Replace TMG3200 Standalone With Spare
From TBwiki
(Difference between revisions)
(Added Management IP config and software upgrade,) |
(Added version 2.9, added a configuration backup at the start) |
||
| Line 4: | Line 4: | ||
== Removing the Defective Unit == | == Removing the Defective Unit == | ||
| + | *If unit is still active, do a configuration backup: | ||
| + | **[[Toolpack:Database_Backup_C|Configuration backup v2.8 and v2.9]] | ||
| + | **[[Toolpack:Database_Backup_B|Configuration backup v2.7]] | ||
*Shutdown the TMG3200 | *Shutdown the TMG3200 | ||
*Disconnect from the PSTN network | *Disconnect from the PSTN network | ||
| Line 21: | Line 24: | ||
*[[TMG:Change_Management_IP_Address|Configure the Management IP address]] | *[[TMG:Change_Management_IP_Address|Configure the Management IP address]] | ||
*Connect to the web portal: '''http://[IP address]:12358''' | *Connect to the web portal: '''http://[IP address]:12358''' | ||
| − | **[[Toolpack:Host_Standalone_A|Set host role v2.8]] | + | **[[Toolpack:Host_Standalone_A|Set host role v2.8 and v2.9]] |
**[[Toolpack:Host_Standalone_B|Set host role v2.7]] | **[[Toolpack:Host_Standalone_B|Set host role v2.7]] | ||
*Install the license of the replacement unit | *Install the license of the replacement unit | ||
| − | **[[Toolpack:Uploading_a_License_B|Install License Procedure for v2.8]] | + | **[[Toolpack:Uploading_a_License_B|Install License Procedure for v2.8 and v2.9]] |
**[[Toolpack:Uploading_a_License_A|Install License Procedure for v2.7]] | **[[Toolpack:Uploading_a_License_A|Install License Procedure for v2.7]] | ||
*Upgrade this unit to the same version as the defective unit: [[Gateway_Upgrade|Software upgrade]] | *Upgrade this unit to the same version as the defective unit: [[Gateway_Upgrade|Software upgrade]] | ||
| Line 31: | Line 34: | ||
If a database backup is available,import database using the Web Portal Backup menu: | If a database backup is available,import database using the Web Portal Backup menu: | ||
| − | *[[Toolpack:Restoring_a_Database_Backup_C|Restoring Database Procedure for v2.8]] | + | *[[Toolpack:Restoring_a_Database_Backup_C|Restoring Database Procedure for v2.8 and v2.9]] |
*[[Toolpack:Restoring_a_Database_Backup_B|Restoring Database Procedure for v2.7]] | *[[Toolpack:Restoring_a_Database_Backup_B|Restoring Database Procedure for v2.7]] | ||
== Configuring the replacement unit == | == Configuring the replacement unit == | ||
If a database backup is not available, configure the system via the web portal: | If a database backup is not available, configure the system via the web portal: | ||
| − | *[[Web_Portal_Tutorial_Guide_v2. | + | *[[Web_Portal_Tutorial_Guide_v2.9|Web_Portal Tutorial Guide v2.9]] |
*[[Web_Portal_Tutorial_Guide_v2.8|Web_Portal Tutorial Guide v2.8]] | *[[Web_Portal_Tutorial_Guide_v2.8|Web_Portal Tutorial Guide v2.8]] | ||
| + | *[[Web_Portal_Tutorial_Guide_v2.7|Web_Portal Tutorial Guide v2.7]] | ||
| + | |||
[[Category:Gateway_OAM&P|Replace TMG3200 Standalone With Spare]] | [[Category:Gateway_OAM&P|Replace TMG3200 Standalone With Spare]] | ||
[[Category:Revise on Major]] | [[Category:Revise on Major]] | ||
Revision as of 09:41, 22 December 2015
Warning: This procedure will require some system downtime.
The replacement of a standalone TMG3200 is comprised of following steps:
Contents |
Removing the Defective Unit
- If unit is still active, do a configuration backup:
- Shutdown the TMG3200
- Disconnect from the PSTN network
- Disconnect from the VoIP network
- Disconnect from the Management network
- Remove the TMG3200 from the equipment rack
Installing the Replacement Unit
Refer to TMG3200 Installation guide
- Rack-mount the Replacement Unit
- Connect to the Management Interface
- Connect to the VoIP Network
- Connect to the PSTN Network
Starting Up the TMG3200
- Power up the TMG3200
- Configure the Management IP address
- Connect to the web portal: http://[IP address]:12358
- Install the license of the replacement unit
- Upgrade this unit to the same version as the defective unit: Software upgrade
Restoring the configuration to the replacement unit
If a database backup is available,import database using the Web Portal Backup menu:
Configuring the replacement unit
If a database backup is not available, configure the system via the web portal:
