Toolpack:Create a SCCP userpart
From TBwiki
(Difference between revisions)
(initial content) |
m |
||
| Line 1: | Line 1: | ||
This step is used to initialize the userpart parameters of the SCCP layer | This step is used to initialize the userpart parameters of the SCCP layer | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Description of parameters == | == Description of parameters == | ||
General explanation of the configuration parameters: | General explanation of the configuration parameters: | ||
| − | |||
*The '''Handle SCCP network''' parameter specifies the handle of the SCCP network | *The '''Handle SCCP network''' parameter specifies the handle of the SCCP network | ||
| Line 53: | Line 46: | ||
| Host TCAP|| SCCP userpart is used as a standalone and communicates with remote TCAP layer (host application) | | Host TCAP|| SCCP userpart is used as a standalone and communicates with remote TCAP layer (host application) | ||
|} | |} | ||
| − | |||
---- | ---- | ||
| − | |||
*The '''Subsystem number''' parameter specifies a subsystem number for this userpart. Allowable values are from 1 to 255. See the table for ' | *The '''Subsystem number''' parameter specifies a subsystem number for this userpart. Allowable values are from 1 to 255. See the table for ' | ||
| Line 63: | Line 54: | ||
*The '''Array of backup point code entries''' parameter specifies the list of backup point code for this Userpart. This parameter is reconfigurable. | *The '''Array of backup point code entries''' parameter specifies the list of backup point code for this Userpart. This parameter is reconfigurable. | ||
*The '''Array of priority of backup point code entries''' parameter specifies the list of priority of each backup point code for this Userpart. Allowable values are from 0 to 255. | *The '''Array of priority of backup point code entries''' parameter specifies the list of priority of each backup point code for this Userpart. Allowable values are from 0 to 255. | ||
| − | |||
'''Note:''' Zero being the lowest priority. | '''Note:''' Zero being the lowest priority. | ||
| − | |||
---- | ---- | ||
| − | |||
*The number concerned point code parameter specifies the number of concerned point code entries in the 'Concerned Point Code Entries' array | *The number concerned point code parameter specifies the number of concerned point code entries in the 'Concerned Point Code Entries' array | ||
*The array of concerned point code entries parameter (specifies the list of concerned point code for this Userpart | *The array of concerned point code entries parameter (specifies the list of concerned point code for this Userpart | ||
| − | |||
| − | |||
| − | |||
Latest revision as of 12:14, 1 May 2018
This step is used to initialize the userpart parameters of the SCCP layer
Description of parameters
General explanation of the configuration parameters:
- The Handle SCCP network parameter specifies the handle of the SCCP network
- The Unique identifier SCCP Userpart parameter specifies the unique ID of the SCCP Userpart for a SS7 system
- The Message priority parameter specifies the priority of messages. Allowable values are as follows:
| SCCP Message Priority | Description |
|---|---|
| Highest | |
| 0 | Same as highest |
| 1 | |
| 2 | |
| 3 | Same as lowest |
| Lowest |
- The Connection mode parameter specifies the different modes of connection for a SCCP userpart. Allowable values include:
| SCCP connection mode | Description |
|---|---|
| TCAP | SCCP userpart is used in conjunction with an above local TCAP layer and cannot be controlled by the host application but the host application will receive ALARM notifications |
| Host TCAP | SCCP userpart is used as a standalone and communicates with remote TCAP layer (host application) |
- The Subsystem number parameter specifies a subsystem number for this userpart. Allowable values are from 1 to 255. See the table for '
SCCP SSN value to identify SCCP user' in Toolpack:Create a SCCP route.
- The Number backup point code parameter specifies the number of backup point code entries in the Backup Point Code Entries and the Priority Backup Point Code Entries arrays.
- The Array of backup point code entries parameter specifies the list of backup point code for this Userpart. This parameter is reconfigurable.
- The Array of priority of backup point code entries parameter specifies the list of priority of each backup point code for this Userpart. Allowable values are from 0 to 255.
Note: Zero being the lowest priority.
- The number concerned point code parameter specifies the number of concerned point code entries in the 'Concerned Point Code Entries' array
- The array of concerned point code entries parameter (specifies the list of concerned point code for this Userpart
