From TBwiki
(Difference between revisions)
|
|
| Line 114: |
Line 114: |
| | *[[Configure SIP]] | | *[[Configure SIP]] |
| | | | | | |
| − | *[[Configure SIGTRAN]] | + | *[[Toolpack:Protocol_Stack_Settings_A#SS7_ISUP|Configure SIGTRAN]] |
| | | | | | |
| | *[[Configure H.248]] | | *[[Configure H.248]] |
| Line 151: |
Line 151: |
| | *[[Configure SIP]] | | *[[Configure SIP]] |
| | | | | | |
| − | *[[Configure SIGTRAN]] | + | *[[Toolpack:Protocol_Stack_Settings_A#SS7_ISUP|Configure SIGTRAN]] |
| | | | | | |
| | *[[Configure H.248]] | | *[[Configure H.248]] |
Revision as of 14:28, 27 April 2015
Applies to version(s): v2.8.
This article provides the steps required to complete the most common IP network configurations using the Web Portal.
One subnet, Two IP Addresses, Untagged
| Configure IP Network A
|
Configure IP Network B
|
- Subnet A is access through MGMT0
- MGMT0 network interface modification requires the use of the tbchangeip shell script
- Use tbchangeip with the following parameters:
- IP Address: 192.168.4.10
- Netmask: 255.255.255.0
- Default gateway: 192.168.4.1
|
Subnet B is untagged and bonded over VOIP0 and VOIP1 ports.
- Delete voip0 and voip1 virtual port
- Create VP_VOIP virtual port:
- Name: VP_VOIP
- vLanId: Untagged
- Physical Ports: voip0, voip1
- Delete voip0 and voip1 IP Address
- Create VOIP_ADDRESS IP Address:
- Name: VOIP_ADDRESS
- Virtual Ports: VP_VOIP
- IP Address: 192.168.4.20
- Netmask: 255.255.255.0
- Services: RTP, SIP, SIGTRAN
|
| Configure SIP
|
Configure SIGTRAN
|
Configure H.248
|
Configure RADIUS
|
- Configure SIP
- IP range parameters:
- Name: PORT_RANGE_VOIP
- IP Interface: VOIP_ADDRESS
- Minimum Port: 20000
- Maximum Port: 30000
- SIP transport server parameters:
- Port: 5060
- IP Interface: VOIP_ADDRESS
- SIP NAP parameters:
- Proxy Address: 192.168.4.110
- Port Range: PORT_RANGE_VOIP
|
|
- When you Configure H.248, set the following:
- Local IP Address and Public IP Address: 192.168.4.210
[Public IP or NAT public IP]
|
- When you Configure RADIUS, set the following:
- Source IP interface: Any
- Radius -> Radius Server
- Public IP Address: Empty
|
|
Two subnets, One IP per subnet, untagged
| Configure IP Network A
|
Configure IP Network B
|
- Subnet A is access through MGMT0
- MGMT0 network interface modification requires the use of the tbchangeip shell script
- Use tbchangeip with the following parameters:
- IP Address: x.x.x.x
- Netmask: 255.255.255.0
- Default gateway: x.x.x.x
|
Subnet B is untagged and is bonded over VOIP0 and VOIP1 ports.
|
| Configure SIP
|
Configure SIGTRAN
|
Configure H.248
|
Configure RADIUS
|
|
|
|
|
|
|
Two VLAN, Three IP Address, tagged
| Configure IP Network A
|
Configure IP Network B
|
|
|
Subnet B uses untag bonded over VOIP0 and VOIP1 ports
|
| Configure SIP
|
Configure SIGTRAN
|
Configure H.248
|
Configure RADIUS
|
|
|
|
|
|
|
