Toolpack Application:tbstatus

From TBwiki
Jump to: navigation, search

Role

tbstatus is used to access/set status of the system. It requires a path for you to query.


Usage

  • To get all status information from the system:
tbstatus -gw SystemId
tbstatus -gw 12358


  • General get query:
tbstatus -gw SystemId /[StatusPath]
  • Example: Get all naps status:
tbstatus -gw 12358 /nap
  • Example: To get a SS7 interface circuit group status information:
tbstatus isup:ISUP/interface:[ISUP Interface name]/cic_group:[Circuit Group Name]
tbstatus isup:ISUP/interface:ISUP_IF_6009/cic_group:CG_E1_8

Output:

0:/isup:ISUP/interface:ISUP_IF_6009/cic_group:CG_E1_8
CG_E1_8 -
  - desired_group_state                   : Default       (Default,Blocked,Unblocked)
  - toggle_group_reset                    : No            (No,Yes)
  - start_continuity_check                : No            (No,Yes)
  - interface_down                        true
  - idle_cnt                              0
  - incoming_cnt                          0
  - outgoing_cnt                          0
  - locally_blocked_cnt                   0
  - remotely_blocked_cnt                  0
  - locally_remotely_blocked_cnt          0
  - reset_cnt                             0
  - total_ccr_success_cnt                 0
  - total_ccr_fail_cnt                    0
  - last_ccr_unknown_cnt                  0
  - last_ccr_in_progress_cnt              0
  - last_ccr_success_cnt                  0
  - last_ccr_fail_cnt                     0
  - last_ccr_error_cnt                    0

Note: Settable parameters are shown in purple when doing a get query


  • General set query (Settable parameters are shown in purple when doing a get query):
tbstatus -gw SystemId /[StatusPath]::[ParameterToSet]=[NewParameterValue]
  • Example: To set the loopback state of a E1 line service to NONE (Meaning enable). NOTE: The path would be different for DS3 or STM1:
tbstatus -gw SystemId /adapter:[TmediaSerialNumber]/line_interface:[LineInterfaceName]/line_service:[LineServiceName]::loopback=NONE
tbstatus -gw 12358 /adapter:TB001234/line_interface:LI_TB001234_00/line_service:LS_TB001234_00::loopback=NONE
  • Example: To block a SS7 interface circuit group:
tbstatus isup:ISUP/interface:[ISUP Interface name]/cic_group:[Circuit Group Name]::desired_group_state=[state name]
state name can be: Default, Blocked, Unblocked (unblocked should not be used in normal circumstances)
tbstatus isup:ISUP/interface:ISUP_IF_6009/cic_group:CG_E1_8::desired_group_state=Default
tbstatus isup:ISUP/interface:ISUP_IF_6009/cic_group:CG_E1_8::desired_group_state=Blocked
  • Example: To change the state of a M3UA Peer Server Process (Default,Asp-up,Asp-down,Abort,Shutdown,Inhibit,Uninhibit):
Note: Two commands must be done at the same time and an additional "::" must be used
./tbstatus /m3ua/psp:M3UA_SGP1::select_sap_for_set_state=M3UA_SAP::set_desired_asp_state=Asp-down

Note: in release 2.7, you can add a "-0" to get level 0 information.

Use tbstatus in script

See Tbstatus Monitoring.

Personal tools