|
|
| (27 intermediate revisions by 5 users not shown) |
| Line 1: |
Line 1: |
| − | == Call Leg Definition ==
| + | TelcoBridges Toolpack framework offers two API layers to manipulate call legs and audio mixers (conferences). |
| − | The main mechanism through which the customer application controls the [[Toolpack]] system is via the management of call legs. The application creates a call leg (or more than one for conferencing and bridging) at the beginning of a call, then controls it through a simple, protocol-agnostic API. When a call is terminated, the call leg can be destroyed.
| + | |
| | | | |
| − | A call leg is represented by an instance of the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html CTBCMCLeg] class. It represents a full-duplex media resource and/or its associated signaling entity. Typical examples of call legs with signaling would be an [[SS7]] [[ISUP]] call with its associated [[Circuit identification code|CIC]] (mapped to a [[TDM]] interface such as a T1 [[timeslot]]) or a [[SIP]] call with its associated [[VOIP]] [[Voice codecs|codec]] resource (attached to an IP/UDP endpoint). A media-only call leg would represent a standalone TDM endpoint (such as a T1 timeslot) or a VOIP endpoint (VOIP codec resource attached to an IP/UDP endpoint). The section titled [[CAF:_Working_With_Call_Legs#Leg Creation| Leg Creation ]] will show how different types of call legs can be created.
| + | We recommend that developers use the CAF API layer, as it offers higher-level functionality which accelerate application development. |
| | | | |
| − | The CTBCMCLeg class allows a programmer to easily act upon the call leg to influence the signaling portion (e.g. accept, answer, terminate, etc) and to use the media portion as well (e.g play prompts, record voice, play or collect digits and tones).
| |
| | | | |
| − | Other member functions are available to retrieve (and change in some cases) the call leg attributes including the media profile (e.g. parameters to the media resource) or signaling information (e.g. protocol type, called and calling party numbers, etc). Joining/unjoining (connection/disconnection) of call legs is also a typical action handled by this class for ’gateway-type’ applications. It is important to note that this class is protocol-agnostic and can handle any type of supported call legs (e.g. SIP/VOIP, [[ISDN]], SS7, Media only, etc).
| + | == CMC API layer == |
| | | | |
| | + | The lower-level API is based on classes ''CTBCMCLeg'' and ''CTBCMCMixer''. These classes allow receiving leg or mixer events (answered, digit collected, terminating, etc.), and send requests to perform actions (answer, play, terminate, etc.). |
| | | | |
| − | ===== Caveats =====
| + | The following page explains how to work with CTBCMCLeg directly, for lower-level applications that don't want the convenience of the CAF Call framework |
| − | * Do not confuse a ''call leg'' with a ''call''. A ''call leg'' represents one full-duplex link to a party while a ''call'' represents the agglomeration of multiple (two or more) call legs. For example, a ''bridge'' is a form of ''call'' that uses two ''call legs''.
| + | |
| − | * Do not confuse the base class CTBCMCLeg with the class [https://docs.telcobridges.com/mediawiki/autodoc/class_t_b_c_a_f_1_1_c_t_b_c_a_f_call_leg.html CTBCAFCallLeg]. The later is an implementation class specialized to be used by the [https://docs.telcobridges.com/mediawiki/autodoc/class_t_b_c_a_f_1_1_i_t_b_c_a_f_call_flow.html ITBCAFCallFlow] interface when dealing with multiple legs. It is designed to represent a leg within a call. It cannot be instanciated as a standalone object without modifications to make it independent from the ITBCAFCallFlow interface.
| + | |
| − | * If the overall goal is to bridge two or more call legs together, then the programmer would be advised to use the [https://docs.telcobridges.com/mediawiki/autodoc/class_t_b_c_a_f_1_1_c_t_b_c_a_f_bridge.html CTBCAFBridge] class for leg creation instead of creating call legs manually. This class already deals with the issues of handling multiple legs simultaneously.
| + | |
| − | | + | |
| − | == Command Flow for Leg Actions in CAF ==
| + | |
| − | All actions requested on a leg are executed asynchronously. For each action '''DoSomething()''' on a leg, a corresponding '''OnDoSomethingResponse()''' event will be received on the leg once Toolpack starts processing the command. If the '''OnXXXResponse()''' function does not handle the response (the default implementation is empty) and the result of the action was a failure, the default error handling function '''OnLegError()''' will be called. Most of the actions executed on a leg can take variable time to complete. In these case, an extra event will be received on the leg once the action is complete ('''OnXXXResponse()''' is always called when Toolpack '''starts''' executing the action).
| + | |
| − | | + | |
| − | | + | |
| − | For example, to play a digit sequence, one would call '''PlayDigit()'''. It would then almost immediately receive the '''OnPlayDigitResponse()''' event indicating that Toolpack has received the command. At the same time this event is called, Toolpack will start playing the digits on the leg. Once the digits play is completed, the user will receive an '''OnDigitPlayingDone()''' event.
| + | |
| − | | + | |
| − | | + | |
| − | == Leg Creation ==
| + | |
| − | Creating a leg is always done through the definition of a ''call leg attribute''. The values entered in the ''call leg attribute'' will define the type of call leg created and its parameters. The following sections describe several scenarios in which you build a ''call leg''. Instruction will be given on how to fill the leg attributes and how to use them to create the ''call leg''.
| + | |
| − | | + | |
| − | | + | |
| − | === Preparing Leg Attributes ===
| + | |
| − | | + | |
| − | ==== Normal Call Leg Attributes ====
| + | |
| − | For calls including both the signaling and the media path, there is very few parameters that one must enter. The required parameters are:
| + | |
| − | * the called number,
| + | |
| − | * the calling number,
| + | |
| − | * the [[NAP | Network Access Point]].
| + | |
| − | | + | |
| − | Toolpack will automatically select an available channel in the specified NAP to make the call leg. Only NAPs of type ''SS7'', ''ISDN'' or ''SIP'' can be specified for call leg attribute (see [[NAP#NAP Types|NAP Types]]).
| + | |
| − | | + | |
| − | The following code snippet shows how to build the attributes.
| + | |
| − | PTRCTBCMC_CALL_LEG_ATTRIBUTE ptrOutgoingLegAttribute;
| + | |
| − |
| + | |
| − | ptrOutgoingLegAttribute = tbnew CTBCMC_CALL_LEG_ATTRIBUTE();
| + | |
| − |
| + | |
| − | ptrOutgoingLegAttribute->GetCalledNumber() = "123-4567";
| + | |
| − | ptrOutgoingLegAttribute->GetCallingNumber() = "987-6543";
| + | |
| − | ptrOutgoingLegAttribute->GetNetworkAccessPoint() = "NAP_SS7_MONTREAL";
| + | |
| − | | + | |
| − | ==== Media-only Leg Attributes ====
| + | |
| − | For media-only legs, no signaling information is needed but the user can specify which media channel to use and which media profile to use. The only required parameters are the [[NAP | Network Access Point]] and the leg type. Only NAPs of type ''MEDIA TDM'' or ''MEDIA VOIP'' can be specified for media-only leg attribute (see [[NAP#NAP Types|NAP Types]]).
| + | |
| − | | + | |
| − | PTBCMC_MEDIA_DESCRIPTION pMediaDesc;
| + | |
| − | PTRCTBCMC_MEDIA_ONLY_LEG_ATTRIBUTE ptrLegAttribute;
| + | |
| − |
| + | |
| − | ptrLegAttribute = tbnew CTBCMC_MEDIA_ONLY_LEG_ATTRIBUTE();
| + | |
| − | pMediaDesc = ptrLegAttribute->GetProfile().GetMediaDescription();
| + | |
| | | | |
| − | ptrLegAttribute->GetNetworkAccessPoint() = "NAP_MEDIA_1"; | + | [[CAF:_Working_With_Cmc_Call_Legs|Working with CMC Call Legs]] |
| − | pMediaDesc->Type = TBCMC_MEDIA_TYPE_AUDIO;
| + | |
| − | pMediaDesc->Transport = TBCMC_MEDIA_TRANSPORT_TDM or TBCMC_MEDIA_TRANSPORT_IP;
| + | == CAF API layer == |
| | | | |
| − | When only the NAP and type are specified, Toolpack will automatically select an available channel in the specified NAP to allocate the media path. For ''MEDIA TDM'' NAPs, a trunk/timeslot from the specified NAP will be chosen by Toolpack. For ''MEDIA VOIP'' NAPs, an IP interface and port from the specified NAP will be chosen.
| + | A higher-level API uses the base classes ''CTBCMCLeg'' and ''CTBCMCMixer'', but adds the following functionalities: |
| − | | + | - Simplification of call legs creations through single functions (''AddIncoming'', ''AddOutgoing'', ''CreateMixer'') |
| − | If the user wants to specify which media channel to use, it can do so by adding extra information in the leg attribute. For TDM legs, a trunk name and a timeslot number can be specified.
| + | - Centralizing reception of events from call legs and mixers in to a single "Call Flow" (''CTBCAFCallFlow''), which deals with inter-relations between legs and mixers. |
| − | | + | - Auto-destruction of call legs (''CTBCMCLeg'') and mixers (''CTBCMCMixer'') through usage of "smart" pointers. |
| − | PTBCMC_MEDIA_DESCRIPTION pMediaDesc;
| + | - Auto-destruction of the call flow (''CTBCAFCallFlow'') upon destruction of last leg/mixer. |
| − |
| + | |
| − | pMediaDesc->Settings.TdmAudio.Type = TBCMC_MEDIA_SETTINGS_TYPE_TDM_AUDIO;
| + | |
| − | pMediaDesc->Settings.TdmAudio.un8Timeslot = 5;
| + | |
| − | Strncpy
| + | |
| − | (
| + | |
| − | pMediaDesc->Settings.TdmAudio.szTrunkName,
| + | |
| − | "TRUNK_TORONTO_1",
| + | |
| − | sizeof(pMediaDesc->Settings.TdmAudio.szTrunkName)
| + | |
| − | );
| + | |
| − | | + | |
| − | For VOIP legs, the user can control the media by providing local [[SDP]] and peer SDP. Setting the local SDP defines the codec and IP/port used to for the received media stream. Most of the time, the IP address and port should be left empty to let Toolpack choose an available port. Setting the peer SDP defines the codec and IP/port used for the transmitted media stream. Note that Toolpack only allows for the same codec to be used in RX and TX. If both local SDP and peer SDP are specified, codecs that are not in '''both''' SDP will be filtered out.
| + | |
| − | | + | |
| − | For details on how to fill the TBX_SDP_INFO structure needed for SetLocalSDP and SetPeerSDP, see [[CAF:_Filling_SDP_Structures|Filling an SDP Structures]].
| + | |
| − | | + | |
| − | TBX_RESULT Result;
| + | |
| − | TBX_SDP_INFO SdpInfo;
| + | |
| − | PTBCMC_MEDIA_DESCRIPTION pMediaDesc;
| + | |
| − |
| + | |
| − | pMediaDesc = ptrLegAttribute->GetProfile().GetMediaDescription();
| + | |
| − | pMediaDesc->Settings.PacketAudio.Type = TBCMC_MEDIA_SETTINGS_TYPE_PACKET_AUDIO;
| + | |
| − |
| + | |
| − | // Set Local SDP
| + | |
| − | Result = BuildSdpInfo("", 0, SdpInfo); // No IP specified, Toolpack will choose one
| + | |
| − | TBCAF_EXIT_ON_ERROR( Result, "BuildSdpInfo failed." );
| + | |
| − | ptrLegAttribute->GetProfile().SetLocalSDP(SdpInfo);
| + | |
| − |
| + | |
| − | // Set Peer SDP
| + | |
| − | Result = BuildSdpInfo("10.0.0.15", 5000, SdpInfo); // Using peer IP address and port
| + | |
| − | TBCAF_EXIT_ON_ERROR( Result, "BuildSdpInfo failed." );
| + | |
| − | ptrLegAttribute->GetProfile().SetPeerSDP(SdpInfo);
| + | |
| − | | + | |
| − | === Creating the Leg ===
| + | |
| − | Once the leg attributes have been filled, creating the leg in Toolpack is only a matter of creating a CTBCMCLeg object and calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::CreateCall '''CreateCall()'''] on it. No action is taken when an instance of a CTBCMCLeg is created. Call resources are only allocated in the Toolpack system when '''CreateCall()''' is called on the object.
| + | |
| − | | + | |
| − | pCallLeg = new CTBCMCLeg( mun32LegId++, ptrLegAttribute, this, 0, &mLegMutex );
| + | |
| − | pCallLeg->CreateCall();
| + | |
| − | | + | |
| − | For legs with signaling, the '''CreateCall()''' will trigger the sending of the call setup message (SIP Invite, SS7 IAM, etc.). In that case, the media resources are not allocated immediately. They will be allocated only when the signaling part of the call setup is complete. If the application requests a media action (PlayFile, StartDigitCollection, etc.) on the leg, this will immediately trigger the allocation of the media resources even if the call is not yet answered (used for early media for example).
| + | |
| − | | + | |
| − | [[Image:CallFlow SignalingMediaLeg Creation.JPG|thumb|center|350px|Call flow for creation of leg with signaling]]
| + | |
| − | | + | |
| − | | + | |
| − | For media-only legs, the media ressources will always be allocated as soon as '''CreateCall()''' is called.
| + | |
| − | | + | |
| − | [[Image:CallFlow MediaOnlyLeg Creation.JPG|thumb|center|350px|Call flow for media-only leg creation]]
| + | |
| − | | + | |
| − | | + | |
| − | Once a call is fully active (call answered and media allocated), event [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnProfileChanged '''OnProfileChanged()'''] will be sent on the leg. In the cases where the user had not specified the IP/port to use, once this event is received, the media profile has been updated with the values chosen by Toolpack and the updated values can be retrieved using the functions '''GetLocalSDP()''' and '''GetPeerSDP()''' of the profile.
| + | |
| − | Note that the '''OnProfileChanged()''' event is also sent after the media profile has been modified with the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::ChangeProfile '''ChangeProfile()'''] function (see [[#Modifying Media Profile|Modifying Media Profile]]) and when a connected peer has requested it (through a SIP re-INVITE for example).
| + | |
| − | | + | |
| − | | + | |
| − | See [[CAF:_Leg_Creation_Samples|Leg creation example]] for sample code of leg creation in different scenarios.
| + | |
| − | | + | |
| − | === Caveats ===
| + | |
| − | * The call leg attribute is an object containing the call leg information (called/calling numbers, media profile, etc) that needs to be allocated by the caller and used when creating the leg object. It will be freed automatically when the leg is destroyed (it uses a shared-pointer so it is in fact destroyed when there are no more reference to it).
| + | |
| − | | + | |
| − | | + | |
| − | == Interaction with Legs ==
| + | |
| − | | + | |
| − | === Playing and Collecting Digits ===
| + | |
| − | You can add tones you want to play by using [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___e_v_e_n_t___a_t_t_r_i_b_u_t_e.html#CTBCMC_EVENT_ATTRIBUTE::AddToneString '''AddToneString()'''] available in [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___e_v_e_n_t___a_t_t_r_i_b_u_t_e.html CTBCMC_EVENT_ATTRIBUTE] class.
| + | |
| − | You can then play digits defined by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::PlayDigit '''PlayDigit()'''] on a leg. Toolpack will receive the request and play the digits. Once digits are played, the leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnDigitPlayingDone '''OnDigitPlayingDone()'''] event.
| + | |
| − | | + | |
| − | You can also configure a leg to collect digits played. To start the digit collection, you have to call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::StartDigitCollection '''StartDigitCollection()'''] on the leg. Note that you will have to specify which digits you want to collect before starting the digit collection by calling '''AddToneString()''' on a CTBCMC_EVENT_ATTRIBUTE object. To stop the digit collection, you have to call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::StopDigitCollection '''StopDigitCollection()''']. A leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnDigitCollected '''OnDigitCollected()'''] event on each digit received that correspond to a tone string specified with the previously call to '''AddToneString()'''.
| + | |
| − | | + | |
| − | === Playing and Collecting Tones ===
| + | |
| − | You can add tones you want to play by using [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___e_v_e_n_t___a_t_t_r_i_b_u_t_e.html#CTBCMC_EVENT_ATTRIBUTE::AddToneString '''AddToneString()'''] available in [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___e_v_e_n_t___a_t_t_r_i_b_u_t_e.html CTBCMC_EVENT_ATTRIBUTE] class.
| + | |
| − | You can then play events by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::PlayEvent '''PlayEvent()'''] on a leg. Toolpack will receive the request and play the events. Once events are played, the leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnEventPlayingDone '''OnEventPlayingDone()'''] event. Note that you can cancel an event to be played by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::CancelEvent '''CancelEvent()'''] on the leg after a '''PlayEvent()''' has been called.
| + | |
| − | | + | |
| − | | + | |
| − | Two kinds of string can be passed to '''AddToneString()''' to play a tone. The first type is to play well known tones such as dtmf and fax tone. The syntax is really simple and is based on H248 package and signal ids. The first component of the string is the package id and the second is the signal id, both formated in string. So, to play dtmf 0, you have to format the following string: "dg/d0", where "dg" is for package "dtmf generation" and "d0" is for "dtmf 0".
| + | |
| − | | + | |
| − | | + | |
| − | The second type of string is to play custom tone. The syntax is much more complicated than the first one, but it follows a well described syntax which can be found in [http://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-H.248.6-200011-I!!PDF-E&type=items/.pdf '''H248.6 Dynamic Tone Definition Package''']. This kind of string allows you to specify frequencies, duration, amplitude and repeating count of the tone. You can also specify well known tones and change their default duration, amplitude and repeating count. It is possible to describe a sequence of tones or frequencies that are played in one segment. Here are some examples of the syntax:
| + | |
| − | | + | |
| − | *;Frequencies 400Hz and 600Hz mixed together for 200ms, amplitude at -10dB and repeating 3 times (playing 4 times):
| + | |
| − | :*(((#400)+(#600)),200,-10)*3
| + | |
| − | :
| + | |
| − | *;Dtmf 5 repeated infinitly:
| + | |
| − | :*((0x0005,0x0015))*0
| + | |
| − | :
| + | |
| − | *;Multifrequency tone 8:
| + | |
| − | :*((mfg,mf8))
| + | |
| − | :
| + | |
| − | *;Frequency 440Hz played for 300ms at -10dB followed by frequency 600Hz played for 200ms at -5dB and then followed by dtmf 2, all this repeated infinitly:
| + | |
| − | :*((#440,300,-10),(#600,200,-5),(0x0005,0x0012))*0
| + | |
| − | :
| + | |
| − | | + | |
| − | | + | |
| − | You can also configure a leg to collect events played. To start the event collection, you have to call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::StartEventCollection '''StartEventCollection()'''] on the leg. Note that you will have to specify which events you want to collect before starting the event collection by calling '''AddToneString()''' on a CTBCMC_EVENT_ATTRIBUTE object. To stop the event collection, you have to call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::StopEventCollection '''StopEventCollection()''']. A leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnEventCollected '''OnEventCollected()'''] event on each event received that correspond to a tone string specified when calling '''StartEventCollection()'''.
| + | |
| − | | + | |
| − | | + | |
| − | Only one type of string is accepted to specify which events to collect. The string is the same as the first type to play event. Signal ids that are also event id are accepted. This means that you can ask to collect "dg/d0" (dtmf generation/dtmf 0) and the detection will be done anyway. But, when the event is detected, it's the event id that will be returned, which means that "dd/d0" (dtmf detection/dtmf 0) will be returned instead of "dg/d0". You can also detect all events from a package by putting a * as event id, so "dd/*" will detect all dtmf tones.
| + | |
| − | | + | |
| − | | + | |
| − | The most commonly used package are 5 and 6 [http://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-H.248.1-200509-I!!PDF-E&type=items/.pdf '''(H248.1 Annex E)''']: dtmf generation and dtmf detection. As H248 does not define events and signals for fax tone, we added a special package to do so. Package tbfax (0x0251) contains three events and two signals: cng (0x0080), g164 (0x0081) and only for detection g165 (0x0082).
| + | |
| − | | + | |
| − | | + | |
| − | | + | |
| − | <code>test test</code>
| + | |
| − | | + | |
| − | === Collecting digits and tones while call legs are joined ===
| + | |
| − | By default, when two call legs are joined together through function CTBCMCCallLeg::Join(), tone collection is automatically disabled.
| + | |
| − | One of the arguments of the Join() function ("in_fDisableToneWhileJoined") will allow to control if automatic tone collection feature is used or not on a call.
| + | |
| − | | + | |
| − | Why is Toolpack disabling tone collection on joined legs by default?
| + | |
| − | That's because tone collection introduces a 40ms delay in the audio connection (required to provide tone suppression), and most of the time it is no more require to collect digits while two call legs are joined, so it would be useless to leave 40ms delay while tone collection is no more required.
| + | |
| − | | + | |
| − | === Playing and Recording Audio Files ===
| + | |
| − | You can play an audio stream on a leg by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::PlayStream '''PlayStream()'''] on it. To specify which audio stream you want to play, you have to specify it by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___p_l_a_y___a_t_t_r_i_b_u_t_e.html#CTBCMC_PLAY_ATTRIBUTE::AddPlayFilePath '''AddPlayFilePath()'''] available in [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___p_l_a_y___a_t_t_r_i_b_u_t_e.html CTBCMC_PLAY_ATTRIBUTE] class. Toolpack will receive the request and play the stream. Once it is played, the leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnStreamPlayingDone '''OnStreamPlayingDone()'''] event.
| + | |
| − | | + | |
| − | You can also configure a leg to record an audio stream. First you must specify file paths to record by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___r_e_c_o_r_d___a_t_t_r_i_b_u_t_e.html#CTBCMC_RECORD_ATTRIBUTE::AddRecFilePath '''AddRecFilePath()'''] available in [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c___r_e_c_o_r_d___a_t_t_r_i_b_u_t_e.html CTBCMC_RECORD_ATTRIBUTE] class. The you can call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::RecordStream '''RecordStream()'''] on a leg. Once the stream is recorded, the leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnStreamRecordingDone '''OnStreamRecordingDone()'''] event.
| + | |
| − | | + | |
| − | You can pause an active playing or recording stream by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::PauseStream '''PauseStream()'''] and you can resume it by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::ResumeStream '''ResumeStream()''']. If you want to stop an active playing or recording stream, you have to call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::StopStream '''StopStream()'''] on the leg.
| + | |
| − | | + | |
| − | === Modifying Media Profile ===
| + | |
| − | It is always possible to modify the media profile of a leg after it was created. This can be used for example to change to a more compressed codec if bandwidth resources become sparse or to switch to T.38 Fax after a fax tone was detected.
| + | |
| − | | + | |
| − | The media profile is stored in the leg attributes and can be modified like this :
| + | |
| − | TBX_SDP_INFO SdpInfo;
| + | |
| − | PCTBCMC_MEDIA_ONLY_LEG_ATTRIBUTE pMediaLegAttribute;
| + | |
| | | | |
| − | pMediaLegAttribute = pCallLeg->GetAttributes().GetMediaOnlyLegAttribute();
| + | The following page explains how to work with CAF Call leg framework (CTBCAFCallLeg, CTBCAFCallFlow, CTBCAFCallBehavior, etc...) |
| − | pMediaLegAttribute->GetProfile().GetLocalSDP(SdpInfo);
| + | |
| − | Strncpy
| + | |
| − | (
| + | |
| − | SdpInfo.aConnections[0].szIp,
| + | |
| − | "",
| + | |
| − | sizeof( SdpInfo.aConnections[0].szIp )
| + | |
| − | );
| + | |
| − | SdpInfo.Capabilities.aCapGroups[0].aSimultaneousCap[0].un16UdpPort = 0;
| + | |
| − | pMediaLegAttribute->GetProfile().SetLocalSDP(SdpInfo);
| + | |
| | | | |
| − | pCallLeg->ChangeProfile();
| + | [[CAF:_Working_With_Caf_Call_Legs|Working with CAF Call Legs and behaviors]] |
| − | | + | |
| − | Once the attributes have been modified, '''ChangeProfile()''' must be called to activate the new profile. In the case of media-only legs, activating a modified profile will immediately reallocate the media resources. In the case of a SIP call leg, activating the new profile will trigger a new negotiation with the peer (INVITE-RESPONSE) after which the media resources will be allocated using the newly negotiated codecs.
| + | |
| − | | + | |
| − | Once the profile change has completed (or failed), event '''OnProfileChanged()''' will be received on the leg.
| + | |
| − | | + | |
| − | For SIP call leg, if the peer entity sends us re-INVITE with a new SDP during a call, the media resource will be automatically updated and event '''OnProfileChanged()''' will be received on the leg.
| + | |
| − | | + | |
| − | === Controlling the Signaling ===
| + | |
| − | When a call leg receives the '''OnCallLegPresent()''' event, it indicates an incoming call. To confirm that the call contains sufficient valid information to process the call on the system, you have to call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::AcceptCall '''AcceptCall()'''] on the leg. If a call leg receives the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnCallAccepted '''OnCallAccepted()'''] event, it means that an outgoing call has been accepted by the remote peer. This event usually means that the calling number has been accepted and that the call is currently being processed.
| + | |
| − | | + | |
| − | After an incoming call has been accepted, a call leg can notify the remote peer that the incoming call has been put in the "ringing" state by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::AlertCall '''AlertCall()''']. In the same way, a call leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnCallAlerting '''OnCallAlerting()'''] event when an outgoing call has been put in the "ringing" state by the remote peer.
| + | |
| − | | + | |
| − | When an incoming call is answered, a call leg can notify the remote peer of the incoming call answered by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::AnswerCall '''AnswerCall()''']. In the same way, a call leg will receive [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnCallAnswered '''OnCallAnswered()'''] event when an outgoing call has been answered by the remote peer.
| + | |
| − | | + | |
| − | SendCallSuppInfo/OnCallSuppInfo
| + | |
| − | | + | |
| − | == Leg Termination ==
| + | |
| − | | + | |
| − | Terminating a call leg is a 2 steps process:
| + | |
| − | # Call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::TerminateCall '''TerminateCall()''']
| + | |
| − | # Free leg object on [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnCallTerminated '''OnCallTerminated()''']
| + | |
| − | | + | |
| − | When '''TerminateCall()''' is called, the Toolpack framework will start leg termination. This includes media resources freeing and, for leg with signaling, sending of the appropriate signaling message to terminate the call. Once the media resources have been deallocated and call termination signaling is done, Toolpack will call '''OnCallTerminated()''' on the leg. When this event is received on the leg, this leg no more exists in Toolpack and the object can thus be freed. At the end of the '''OnCallTerminated()''' handler, the default implementation of class CTBCMCLeg will call method [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::Free '''Free()'''] on the leg's [https://docs.telcobridges.com/mediawiki/autodoc/class_i_t_b_c_m_c_free_listener.html ITBCMCFreeListener] interface. The ITBCMCFreeListener to use can be specified either in the CTBCMCLeg constructor and by calling [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::SetFreeListener '''SetFreeListener()'''] on the leg. The leg can be it's own ''FreeListener'', in which it just 'delete' itself when its '''Free()''' method is called. An application specific ''FreeListener'' can be used for cases where other action needs to be taken before the leg is deleted. An example could be the case where the leg object was allocated from a pool and it should be returned to that pool instead of being deleted.
| + | |
| − | | + | |
| − | [[Image:TerminateCall from application.jpg|thumb|center|350px|Call flow for leg termination initiated by user application]]
| + | |
| − | | + | |
| − | | + | |
| − | In some situation, it is possible that leg termination be initiated by Toolpack. This can happen for leg with signaling, when a call termination request is received on the signaling channel. It can also happen on any type of leg in the event of sudden media resource unavailability and other media resource or signaling error. In these cases, the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnCallTerminatingIndication '''OnCallTerminatingIndication()'''] is sent to the leg. On reception of this event, the application should initiate call termination as shown below.
| + | |
| − | | + | |
| − | [[Image:TerminateCall from Toolpack.jpg|thumb|center|350px|Call flow for leg termination initiated by Toolpack]]
| + | |
| − | | + | |
| − | | + | |
| − | In case of internal system error or major communication lost with the Toolpack engine, Toolpack would send the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnLegTerminated '''OnLegTerminated()'''] event. This event indicates that the leg does not exist anymore on the Toolpack side and the user should free its object without trying any other interaction with Toolpack through it.
| + | |
| − | | + | |
| − | == Leg Synchronization on Failover ==
| + | |
| − | When a Toolpack application is restarted or when a standby application is activated, it goes through a synchronization phase with the Toolpack framework. During this phase, Toolpack informs the application of all the already allocated call legs through the '''OnCallLegSync()''' event of the [https://docs.telcobridges.com/mediawiki/autodoc/class_i_t_b_c_m_c_lib_user.html ITBCMCLibUser] interface (this interface must be implemented by all user applications). One event will be received for each leg being synchronized. The course of action to take when receiving a leg synchronization event depends on the ability of the application to resynchronize its states with theses legs.
| + | |
| − | | + | |
| − | * If the application can't resynchronize active legs or if it does not want to resychronize the leg for which it is receiving an '''OnCallLegSync()''' event, it must refuse the leg by calling the static function [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::RefuseLeg '''RefuseLeg()'''].
| + | |
| − | *If the application wants the resynchronize the leg or if it does not yet have enough information to decide, it must create a CTBCMCLeg object using the leg attributes received in the event.
| + | |
| − | | + | |
| − | Once all '''OnCallLegSync()''' have been sent, Toolpack will start synchronization of the links between legs through '''OnLinkSync()'''. This event indicates that two legs are connected together. It can be used by the application to rebuild its internal states. As for the legs, unwanted links can be refused by calling the static function [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::RefuseLink '''RefuseLink()'''].
| + | |
| − | | + | |
| − | When all links have been synchronized, Toolpack sends the '''OnCmcLibReady()''' event indicating that active resources synchronization is complete. At that moment, the application has all the information available on the Toolpack side to determine if the legs should be kept or release. Any leg that the application does not want to keep can be refused by calling '''RefuseLeg()''' on it. For all legs that have not been refused, an event [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::OnSyncDone '''OnSyncDone()'''] will be sent on the leg. Once this event has been received on a leg, the leg is fully functional and the application can start calling any usual Toolpack function on it.
| + | |
| − | | + | |
| − | [[Image:CallFlow Sync After Application Restart.jpg|thumb|center|350px|Call flow for leg synchronization]]
| + | |
| − | | + | |
| − | | + | |
| − | ===Loss of Communication with Toolpack Engine===
| + | |
| − | If communication is lost with the Toolpack Engine, event '''OnCmcLibNotReady()''' will be sent to the application. It indicates that the Toolpack framework is no more accessible. The legs are still valid at that time but no action can be executed on them as long the CmcLib is not ready. If the connection with the Toolpack Engine is not back up in less than 10 seconds, the CmcLib will declare a major communication loss and will call '''OnLegTerminated()''' on all the legs. In that case, when communication is regained with the Toolpack Engine, the synchronization sequence will start again from the beginning.
| + | |
| − | | + | |
| − | [[Image:CallFlow Sync After Comm Restart Passed 10sec.jpg|thumb|center|350px|Call flow for leg synchronization after a communication restart passed 10 seconds.]]
| + | |
| − | | + | |
| − | | + | |
| − | If the communication is regained before the 10 seconds timeout, event '''OnCmcLibReady()''' will be sent and the application can then continue working normally with its existing call legs. Note that you can also receive '''OnLegTerminated()''' on some legs before receiving the '''OnCmcLibReady()''' if those legs were in a transient state when disconnection occurred.
| + | |
| − | | + | |
| − | [[Image:CallFlow Sync After Comm Restart Within 10sec.jpg|thumb|center|350px|Call flow for leg synchronization after a communication restart within 10 seconds.]]
| + | |
| − | | + | |
| − | == Bridging the Media Path ==
| + | |
| − | === Join ===
| + | |
| − | | + | |
| − | To bridge the media path between two legs, one must call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::Join '''Join()'''] on one of the leg, giving the second leg as a parameter. This will connect the media path between the two legs according to the link properties set on the leg on which '''Join()''' is called. These link properties can be modified by overloading the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::GetJoinAttributes '''GetJoinAttributes()''']. The important attribute to set is '''IsFullDuplex()''' that indicates if the connection will be made full-duplex (A<-->B) or half-duplex (A-->B). Prior to release 2.5.2, the default connection mode is half-duplex. For all release version 2.5.2 or higher, the default connection mode is full-duplex.
| + | |
| − | | + | |
| − | '''Warning:''' If two legs are already connected in half-duplex and you want to connect them in full-duplex, you must first Unjoin() the legs, then Join() them in full-duplex. You can '''NOT''' only do another half-duplex in the opposite direction.
| + | |
| − | | + | |
| − | | + | |
| − | When legs are joined, it creates a link identified with a unique ''link id''. It is the responsibility of the application to provide this unique ''link id'' by implementing the [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::GetLinkId '''GetLinkId()'''] function of the leg. It is planned to allow the user to provide a value of '0' to let the Toolpack system automatically choose a ''link id'', but as of this writing this feature is not yet available.
| + | |
| − | | + | |
| − | '''Warning:''' When two legs are joined, the application must ensure that '''GetLinkId()''' on both leg will return the right ''link id''. This will ensure that when the link needs to be removed, both A->Unjoin() and B->Unjoin() will work correctly.
| + | |
| − | | + | |
| − | ==== Setting the link properties ====
| + | |
| − | | + | |
| − | In your leg class, add a member variable to store the join attributes for that leg.
| + | |
| − | | + | |
| − | CTBCMC_JOIN_ATTRIBUTE mJoinAttribute;
| + | |
| − | | + | |
| − | Then set the join properties you want in your leg class constructor (or at any other location that will run '''before''' the '''Join()''' is done:
| + | |
| − | | + | |
| − | mJoinAttribute.IsFullDuplex() = TBX_TRUE;
| + | |
| − | | + | |
| − | Last, implement the '''GetJoinAttributes()''' function.
| + | |
| − | | + | |
| − | CTBCMC_JOIN_ATTRIBUTE & CH248Termination::GetJoinAttributes()
| + | |
| − | {
| + | |
| − | return mJoinAttribute;
| + | |
| − | }
| + | |
| − | | + | |
| − | ==== Broadcasting a media source ====
| + | |
| − | At the time of writing this, broadcast of a single media source to multiple destinations is not yet possible.
| + | |
| | | | |
| − | === Unjoin ===
| + | The following page provides more details on call legs re-synchronization between toolpack_engine application and user "CAF" application: |
| − | To disconnect the media path between two legs, one must call [https://docs.telcobridges.com/mediawiki/autodoc/class_c_t_b_c_m_c_leg.html#CTBCMCLeg::Unjoin'''Unjoin()'''] on any of the legs. The '''GetLinkId()''' function of the leg on which '''Unjoin()''' is called must return the ''link id'' that was used when the legs were joined.
| + | |
| | | | |
| − | [[category:CAF]] | + | [[CAF:_Call_Legs_Resync|Re-synchronizing CAF call legs]] |
| − | [[category:Needs revising]]
| + | |
TelcoBridges Toolpack framework offers two API layers to manipulate call legs and audio mixers (conferences).
We recommend that developers use the CAF API layer, as it offers higher-level functionality which accelerate application development.
The following page explains how to work with CTBCMCLeg directly, for lower-level applications that don't want the convenience of the CAF Call framework
The following page explains how to work with CAF Call leg framework (CTBCAFCallLeg, CTBCAFCallFlow, CTBCAFCallBehavior, etc...)
The following page provides more details on call legs re-synchronization between toolpack_engine application and user "CAF" application:
