Toolpack:Creating an MTP3 Route A
From TBwiki
(Difference between revisions)
(Created page with 'MTP3 routes are built to route traffic from previously created point codes using linksets. One route is created per prevously defined point codes. To create an MTP3 route: …') |
(add text regarding the number of routes required) |
||
| (8 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[MTP3]] routes are built to route traffic from previously created point codes using linksets. | + | === '''''Applies to version(s): v2.5, v2.6., 2.7''''' === |
| + | {{DISPLAYTITLE:Creating an MTP3 Route}} | ||
| + | [[MTP3 Layer|MTP3]] routes are built to route traffic from previously created point codes using linksets. | ||
| + | |||
| + | You require 1 route per point codes in your system. This means 1 route per DPC (SSP and STP) and 1 per source point code (OPC). | ||
To create an MTP3 route: | To create an MTP3 route: | ||
| + | |||
1- Click '''Create New Mtp3 Route''' in the MTP3 network configuration window: | 1- Click '''Create New Mtp3 Route''' in the MTP3 network configuration window: | ||
| Line 13: | Line 18: | ||
* Select a '''restart procedure''' | * Select a '''restart procedure''' | ||
* Select a '''point type''' | * Select a '''point type''' | ||
| − | * Check the '''Route to Adjacent''' box, if this route is directed an | + | * Check the '''Route to Adjacent''' box, if this route is directed to an adjacent network |
* Click '''Create''' | * Click '''Create''' | ||
[[Image:Toolpack_v2.5_Creating_MTP3_Route.png]] | [[Image:Toolpack_v2.5_Creating_MTP3_Route.png]] | ||
| − | 3- Verify that the '''Mtp3Route was successfully created''' message appears | + | 3- Verify that the '''"Mtp3Route was successfully created"''' message appears |
[[Image:Toolpack_v2.5_MTP3_Route_Created.png]] | [[Image:Toolpack_v2.5_MTP3_Route_Created.png]] | ||
| Line 28: | Line 33: | ||
[[Image:Toolpack_v2.5_MTP3_Route_Linkset.png]] | [[Image:Toolpack_v2.5_MTP3_Route_Linkset.png]] | ||
| + | |||
| + | |||
| + | ==List of Parameters== | ||
| + | |||
| + | * [[Parameter: Name|Name]] | ||
| + | * [[Parameter: Point Code|Point Code]] | ||
| + | * [[Parameter: Restart Procedure|Restart Procedure]] | ||
| + | * [[Parameter: Signaling Point Type|Point Type]] | ||
| + | * [[Parameter: Route to Adjacent|Route to Adjacent]] | ||
Latest revision as of 13:47, 12 February 2014
Applies to version(s): v2.5, v2.6., 2.7
MTP3 routes are built to route traffic from previously created point codes using linksets.
You require 1 route per point codes in your system. This means 1 route per DPC (SSP and STP) and 1 per source point code (OPC).
To create an MTP3 route:
1- Click Create New Mtp3 Route in the MTP3 network configuration window:
2- Configure the new MTP3 route:
- Enter a name for the route
- Select a point code for the route
- Select a restart procedure
- Select a point type
- Check the Route to Adjacent box, if this route is directed to an adjacent network
- Click Create
3- Verify that the "Mtp3Route was successfully created" message appears
4- Associate the newly created route with a linkset:
- Select a linkset from the list provided at the bottom of the route configuration window
- Click the "<<" button to associate the linkset with the newly created route
