Creating a CAS NAP
From TBwiki
| This article applies to: | Product | Version |
| Tmedia | 2.9, 2.10, 3.0, 3.2 |
Now that you have created a CAS stack, you must create a network access point to finish configuring your system. A Network Access Point (NAP) represents the entry point to another network or destination peer.
To create a network access point (NAP):
1- Click NAPs in the navigation panel
2- Click Create New NAP
3- Configure the new NAP:
- Enter a name for the NAP
- Select a user-created profile, if not, select default
- Click Create
4- Verify that the NAP was successfully created message appears
5- Associate a CAS R2 stack with the NAP:
- Select an interface (the newly-created CAS R2 stack)
- Click the "<<" button to add the interface to the list
6- Select a value for Channel Usage, to avoid call collision
- Click Save
7- Verify that the "NAP was successfully updated" message appears
Path
/configurations/@[configuration_name]/naps/@[nap_name]
Parameters (text)
/configurations/mg_17_1_22_performance/naps/CASr1 cas_stacks = [ "CA005577_00", "CA005577_01" ] default_profile = "default" name = "CASr1" /configurations/mg_17_1_22_performance/naps/CASr1/call_rate_limiting maximum_call_burst = 0 maximum_calls_per_second = 0 maximum_simultaneous_incoming_calls = 0 maximum_simultaneous_outgoing_calls = 0 maximum_simultaneous_total_calls = 0 processing_delay_high_threshold = "0 millisecond" processing_delay_low_threshold = "0 millisecond" /configurations/mg_17_1_22_performance/naps/CASr1/tdm_cfg channel_usage = "All-trunks lowest timeslot" /configurations/mg_17_1_22_performance/naps/CASr1/tdm_cfg/overlap_parameters
Parameters (json)
{
"call_rate_limiting" : {
"maximum_call_burst" : 0,
"maximum_calls_per_second" : 0,
"maximum_simultaneous_incoming_calls" : 0,
"maximum_simultaneous_outgoing_calls" : 0,
"maximum_simultaneous_total_calls" : 0,
"processing_delay_high_threshold" : "3 seconds",
"processing_delay_low_threshold" : "1 second"
},
"cas_stacks" : [
],
"default_profile" : "default",
"isdn_stacks" : [
],
"isup_cic_groups" : [
],
"line_services" : [
],
"name" : "@[nap_name]",
"port_ranges" : [
],
"sip_cfg" : {
"advanced_parameters" : {
"183_triggers_call_progress" : false,
"map_any_response_to_available_status" : true,
"privacy_type" : "P-Asserted-Identity"
},
"authentication_parameters" : {
"ignore_realm" : false,
"password" : "",
"realm" : "",
"reuse_challenge" : false,
"user" : ""
},
"filtering_parameters" : {
"filter_by_local_port" : true,
"filter_by_proxy_address" : true
},
"network_address_translation" : {
"local_method" : "",
"remote_method" : "None"
},
"poll_remote_proxy" : true,
"proxy_address" : "",
"proxy_port" : 5060,
"proxy_port_type" : "UDP",
"registration_parameters" : {
"address_to_register" : "",
"register_to_proxy" : false
},
"sipi_parameters" : {
"append_f_to_outgoing_calls" : false,
"call_progress_method" : "183 Call Progress",
"content_type" : "itu-t",
"enable" : false,
"isup_protocol_variant" : "ITU"
}
},
"sip_transport_servers" : [
],
"tdm_cfg" : {
"append_f_to_outgoing_calls" : false,
"append_pound_to_outgoing_calls" : false,
"channel_usage" : "Per-trunk lowest timeslot",
"overlap_parameters" : {
"enable_overlap_receiving" : false,
"enable_overlap_sending" : false,
"overlap_receiving_expected_digits" : 0,
"overlap_receiving_inter_digit_timeout" : "20 seconds",
"overlap_receiving_timeout" : "0 millisecond"
},
"remove_trailing_f_or_pound_from_incoming_calls" : true
},
"voip_media_only_cfg" : {
"nat_local_method" : ""
}
}
