Toolpack:Creating a CAS R2 NAP D

From TBwiki

(Difference between revisions)

Revision as of 12:10, 22 December 2015

Applies to version(s): v2.9.

Now that you have created a CAS stack, you must create a network access point, in order to finish configuring your system. A Network Access Point (NAP) represents the entry point to another network or destination peer.

To create a network access point (NAP):

1- Click NAPs in the navigation panel

2- Click Create New NAP

3- Configure the new NAP:

Enter a name for the NAP
Select a user-created profile, if not, select default
Click Create

4- Verify that the NAP was successfully created message appears

5- Associate a CAS R2 stack with the NAP:

Select an interface (the newly-created CAS R2 stack)
Click the "<<" button to add the interface to the list

6- Select a value for Channel Usage, to avoid call collision

Click Save

7- Verify that the "NAP was successfully updated" message appears

Path

/configurations/@[configuration_name]/naps/@[nap_name]

Parameters (text)

/configurations/@[configuration_name]/naps/@[nap_name]
cas_stacks            = [  ]
default_profile       = "default"
isdn_stacks           = [  ]
isup_cic_groups       = [  ]
line_services         = [  ]
name                  = "isdn_nap_00"
port_ranges           = [  ]
sip_transport_servers = [  ]

/configurations/@[configuration_name]/naps/@[nap_name]/call_rate_limiting
maximum_call_burst                  = 0
maximum_calls_per_second            = 0
maximum_simultaneous_incoming_calls = 0
maximum_simultaneous_outgoing_calls = 0
maximum_simultaneous_total_calls    = 0
processing_delay_high_threshold     = "3 seconds"
processing_delay_low_threshold      = "1 second"

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg
poll_remote_proxy           = true
proxy_address               = ""
proxy_port                  = 5060
proxy_port_type             = "UDP"

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg/advanced_parameters
183_triggers_call_progress           = false
map_any_response_to_available_status = true
privacy_type                         = "P-Asserted-Identity"

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg/authentication_parameters
ignore_realm    = false
password        = ""
realm           = ""
reuse_challenge = false
user            = ""

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg/filtering_parameters
filter_by_local_port    = true
filter_by_proxy_address = true

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg/network_address_translation
local_method  = ""
remote_method = "None"

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg/registration_parameters
address_to_register = ""
register_to_proxy   = false

/configurations/@[configuration_name]/naps/@[nap_name]/sip_cfg/sipi_parameters
append_f_to_outgoing_calls = false
call_progress_method       = "183 Call Progress"
content_type               = "itu-t"
enable                     = false
isup_protocol_variant      = "ITU"

/configurations/@[configuration_name]/naps/@[nap_name]/tdm_cfg
append_f_to_outgoing_calls                     = false
append_pound_to_outgoing_calls                 = false
channel_usage                                  = "Per-trunk lowest timeslot"
remove_trailing_f_or_pound_from_incoming_calls = true

/configurations/@[configuration_name]/naps/@[nap_name]/tdm_cfg/overlap_parameters
enable_overlap_receiving              = false
enable_overlap_sending                = false
overlap_receiving_expected_digits     = 0
overlap_receiving_inter_digit_timeout = "20 seconds"
overlap_receiving_timeout             = "0 millisecond"

/configurations/@[configuration_name]/naps/@[nap_name]/voip_media_only_cfg
nat_local_method = ""

Parameters (json)

{
  "call_rate_limiting" : {
    "maximum_call_burst" : 0,
    "maximum_calls_per_second" : 0,
    "maximum_simultaneous_incoming_calls" : 0,
    "maximum_simultaneous_outgoing_calls" : 0,
    "maximum_simultaneous_total_calls" : 0,
    "processing_delay_high_threshold" : "3 seconds",
    "processing_delay_low_threshold" : "1 second"
  },
  "cas_stacks" : [
  ],
  "default_profile" : "default",
  "isdn_stacks" : [
  ],
  "isup_cic_groups" : [
  ],
  "line_services" : [
  ],
  "name" : "@[nap_name]",
  "port_ranges" : [
  ],
  "sip_cfg" : {
    "advanced_parameters" : {
      "183_triggers_call_progress" : false,
      "map_any_response_to_available_status" : true,
      "privacy_type" : "P-Asserted-Identity"
    },
    "authentication_parameters" : {
      "ignore_realm" : false,
      "password" : "",
      "realm" : "",
      "reuse_challenge" : false,
      "user" : ""
    },
    "filtering_parameters" : {
      "filter_by_local_port" : true,
      "filter_by_proxy_address" : true
    },
    "network_address_translation" : {
      "local_method" : "",
      "remote_method" : "None"
    },
    "poll_remote_proxy" : true,
    "proxy_address" : "",
    "proxy_port" : 5060,
    "proxy_port_type" : "UDP",
    "registration_parameters" : {
      "address_to_register" : "",
      "register_to_proxy" : false
    },
    "sipi_parameters" : {
      "append_f_to_outgoing_calls" : false,
      "call_progress_method" : "183 Call Progress",
      "content_type" : "itu-t",
      "enable" : false,
      "isup_protocol_variant" : "ITU"
    }
  },
  "sip_transport_servers" : [
  ],
  "tdm_cfg" : {
    "append_f_to_outgoing_calls" : false,
    "append_pound_to_outgoing_calls" : false,
    "channel_usage" : "Per-trunk lowest timeslot",
    "overlap_parameters" : {
      "enable_overlap_receiving" : false,
      "enable_overlap_sending" : false,
      "overlap_receiving_expected_digits" : 0,
      "overlap_receiving_inter_digit_timeout" : "20 seconds",
      "overlap_receiving_timeout" : "0 millisecond"
    },
    "remove_trailing_f_or_pound_from_incoming_calls" : true
  },
  "voip_media_only_cfg" : {
    "nat_local_method" : ""
  }
}

Toolpack:Creating a CAS R2 NAP D

Revision as of 12:10, 22 December 2015

Applies to version(s): v2.9.

List of Parameters

Views

Personal tools

Navigation

Search

Toolbox