Toolpack:Protocol Stack Settings A

From TBwiki
(Difference between revisions)
Jump to: navigation, search
m (M2PA-MTP3-ISUP)
(M3UA-ISUP)
Line 263: Line 263:
  
 
| valign="top" |  
 
| valign="top" |  
*[[Toolpack:Creating the SCTP Configuration C|Edit the SCTP Configuration]]  
+
*[[Toolpack:Creating the SCTP Configuration C|Create the SCTP Configuration]]  
 
*[[Toolpack:Creating SS7 Point Codes C|Create SS7 Point Codes]]  
 
*[[Toolpack:Creating SS7 Point Codes C|Create SS7 Point Codes]]  
 
*[[Toolpack:Creating an M3UA Configuration (IPSP) C|Create an M3UA Configuration]]  
 
*[[Toolpack:Creating an M3UA Configuration (IPSP) C|Create an M3UA Configuration]]  

Revision as of 09:12, 18 September 2014


Contents

Protocol Stacks

ISDN NFAS

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configure ISDN-PRI Signaling
(Step 3)
Modify NAP profile
(Step 4)
Configure Network Access Points (NAPs)

OR

ISDN Advanced Features

ISDN Overlap Sending



CAS

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configuring a CAS stack
(Step 3)
Modify NAP profile
(Step 4)
Configure Network Access Points (NAPs)

SIP

(Step 1)
Configure IP port range
(Step 2)
Configure SIP Signaling
(Step 3)
Configure Codecs and Tone Detection
(Step 4)
Modify NAP profile
(Step 5)
Configure Network Access Points (NAPs)

SIP Advanced Features

SIP-I SIP-T
SIP Spiral
Remote NAT Traversal Local NAT Traversal

SS7 ISUP

MTP2-MTP3-ISUP

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configuring the MTP2 Layer
(Step 3)
Configuring the MTP3 Layer
(Step 4)
Configuring the ISUP Layer
(Step 5)
Modify NAP profile
(Step 6)
Configure Network Access Points (NAPs)




M2PA-MTP3-ISUP

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configuring the M2PA Layer
(Step 3)
Configuring the MTP3 Layer
(Step 4)
Configuring the ISUP Layer
(Step 5)
Modify NAP profile
(Step 6)
Configure Network Access Points (NAPs)


M3UA-ISUP

(Step 1)
Allocate Physical Interfaces
(Step 2a)
Configuring the M3UA Layer - IPSP
(Step 2b)
Configuring the M3UA Layer - SGP
(Step 3)
Configuring the ISUP Layer
(Step 4)
Modify NAP profile
(Step 5)
Configure Network Access Points (NAPs)

SS7 Advanced Features

SCCP-TCAP

MTP2-MTP3-SCCP-TCAP

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configuring the MTP2 Layer
(Step 3)
Configuring the MTP3 Layer
(Step 4)
Configuring the SCCP Layer
(Step 5)
Configuring the TCAP Layer (optional)




M2PA-MTP3-SCCP-TCAP

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configuring the M2PA Layer
(Step 3)
Configuring the MTP3 Layer
(Step 4)
Configuring the SCCP Layer
(Step 5)
Configuring the TCAP Layer (optional)


M3UA-SCCP-TCAP

(Step 1)
Allocate Physical Interfaces
(Step 2)
Configuring the M3UA Layer
(Step 3)
Configuring the SCCP Layer
(Step 4)
Configuring the TCAP Layer (optional)

H.248 MEGACO

If the Tmedia is used to forward signalling messages to the SSW, you will require to configure M2UA, M3UA or IUA before configuring H.248.

If the Tmedia is used to connect media only, then you can go straight to H.248 Configuration

M2UA

(Step 1)
Create Line Interfaces
(Step 2)
Create MTP2 links
(Step 3)
Create M2UA configuration

M3UA

(Step 1)
Create Line Interfaces
(Step 2)
Create MTP2 links
(Step 3)
Create MTP3 configuration
(Step 4)
Create M3UA configuration

IUA

(Step 1)
Create Line Interfaces
(Step 2)
Create M2UA Configuration

H.248

(Step 1)
Allocate Physical Interfaces
(Step 2)
Create IP Port Ranges
(Step 3)
Modify NAP profile
(Step 4)
Configure Network Access Points (NAPs)
(Step 5)
Configure Media Gateway for H.248 mode
(Step 6)
Add a New Media Gateway Controller
(Step 7)
Associate NAPs Resources to H.248 Configuration


Personal tools