 5 bits range for ANSI, TTC and NTT' |
| '8 bits' | 'SLS 8 bits range for ANSI' |
m3ua_load_sharing_modes
| Value | Description |
|---|---|
| 'Round Robin' | 'Load share mode Round robin' |
| 'SLS' | 'Load share mode SLS selection' |
m3ua_asp_id_modes
| Value | Description |
|---|---|
| 'None' | 'No ASP Id validation or insertion' |
| 'Rx' | 'ASP Id needs to be present in ASPUP messages' |
| 'Tx' | 'Send ASP Id in ASPUP messages' |
| 'Rx+Tx' | 'ASP Id needs to be present in ASPUP messages and it is sent in ASPUP messages' |
m3ua_psp_modes
| Value | Description |
|---|---|
| 'Active-Standby' | 'Traffic mode type (over-ride)' |
| 'Load share' | 'Traffic mode type (Load share)' |
m3ua_psp_target_states
| Value | Description |
|---|---|
| 'Default' | 'Default target state (try to bring everything up)' |
| 'Asp-Up' | 'Try to bring the association up' |
| 'Asp-Down' | 'Try to bring the association down' |
| 'Abort' | 'Send abort message on the association every time remote peer attempts to bring the association up' |
| 'Shutdown' | 'Send shutdown message on the association every time remote peer attempts to bring the association up' |
m3ua_route_types
| Value | Description |
|---|---|
| 'Local' | 'The route leads to a local user' |
| 'Mtp3' | 'The route leads to the MTP3 (only valid at an SG)' |
| 'Psrv' | 'The route leads to a Peer Server' |
m3ua_sio_types
| Value | Description |
|---|---|
| 'None' | 'Unknown service' |
| 'Sccp' | 'SCCP service' |
| 'Isup' | 'ISUP service' |
mtp3_signaling_point_types
| Value | Description |
|---|---|
| 'SP' | 'MTP3 layer is used as an SP (signaling point) in the SS7 network' |
| 'STP' | 'MTP3 layer is used as an STP (signaling transfer point) in the SS7 network. This option is used when MTP3 forwards message from one DPC to an other DPC' |
mtp3_sub_service_fields
| Value | Description |
|---|---|
| 'International' | 'Network indicator: International (ssf=0)' |
| 'National' | 'Network indicator: National (ssf=2)' |
| 'Nat. Reserved' | 'Network indicator: National reserved (ssf=3)' |
| 'Inter. Reserved' | 'Network indicator: International reserved (ssf=1)' |
mtp3_dpc_states
| Value | Description |
|---|---|
| 'Inaccessible' | 'Point code is inaccessible (DOWN)' |
| 'Accessible' | 'Point code is accessible (UP)' |
| 'Congested' | 'Point code is in congestion' |
mtp3_link_types
| Value | Description |
|---|---|
| 'ANSI' | 'Used for ANSI88 and ANSI92' |
| 'ITU' | 'Used for ITU88, ITU92, ITU97, Q767, SINGAPORE, UK, ETSI and ETSIV3' |
| 'CHINA' | 'Used for CHINA' |
| 'ANSI96' | 'Used for ANSI96 and TELCORDIA' |
mtp3_restart_procedures
| Value | Description |
|---|---|
| 'None' | 'Restart procedure is disabled' |
| 'ITU88' | 'ITU88 restart procedure is applied by default to links, linksets and routes. ISUP and SCCP messages are dropped until the restart is completed' |
| 'ITU92' | 'ITU92 restart procedure is applied by default to links, linksets and routes. ISUP and SCCP messages are dropped until the restart is completed' |
| 'ANSI' | 'ANSI restart procedure is applied by default to links, linksets and routes. ISUP and SCCP messages are dropped until the restart is completed' |
mtp3_route_directions
| Value | Description |
|---|---|
| 'OPC' | 'Originating (local) point code' |
| 'DPC' | 'Destination (remote) point code' |
mtp3_priorities
| Value | Description |
|---|---|
| 'Priority 0' | 'Highest priority for link or linkset. There must be at least one link in a linkset with priority 0' |
| 'Priority 1' | 'Priority for link or linkset. Priority 1 is used only when all links with priority 0 are DOWN' |
| 'Priority 2' | 'Priority for link or linkset. Priority 2 is used only when all links with priority 1 are DOWN' |
| 'Priority 3' | 'Lowest priority for link or linkset. Priority 3 is used only when all links with priority 2 are DOWN' |
mtp3_messages_priorities
| Value | Description |
|---|---|
| 'None' | 'Specifies the priority at which MTP3 management messages are sent, in case the network allows priorities to be set in mtp3 message header.' |
| 'Priority 0' | 'Priority 0 is used for messages in service information octet (sub service field priority bits).' |
| 'Priority 1' | 'Priority 1 is used for messages in service information octet (sub service field priority bits).' |
| 'Priority 2' | 'Priority 2 is used for messages in service information octet (sub service field priority bits).' |
| 'Priority 3' | 'Priority 3 is used for messages in service information octet (sub service field priority bits).' |
mtp3_bind_link_types
| Value | Description |
|---|---|
| 'MTP2' | 'MTP3 link is using a MTP2 link' |
| 'M2PA' | 'MTP3 link is using a M2PA link' |
| 'M2UA' | 'MTP3 link is using a M2UA link' |
mtp3_sls_ranges
| Value | Description |
|---|---|
| 'ITU' | 'SLS range for ITU and CHINA' |
| 'ANSI 5 bits' | 'SLS 5 bits range for ANSI' |
| 'ANSI 8 bits' | 'SLS 8 bits range for ANSI' |
| 'NTT' | 'SLS range for NTT' |
isup_options
| Value | Description |
|---|---|
| 'No confusion' | 'Do not send confusion (CFN) message, forward to engine unrecognized MSUs.' |
| 'CGB Accept extra status byte' | 'Do not reject group message (CGB, CGBA, CGU, CGUA) when using too many bytes in status field' |
| 'Extra called number bytes' | 'Redefine the maximum called number IE size from 16 digits to 30 digits' |
| 'Extra calling number bytes' | 'Redefine the maximum calling number IE size from 16 digits to 30 digits' |
| 'Event information accept all values' | 'Do not block any value from the Event information IE, bypass ERROR:Event information' |
| 'ANSI charge number without originating line information' | 'ANSI 92 and 95. Do not block charge number IE if Originating Line Information IE is not present' |
| 'Support extra bytes after end of optional part' | 'Support extra bytes after end of optional part in ISUP message, bypass ERROR:Incorrect message length' |
| 'Support a range of 32 circuits for group messages' | 'Allow to send and receive group messages with a range and status IE of 32 circuits' |
isup_bind_network_types
| Value | Description |
|---|---|
| 'MTP3' | 'ISUP network is using a MTP3 network' |
| 'M3UA' | 'ISUP network is using a M3UA network' |
isup_protocol_variants
| Value | Description |
|---|---|
| 'ANSI88' | 'Used for ANSI88 specification' |
| 'ANSI92' | 'Used for ANSI92 specification' |
| 'ANSI95' | 'Used for ANSI95 specification' |
| 'TELCORDIA' | 'Used for BELLCORE specification' |
| 'ITU' | 'Used for ITU specification' |
| 'ITU97' | 'Used for ITU97 specification' |
| 'SINGAPORE' | 'Used for SINGAPORE specification' |
| 'Q767' | 'Used for Q767 specification' |
| 'NTT' | 'Used for NTT specification' |
| 'CHINA' | 'Used for CHINA specification' |
| 'ETSI' | 'Used for ETSI specification' |
| 'ETSIV3' | 'Used for ETSI V3 specification' |
| 'UK' | 'Used for UK specification' |
| 'SPIROU' | 'Used for Spirou specification' |
| 'RUSSIA' | 'Used for Russia specification' |
isup_address_indicator_types
| Value | Description |
|---|---|
| 'Not present' | 'Not present (val=1)' |
| 'Subscriber number' | 'Subscriber number (val=1)' |
| 'National number' | 'National (val=3)' |
| 'International number' | 'International (val=4)' |
isup_numbering_plans
| Value | Description |
|---|---|
| 'Unknown' | 'Unknown (val=1)' |
| 'ISDN' | 'ISDN (val=1)' |
| 'Telephony' | 'Telephony (val=2)' |
| 'Data' | 'Data (val=3)' |
| 'Telex' | 'Telex (val=4)' |
| 'National' | 'National (val=1)' |
| 'Private' | 'Private (val=5)' |
| 'Reserved' | 'Extension (val=1)' |
isup_release_locations
| Value | Description |
|---|---|
| 'User' | 'User (val=0)' |
| 'Private network LU' | 'Private network serving the local user (val=1)' |
| 'Public network LU' | 'Public network serving the local user (val=2)' |
| 'Transit network' | 'Transit network (val=3)' |
| 'Public network RU' | 'Public network serving the remote user (val=4)' |
| 'Private network RU' | 'Private network serving the remote user (val=5)' |
| 'Local interface' | 'Local interface (val=6)' |
| 'International network' | 'International network (val=7)' |
| 'Network beyond interworking point' | 'Network beyond interworking point (val=10)' |
| 'No info' | 'No information available (val=15)' |
| 'Relay' | 'Relay release location from other leg' |
isup_trunk_types
| Value | Description |
|---|---|
| 'E1' | 'E1 line service' |
| 'T1' | 'T1 line service' |
| 'J1' | 'J1 line service' |
isup_pause_actions
| Value | Description |
|---|---|
| 'Clear all' | 'Clear all calls upon reception of PAUSE (DPC unavailable)' |
| 'Clear transient' | 'Clear all transient calls upon reception of PAUSE (DPC unavailable)' |
| 'Clear after timer' | 'Clear calls only after a pause timer expires' |
isup_multirate_table_checks
| Value | Description |
|---|---|
| 'Table 3 Part 1' | 'Validate the start cic for mrate calls as per Table 3 part 1 Q.763' |
| 'Table 3 Part 2' | 'Validate the start cic for fixed contigous calls as per Table 3 part 2 Q.763' |
isup_sls_selectors
| Value | Description |
|---|---|
| 'Load distribution' | 'MTP3 header SLS selection by load distribution' |
| 'By CIC' | 'MTP3 header SLS selection by CIC value, using this option avoid race condition when using the same CIC for 2 calls back to back' |
isup_sls_ranges
| Value | Description |
|---|---|
| '5 bits' | 'ANSI SLS range 5 bits (modulo 32)' |
| '8 bits' | 'ANSI SLS range 8 bits (modulo 256)' |
isup_call_controls
| Value | Description |
|---|---|
| 'Incoming' | 'Circuits are always controlled by the remote end' |
| 'Outgoing' | 'Circuits always control the remote end' |
| 'Bothway' | 'When ((OPC lower than DPC) and (CIC is odd)) the circuit controls the remote end; When ((OPC greater than DPC) and (CIC is even)) the circuit is controlled by the remote end' |
| 'Controlled' | 'The remote ISUP always controls the call' |
| 'Controlling' | 'The local ISUP always controls the call' |
isup_cic_mappings
| Value | Description |
|---|---|
| 'Linear' | 'Linear assignation between CIC and timeslot number.' |
| 'JTISUP' | 'Japanese Integrated SS7 ISUP mapping' |
isup_slot_opts
| Value | Description |
|---|---|
| 'Skip for contiguous multirate' | 'Used by ANSI95, ITU97 and ETSIv3' |
| 'Supports non contiguous multirate' | 'Used by ANSI95, ITU97 and ETSIv3' |
isup_cic_opts
| Value | Description |
|---|---|
| 'ANSI international' | 'Modify the maximum number of circuits to block,unblock or query from 24 to 32. Used by ANSI88,92,95 and Bellcore' |
| 'Use confusion message' | 'Send confusion (CFN) message when connection is not available.' |
| 'Circuit type analog' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Circuit type digital' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Circuit type analog digital' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Alarm carrier indicator software' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Alarm carrier indicator hardware' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Continuity check none' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Continuity check statistical' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
| 'Continuity check per call' | 'Used in circuit validation (CVR, CVT) messages. Used by ANSI88,92,95 and Bellcore' |
sccp_protocol_variants
| Value | Description |
|---|---|
| 'ANSI' | |
| 'ITU' | |
| 'CHINA' |
sccp_net_indicator_bit_types
| Value | Description |
|---|---|
| 'INTERNATIONAL' | |
| 'NATIONAL' |
sccp_bind_network_types
| Value | Description |
|---|---|
| 'MTP3' | |
| 'M3UA' |
sccp_route_protocol_variants
| Value | Description |
|---|---|
| 'ANSI88' | |
| 'ANSI92' | |
| 'TELCORDIA' | |
| 'ITU88' | |
| 'ITU92' | |
| 'ITU96' | |
| 'GSM0806' |
sccp_route_replic_modes
| Value | Description |
|---|---|
| 'DOMINANT' | 'In this mode, each backup node/subsystem is assigned a unique priority. The node/subsystem on this route is the primary node/subsystem and is selected as the preferred node/subsystem when accessible. On failure of the preferred node/subsystem the next higher priority available backup node/subsystem is selected as the preferred node/subsystem.' |
| 'LOADSHARE' | 'In this mode, each backup node/subsystem together with the node/subsystem configured on the route is assigned equal priority and load is distributed among nodes/subsystems on the basis of: 1) SLS for class1 traffic, and 2) in round-robin fashion for class 0 traffic. Loadshare mode is applicable in TELCORDIA only.' |
| 'DOMINANT_ALTERNATE' | 'This mode is significant only for class 0 traffic. In this mode, class 0 traffic is prevented from reaching an accessible but congested node. For class 1 traffic, this mode is same as DOMINANT mode. In this mode, each backup node/subsystem is assigned a unique priority. The node/subsystem configured on the route is selected as the primary node/subsystem and is the preffered node/subsystem when accessible and not congested. On failure or congestion of the preferred node/subsystem the next higher priority available and uncongested backup node/subsystem is selected as the preferred node/subsystem. This mode of operation is applicable only in ANSI96 and TELCORDIA.' |
| 'LOADSHARE_ALTERNATE' | 'This mode is significant only for class 0 traffic. In this mode, class 0 traffic is prevented from reaching an accessible, but congested node. For class 1 traffic, this mode is same as LOADSHARE mode. In this mode, each backup node/subsystem together with the node/subsystem configured on the route is assigned equal priority and load is distributed among nodes/subsystems on the basis of: 1) SLS for class 1 traffic, and 2) in round-robin fashion for class 0 traffic. For class 0 traffic, a node/subsystem is selected when it is accessible and uncongested. On failure or congestion of the node, next available and uncongested node/subsystem is selected. This mode of operation is applicable only in TELCORDIA.' |
sccp_route_sls_masks
| Value | Description |
|---|---|
| '5_BITS' | 'Networks Signalling Link Selection (SLS) is 5 bits (ANSI and TELCORDIA only).' |
| '8_BITS' | 'Networks SLS is 8 bits (ANSI and TELCORDIA only).' |
sccp_rt_opts
| Value | Description |
|---|---|
| 'ONLINE_BY_DEFAULT' | |
| 'TRANSLATOR_NODE' | |
| 'ADJACENT_NODE' | |
| 'INS_CAPABLE_NODE' |
sccp_ssn_opts
| Value | Description |
|---|---|
| 'ACCESSIBLE_BY_DEFAULT' | |
| 'NORMAL_ROUTED' |
sccp_gt_format_types
| Value | Description |
|---|---|
| 'NOT_USED' | 'Indicates that global title is not used.' |
| 'TYPE_1' | 'Odd/Even Type and Nature of Address Indicator (NAI).' |
| 'TYPE_2' | 'Translation Type (TT) value.' |
| 'TYPE_3' | 'Translation Type (TT) value, Numbering Plan (NP) and Encoding Scheme (ES).' |
| 'TYPE_4' | 'Translation Type (TT) value, Numbering Plan (NP), Encoding Scheme (ES) and Nature of Address Indicator (NAI).' |
sccp_gt_odd_even_types
| Value | Description |
|---|---|
| 'NOT_USED' | 'Indicates that odd even type indicator is not used (for GTT association config only).' |
| 'ODD' | 'Odd number of address signals.' |
| 'EVEN' | 'Even number of address signals.' |
sccp_gt_nat_of_addr_inds
| Value | Description |
|---|---|
| 'NOT_USED' | 'Indicates that nature of address indicator is not used (for GTT association config only).' |
| 'SUBSCRIBER' | 'Subscriber number.' |
| 'NATIONAL' | 'Nationally significant number.' |
| 'INTERNATIONAL' | 'Internationally significant number.' |
sccp_gt_numb_plan_types
| Value | Description |
|---|---|
| 'NOT_USED' | 'Indicates that numbering plan indicator is not used (for GTT association config only).' |
| 'UNKNOWN' | 'Unknown number type.' |
| 'ISDN' | 'ISDN/telephony numbering plan.' |
| 'TELEPHONY' | 'Telephony numbering plan. (Not valid in ITU96, ANSI96 and TELCORDIA).' |
| 'GENERIC' | 'Generic numbering plan. (for ITU96 only).' |
| 'DATA' | 'Data numbering plan.' |
| 'TELEX' | 'Telex numbering plan.' |
| 'MARITIME_MOBILE' | 'Maritime Mobile numbering plan.' |
| 'LAND_MOBILE' | 'Land Mobile numbering plan.' |
| 'ISDN_MOBILE' | 'ISDN Mobile numbering plan.' |
| 'PRIVATE' | 'Private network or network specific numbering plan (for ITU96, ANSI96 and TELCORDIA).' |
sccp_gt_enc_types
| Value | Description |
|---|---|
| 'NOT_USED' | 'Indicates that encoding type indicator is not used (for GTT association config only).' |
| 'UNKNOWN' | 'Unknown encoding type.' |
| 'BCD_ODD' | 'BCD Odd.' |
| 'BCD_EVEN' | 'BCD Even.' |
| 'NATIONAL_ES' | 'National specific ES (allowed only in ITU96).' |
sccp_gtt_action_types
| Value | Description |
|---|---|
| 'FIX' | 'Use fixed range of digits to match GT address.' |
| 'VARIABLE_ASCENDING' | 'Use variable number of digits in ascending order to match GT address.' |
| 'VARIABLE_DESCENDING' | 'Use variable number of digits in descending order to match GT address.' |
| 'GT_TO_PC' | 'Use digits in incoming GT as the point code for routing purposes. This type of GTT is used in ISNI.' |
| 'CONST' | 'Matches any digits. Always translate to a fixed address.' |
| 'INSERT_PC' | 'Insert DPC before incoming GTAI and change TT, ES and NAI, leaving GTAI unchanged. This action is for modifying calling party address at an international Gateway, when message is entering international network, originating from a national network and having calling address in national specific format with Generic Numbering Plan. DPC inserted is the point code of the international Gateway, having capability to translate back the international address format to national specific address in response message. The DPC inserted, need not be the self point code of the international Gateway modifying the calling party address.' |
| 'STRIP_PC' | 'If first six digits are self point code in international format, strip off first six digits from the GTAI. Then do the translation and replace TT, ES, and NAI. Examine the DPC of the translated address, if it is self, do translation of the resulting address again else message will be forwarded to DPC for further translation without changing GTAI of the called address.' |
sccp_routing_types
| Value | Description |
|---|---|
| 'GLOBAL_TITLE' | 'Routing should be based on the global title.' |
| 'SSN' | 'Routing should be based on the destination point code and the subsystem number.' |
sctp_service_types
| Value | Description |
|---|---|
| 'UDP' | 'Tunnel SCTP packets in UDP packets' |
| 'RAW_IP' | 'Use standard SCTP packets' |
| 'RAW_IP_PRIOR' | 'Use standard SCTP packets with priority optimisation (Do not use)' |
tcap_protocol_variants
| Value | Description |
|---|---|
| 'ANSI88' | |
| 'ANSI92' | |
| 'ANSI96' | |
| 'ITU88' | |
| 'ITU92' | |
| 'ITU96' | |
| 'ETSI96' |
lapd_timeslot_rates
| Value | Description |
|---|---|
| '64Kbps' | |
| '56Kbps' | |
| '48Kbps' |
lapd_variants
| Value | Description |
|---|---|
| 'CCITT' | |
| '4ESS' | |
| '5ESS' | |
| 'INSNET' | |
| 'AUSTRALIA' | |
| 'ETSI' | 'Equivalent to EDSS1' |
| 'BC303CSC' | |
| 'DMS' | 'Equivalent to Bellcore' |
| 'NATIONAL ISDN-2' | |
| 'BELLCORE' |
lapd_protocol_sides
| Value | Description |
|---|---|
| 'User' | |
| 'Network' |
iua_traffic_modes
| Value | Description |
|---|---|
| 'ACTIVE_STANDBY' | 'Traffic mode type (over-ride)' |
| 'LOADSHARE' | 'Traffic mode type (Load share)' |
| Value | Description |
|---|---|
| 'ROUND_ROBIN' | 'Load share mode Round robin' |
| 'PER_LINK' | 'Load share mode per link' |
iua_intf_id_types
| Value | Description |
|---|---|
| 'Integer' | |
| 'String' |
