From TBwiki

(Difference between revisions)

Latest revision as of 03:03, 18 January 2019

Introduction

This guide is designed to provide users with a scenario-based approach to installing Tmedia and Tdev systems, using the Web Portal configuration tool. This means that users must first go through the steps that are general to all installations, and subsequently follow the instructions that are specific to their particular application scenario (this corresponds to the type of service, and hardware system being set up).

Prerequisites

This document assumes that the Tmedia or Tdev devices are installed as described in their Quick Reference Guides, and in the case of the Tmedia system communication has been established with the control network.

(Note: Tmedia devices are shipped with the Tmedia Web Portal pre-installed, while Tdev devices require that Toolpack be installed as described in the Tdev installation guides.)

Furthermore, in the case of a Tdev device and the initial configuration of the Toolpack application server, the following will have been provided:

The Tdev device to which the Web Portal will first connect.
The Tdev device will have been pre-configured with its physical TDM interface.
The serial number of the Tdev device will have been entered into the configuration file.
The application software for the Tdev device will have been pre-installed on the Toolpack application server, as described in the Tdev installation guides.

This document also assumes familiarity with topics, such as ISDN signaling, SIP signaling, SS7, CAS signaling, and SIGTRAN signaling.

Key Concepts

System: A system is defined as the complete solution that is designed for a network. If a system solution is comprised of 4 TMP6400’s and a TMS1600, then the combination of these TelcoBridges devices is termed a system.
Hardware: Each TelcoBridges devices, whether it is a TMP6400, TMG3200, or TMS1600 is referred to as a hardware device or hardware adapter.
Line Interface: The physical TDM module installed on the TelcoBridges device is referred to as a line interface.

General Web Portal Applications

IMPORTANT! The Topics covered in the following table are common to all TMedia installations. Therefore, this section should be consulted before moving on to any other.

Topics covered here:

System

Access and User Management

Web Portal Access	User Management
Web Portal Access	Add User	Modify User Permission	Delete User
Connect to the Web Portal Logging Off	Creating User Groups Creating Users	Modify User Permission	Delete User

Database Backup

Create Database Backup	Restore Database
Carrying out a First Database Backup Downloading a Database Backup	Uploading a Database Backup Restoring a Database Backup

SNMP

Enable SNMP	SNMP Get/Get Next	SNMP Traps
Enabling SNMP	Configuring SNMP Agent Creating SNMP v1, SNMP v2 communities or Creating an SNMP v3 user	Configuring SNMP traps destination

Configuration

Activating a Configuration	Web Portal Profile
Activating the Configuration	Web Portal Profile

Minor Package Upgrade

Installing a Package
Retrieving a software release Uploading a software release Activating a software release

Upload license

Installing a Package
Retrieving a license Uploading a license

Statistics

Configuration	Profile	Graphs
Configuring Statistics Polling	Creating Statistics Profiles Enabling Statistics Profiles	Generating Graphs

Audit Logs

Audit Logs
Working with Audit Logs

VoIP Bonding

VoIP Bonding
Enabling VoIP Bonding

Note: Web portal configuration for VoIP bonding is not yet available.

Hardware

New Hardware

Add telecom hardware	Add TMS hardware	Add 1+1 group	Add N+1 group
Add telecom hardware	Add TMS hardware	Add 1+1 group	Add N+1 patch panel Add N+1 group

TDM Network

(Step 1) Allocate Physical Interfaces	(Step 2) System Clock
Create Line Interfaces Create Line Services	System Clock

IP Network

(Step 1) IP Interfaces	Create an IP port range
Configuring VoIP Interfaces	Create an IP port range

Protocol Stacks

ISDN NFAS

(Step 1) Allocate Physical Interfaces	(Step 2) Configure ISDN-PRI Signaling	(Step 3) Modify NAP profile	(Step 4) Configure Network Access Points (NAPs)
Create Line interfaces Create Line Services	Configure an ISDN stack OR Configure NFAS	Modify profile	Allocate an ISDN NAP

ISDN Advanced Features

ISDN Overlap Sending
ISDN NFAS Overlap Parameters

CAS

(Step 1) Allocate Physical Interfaces	(Step 2) Configuring a CAS stack	(Step 3) Modify NAP profile	(Step 4) Configure Network Access Points (NAPs)
Create Line Interfaces Create Line services	Copy variant script Create CAS stack Edit the CAS R1 or CAS R2 script to adapt the variant Select CAS R1 tone type Set CAS R2 backward digits string	Modify profile	Create a CAS NAP

SIP

(Step 1) Configure IP port range	(Step 2) Configure SIP Signaling	(Step 3) Configure Codecs and Tone Detection	(Step 4) Modify NAP profile	(Step 5) Configure Network Access Points (NAPs)
Create an IP port range	Create a SIP stack Create a SIP transport server Create a service access point (SAP)	Access profiles and validate settings	Modify profile	Allocate a SIP NAP

SIP Advanced Features

SIP-I SIP-T
Enabling SIP-I SIP-T

SIP Spiral
Enabling SIP Spiral

Remote NAT Traversal	Local NAT Traversal
Enabling Remote NAT Traversal	Enabling Local NAT Traversal

DNS
Enabling DNS

SS7 ISUP

MTP2-MTP3-ISUP

(Step 1) Allocate Physical Interfaces	(Step 2) Configuring the MTP2 Layer	(Step 3) Configuring the MTP3 Layer	(Step 4) Configuring the ISUP Layer	(Step 5) Modify NAP profile	(Step 6) Configure Network Access Points (NAPs)
Create a new line interface Create a new line service	Create an MTP2 Configuration Create an MTP2 Link	Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Point Code Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route	Create an ISUP Stack Create an ISUP Network Create an ISUP User Part Create an ISUP Interface Create ISUP CIC Groups	Modify profile	Create an ISUP NAP

M2PA-MTP3-ISUP

(Step 1) Allocate Physical Interfaces	(Step 2) Configuring the M2PA Layer	(Step 3) Configuring the MTP3 Layer	(Step 4) Configuring the ISUP Layer	(Step 5) Modify NAP profile	(Step 6) Configure Network Access Points (NAPs)
Create a new line interface Create a new line service	Edit the SCTP Configuration Create an M2PA Configuration Create an M2PA SAP Add M2PA Links	Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Point Code Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route	Create an ISUP Stack Create an ISUP Network Create an ISUP User Part Create an ISUP Interface Create ISUP CIC Groups	Modify profile	Create an ISUP NAP

M3UA-ISUP

(Step 1a) Configuring the M3UA Layer - IPSP	(Step 1b) Configuring the M3UA Layer - ASP	(Step 1c) Configuring the M3UA Layer - SGP	(Step 2) Configuring the ISUP Layer	(Step 3) Modify NAP profile	(Step 4) Configure Network Access Points (NAPs)
Edit the SCTP Configuration Create SS7 Point Codes Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create an M3UA Route	Edit the SCTP Configuration Create SS7 Point Codes Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create an M3UA Route	Edit the SCTP Configuration Create SS7 Point Codes Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create an M3UA Route	Create an ISUP Stack Create an ISUP Network Create an ISUP User Part Create an ISUP Interface Create ISUP CIC Groups	Modify profile	Create an ISUP NAP

SS7 Advanced Features

Configuring SPIROU
Modifying Profile Modifying Gateway Configurations Modifying ISUP Stack Modifying ISUP Userpart Optional modifications

SCCP-TCAP

MTP2-MTP3-SCCP-TCAP

(Step 1) Allocate Physical Interfaces	(Step 2) Configuring the MTP2 Layer	(Step 3) Configuring the MTP3 Layer	(Step 4) Configuring the SCCP Layer	(Step 5) Configuring the TCAP Layer (optional)
Create a new line interface Create a new line service	Create an MTP2 Configuration Create an MTP2 Link	Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Point Code Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route	Create an SCCP Stack Create an SCCP Network Create an SCCP Userpart Create an SCCP LSAP Create an SCCP Route Create an SCCP SSN Create an SCCP GTT Association Create an SCCP GTT Address Map	Create a TCAP Stack Create a TCAP Userpart Activating the Configuration

M2PA-MTP3-SCCP-TCAP

(Step 1) Allocate Physical Interfaces	(Step 2) Configuring the M2PA Layer	(Step 3) Configuring the MTP3 Layer	(Step 4) Configuring the SCCP Layer	(Step 5) Configuring the TCAP Layer (optional)
Create a new line interface Create a new line service	Edit the SCTP Configuration Create an M2PA Configuration Create an M2PA SAP Add M2PA Links	Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Point Code Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route	Create an SCCP Stack Create an SCCP Network Create an SCCP Userpart Create an SCCP LSAP Create an SCCP Route Create an SCCP SSN Create an SCCP GTT Association Create an SCCP GTT Address Map	Create a TCAP Stack Create a TCAP Userpart Activating the Configuration

M3UA-SCCP-TCAP

(Step 1) Configuring the M3UA Layer	(Step 2) Configuring the SCCP Layer	(Step 3) Configuring the TCAP Layer (optional)
Edit the SCTP Configuration Create SS7 Point Codes Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create an M3UA Route	Create an SCCP Stack Create an SCCP Network Create an SCCP Userpart Create an SCCP LSAP Create an SCCP Route Create an SCCP SSN Create an SCCP GTT Association Create an SCCP GTT Address Map	Create a TCAP Stack Create a TCAP Userpart Activating the Configuration

H.248 MEGACO

If the Tmedia is used to forward signalling messages to the SSW, you will require to configure M2UA, M3UA or IUA before configuring H.248.

If the Tmedia is used to connect media only, then you can go straight to H.248 Configuration

M2UA

(Step 1) Create Line Interfaces	(Step 2) Create MTP2 links	(Step 3) Create M2UA configuration
Create line interfaces Create line services	Create an MTP2 Configuration Create MTP2 Links	Edit the SCTP Configuration Create an M2UA Configuration Create an M2UA SAP Create an M2UA Cluster Create M2UA Links Create M2UA Peers

M3UA

(Step 1) Create Line Interfaces	(Step 2) Create MTP2 links	(Step 3) Create MTP3 configuration	(Step 4) Create M3UA configuration
Create line interfaces Create line services	Create an MTP2 Configuration Create MTP2 Links	Create SS7 Point Codes Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route	Edit the SCTP Configuration Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create an M3UA Route

IUA

(Step 1) Create Line Interfaces	(Step 2) Create M2UA Configuration
Create Line Interfaces Create Line services	Edit the SCTP Configuration Create an IUA Configuration Create an IUA SAP Create an IUA Cluster Create IUA Links Create IUA Peers

H.248

(Step 1) Allocate TDM Physical Interfaces	(Step 2) Create IP Port Ranges	(Step 3) Modify NAP profile	(Step 4) Configure Network Access Points (NAPs)
Create line interfaces Create line services	Create IP port ranges	Modify profile	Allocate a VoIP NAP Allocate a TDM NAP Allocate a CAS Stack and NAP
(Step 5) Configure Media Gateway for H.248 mode	(Step 6) Add a New Media Gateway Controller	(Step 7) Associate NAPs Resources to H.248 Configuration
Configure the Media Gateway for H.248 mode Create a new H.248 configuration	Add a new media gateway controller (MGC)	Associate the NAPs with the H.248 configuration Select timeslots for the TDM interfaces

CDR (Call Detail Record)

Text CDR	RADIUS
Enabling CDR	Enabling RADIUS Configuring RADIUS client Adding RADIUS server(s)

Fax

FAX passthrough	FAX T.38
Configure Fax Relay Configure Fax Passthrough	Configure Fax Relay Configure Fax T38

Routes

Static Route

Add routes
Create a first call route

Routing Script

TelcoBridges provides a wide variety of routing script examples which customers can apply directly in their web configuration according to their needs by following just a few simple steps. Please select one of the following examples according to your needs. You may modify it when necessary.

*Flexible NOA: Remap the Calling/Called NOA flexibly based on the routes. It should cover most of the NOA requests since the routes include the calling/called remapping as well.

*Prefix NOA: Remapp Calling/Called NOA according to the prefix of the calling/called number, manipulate calling/called number. For calling number, if it is a privacy call, use the number in P-Asserted-Identity line or Remote-Party-ID line as the calling number to remap the NOA and do the manipulation.

*Priority and Load-sharing Routing:This shows how to add Priority and Load sharing to any Routing scripts. This is a powerful script that allows to regroup Routes of the same kind, distribute load among them and prioritize one group versus another. Alternatively, you can do the same on NAPs. You will use two additional parameters in the routes: group and weight.
group serves as two purpose:

priority: a lower value will have higher priority
matching routes of the same group will load share according to the weight parameter

weight will load share calls among matching routes of the same group

For the procedure to add Priority and Load-sharing Routing to existing routing script, please refer to the below link:
*Adding_Load_Sharing_to_Routing_Script

Flexible NOA	Prefix NOA	Priority and Load-sharing Routing
Create new routing script Enable Flexible NOA script Add NOA columns in routes Enable routing script in Gateway Activate configuration	Create new routing script Import customized routing script Enable routing script in Gateway Activate configuration	Create new routing script Enable Priority and Load-sharing Routing script Add group and weight columns in routes Enable routing script in Gateway Activate configuration

Audio Prompts
Audio Prompts

Label Routing

This section assumes:

The routing script is already implemented (you just need to add the label routing functionality)
The routeset definition and digimap files are already created

Add label routing functionality
Add Label Routing to script Create Database Files Assign Routing/Script Files to the Gateway Application Add the Digit Map Files to the System Add the Routset Definition Files to the System Assign Defintion/Digitmap Files on a per NAP Basis Generate Dynamic Routes Activate configuration

Update definition/digitmap files
Update the Digitmap Files Update the Routeset Definition Files Generate Dynamic Routes Activate configuration

RADIUS Authorization and Authentication

RADIUS
Configure RADIUS client Add RADIUS authorization server Configure RADIUS authorization

RADIUS (with custom dictionary)
Import RADIUS Custom Dictionary Configure RADIUS Client Add RADIUS Authorization Server Create New Routing Script Configure RADIUS Authorization Enable Routing Script

Lawful Interception

Lawful Interception
Verify Lawful Interception Prerequisite Import a Lawful Interception CSV File Create New Routing Script Enable Lawful Interception in Routing script Enable Routing Script Configure Lawful Agencies

Troubleshooting

Call Trace

Call trace
Configure call trace Retrieve call trace

Test Call

Test Call
Creating a Test Call

Target Recording

Activate Call Recording	Start the Stream Server	Access the Recorded Files
Enabling the Recording of Calls	Start Stream Server	Accessing the Recording

VoIP Ethernet Capture

Capturing Ethernet Traffic
Capturing on a TMG800 Capturing on a TMG3200 Capturing on a TMG7800

Status Menus

The Web Portal configuration tool will guide you through a number of status menus, each of which indicate the current state of a certain hardware service (assuming said service has been configured). The following table contains the general conventions of the Web Portal's display (A), as well as a variety of specific status menus (B).

(A) Menus Overview	(B) Individual Menu Descriptions
Tmedia Status Menus Navigation Status Screen Conventions	System Adapters and IP Interfaces 1+1 N+1 Hosts Applications TDM Lines Line Interfaces SCTP SS7 MTP2 SS7 M2UA SS7 IUA SS7 M2PA SS7 M3UA SS7 MTP3 SS7 ISUP SS7 SCCP SS7 TCAP ISDN NFAS CAS SIP Clock Clock Status List TMS NAP NAP Status List H.248 RADIUS

@@ Line 14: / Line 14: @@
 *The application software for the Tdev device will have been pre-installed on the Toolpack application server, as described in the [[Tmedia_Installation#Tdev|Tdev installation guides]].
-This document also assumes familiarity with topics, such as [[ISDN]] signaling, [[SIP]] signaling, [[SS7]], [[CAS|CAS R2]] signaling, and [[SIGTRAN]] signaling.
+This document also assumes familiarity with topics, such as [[ISDN]] signaling, [[SIP]] signaling, [[SS7]], [[CAS|CAS]] signaling, and [[SIGTRAN]] signaling.
 ==Key Concepts==
@@ Line 74: / Line 73: @@
 *[[Toolpack:Uploading a Database Backup B|Uploading a Database Backup]]
 *[[Toolpack:Restoring a Database Backup B|Restoring a Database Backup]]
+|}
+==SNMP==
+{| cellpadding="5" border="1" class="wikitable"
+|-
+! width="200" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Enable SNMP
+! width="200" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | SNMP Get/Get Next
+! width="200" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | SNMP Traps
+|-
+| valign="top" |
+* [[Activating_tbSnmpAgent|Enabling SNMP]]
+| valign="top" |
+* [[Toolpack:Configuring_tbSnmpAgent_A|Configuring SNMP Agent]]
+* [[Toolpack:Creating_an_SNMPv1/SNMPv2_Community_A|Creating SNMP v1, SNMP v2 communities]]
+or
+* [[Toolpack:Creating_an_SNMPv3_User_A|Creating an SNMP v3 user]]
+| valign="top" |
+* [[Toolpack:Creating_an_SNMP_Trap_Destination_A|Configuring SNMP traps destination]]
 |}
@@ Line 97: / Line 114: @@
 *[[Toolpack:Uploading_a_Release_A|Uploading a software release]]
 *[[Toolpack:Activating_a_Release_A|Activating a software release]]
+|}
+</div>
+<div id="Upload license">
+==Upload license==
+{| cellpadding="5" border="1" class="wikitable"
+|-
+! width="200" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Installing a Package
+|-
+| valign="top" |
+*[[Toolpack:Retreiving_a_License_A|Retrieving a license]]
+*[[Toolpack:Uploading_a_License_A|Uploading a license]]
 |}
 </div>
@@ Line 125: / Line 154: @@
 |}
+==VoIP Bonding==
+{| cellpadding="5" border="1" class="wikitable"
+|-
+! width="200" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | VoIP Bonding
+|-
+| valign="top" |
+*[[Toolpack:Enabling_VoIP_Bonding_A|Enabling VoIP Bonding]]
+|}
+Note: Web portal configuration for VoIP bonding is not yet available.
 =Hardware=
@@ Line 144: / Line 183: @@
 *[[Toolpack:Creating_a_1+1_Group_A|Add 1+1 group]]
 | valign="top" |
+*[[Toolpack:Creating_a_N+1_Patch_Panel_A|Add N+1 patch panel]]
 *[[Toolpack:Creating_a_N+1_Group_A|Add N+1 group]]
 |}
@@ Line 172: / Line 212: @@
 *[[Toolpack:Configuring_VoIP_Interfaces B|Configuring VoIP Interfaces]]
 | valign="top" |
-*[[Toolpack:Creating_an_IP_Port_Range A|Create an IP port range]]
+*[[Toolpack:Creating_an_IP_Port_Range B|Create an IP port range]]
 |}
@@ Line 217: / Line 257: @@
 |-
 | valign="top" |
-*[[Toolpack:Configuring_Overlap A|ISDN NFAS Overlap Parameters]]
+*[[Toolpack:Configuring_Overlap A|''ISDN NFAS Overlap Parameters'']]
 |}
@@ Line 223: / Line 263: @@
 <br><br>
-==''CASR2''==
+==CAS==
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 229: / Line 269: @@
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring a CAS R2 stack
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring a CAS stack
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Modify NAP profile
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Network Access Points (NAPs)
@@ Line 238: / Line 278: @@
 *[[Toolpack:Creating_a_Line_Service B|Create Line services]]
 | valign="top" |
-*[[Toolpack:Copy variant script A|Copy variant script]]
+*[[Toolpack:Copy variant script B|Copy variant script]]
-*[[Toolpack:Create CAS R2 stack A|Create CAS R2 stack]]
+*[[Toolpack:Create CAS R2 stack B|Create CAS stack]]
-*[[Toolpack:Setting CAS R2 BACK DIGITS variable A|Set backward digits string]]
+*Edit the [[CASr1_scripting|CAS R1]] or [[CAS R2 scripting|CAS R2]] script to adapt the variant
+**[[CASr1_scripting#TONE_USE_DTMF|Select CAS R1 tone type]]
+**[[Toolpack:Setting CAS R2 BACK DIGITS variable B|Set CAS R2 backward digits string]]
 | valign="top" |
 *[[Toolpack:Modify_NAP_profile B|Modify profile]]
 | valign="top" |
-*[[Toolpack:Creating_a_CAS_R2_NAP A|Create a CASR2 NAP]]
+*[[Toolpack:Creating_a_CAS_R2_NAP B|Create a CAS NAP]]
 |}
-==''SIP''==
+==SIP==
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 262: / Line 304: @@
 | valign="top" |
-*[[Toolpack:Creating_a_SIP_Stack A|Create a SIP stack]]
+*[[Toolpack:Creating_a_SIP_Stack B|Create a SIP stack]]
-*[[Toolpack:Creating_a_SIP_Transport_Server A|Create a SIP transport server]]
+*[[Toolpack:Creating_a_SIP_Transport_Server B|Create a SIP transport server]]
-*[[Toolpack:Creating_a_Service_Access_Point_(SAP) A|Create a service access point (SAP)]]
+*[[Toolpack:Creating_a_Service_Access_Point_(SAP) B|Create a service access point (SAP)]]
 | valign="top" |
-*[[Toolpack:Accessing_Codec_and_Tone_Detection_Profiles_and_Validating_Settings A|Access profiles and validate settings]]
+*[[Toolpack:Accessing_Codec_and_Tone_Detection_Profiles_and_Validating_Settings B|Access profiles and validate settings]]
 | valign="top" |
@@ Line 273: / Line 315: @@
 | valign="top" |
-*[[Toolpack:Allocating_a_SIP_Network_Access_Point_(NAP) A|Allocate a SIP NAP]]
+*[[Toolpack:Allocating_a_SIP_Network_Access_Point_(NAP) B|Allocate a SIP NAP]]
 |}
-===''SIP Advanced Features''===
+===SIP Advanced Features===
 <div class="mw-collapsible mw-collapsed" data-collapsetext="SIP-I SIP-T" data-expandtext="SIP-I SIP-T" style="width: 400px;">
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 284: / Line 326: @@
 |-
 | valign="top" |
-*[[Enabling_SIP_I_SIP_T_A|Enabling SIP-I SIP-T]]
+*[[Enabling_SIP_I_SIP_T_B|Enabling SIP-I SIP-T]]
 |}
 </div>
@@ Line 293: / Line 335: @@
 |-
 | valign="top" |
-*[[Enabling_SIP_Spiral_A|Enabling SIP Spiral]]
+*[[Enabling_SIP_Spiral_B|Enabling SIP Spiral]]
 |}
@@ Line 309: / Line 351: @@
 | valign="top" |
 *[[Enabling_Local_NAT_Traversal_A|Enabling Local NAT Traversal]]
+|}
+</div>
+<div class="mw-collapsible mw-collapsed" data-collapsetext="DNS" data-expandtext="DNS" style="width: 400px;">
+{| cellpadding="5" border="1" class="wikitable"
+|-
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | DNS
+|-
+| valign="top" |
+*[[Toolpack:Configuring_DNS_Parameters_A|Enabling DNS]]
 |}
 </div>
@@ Line 314: / Line 366: @@
 ==SS7 ISUP==
-===''MTP2-MTP3-ISUP''===
+===MTP2-MTP3-ISUP===
@@ Line 332: / Line 384: @@
 | valign="top" |
-*[[Toolpack:Creating_an_MTP2_Configuration A|Create an MTP2 Configuration]]
+*[[Toolpack:Creating_an_MTP2_Configuration B|Create an MTP2 Configuration]]
 *[[Toolpack:Creating_MTP2_Links A|Create an MTP2 Link]]
 | valign="top" |
-*[[Toolpack:Creating_an_MTP3_Configuration B|Create an MTP3 Configuration]]
+*[[Toolpack:Creating_an_MTP3_Configuration C|Create an MTP3 Configuration]]
 *[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
-**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
+**[[Toolpack:Creating_SS7_Point_Codes B|Create an MTP3 Point Code]]
 **[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 ***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
@@ Line 346: / Line 398: @@
 | valign="top" |
-*[[Toolpack:Creating_an_ISUP_Stack A|Create an ISUP Stack]]
+*[[Toolpack:Creating_an_ISUP_Stack B|Create an ISUP Stack]]
 *[[Toolpack:Creating_an_ISUP_Network A|Create an ISUP Network]]
 *[[Toolpack:Creating_an_ISUP_User_Part A|Create an ISUP User Part]]
@@ Line 357: / Line 409: @@
 | valign="top" |
-*[[Toolpack:Creating_a_NAP_(SIGTRAN)_A|Create an ISUP NAP]]
+*[[Toolpack:Creating_a_NAP_(SIGTRAN)_B|Create an ISUP NAP]]
 |}
-===''M2PA-MTP3-ISU''P===
+===M2PA-MTP3-ISUP===
@@ Line 379: / Line 431: @@
 | valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
-*[[Toolpack:Creating the M2PA Configuration A|Create an M2PA Configuration]]
+*[[Toolpack:Creating the M2PA Configuration B|Create an M2PA Configuration]]
-**[[Toolpack:Creating an M2PA SAP A|Create an M2PA SAP]]
+**[[Toolpack:Creating an M2PA SAP B|Create an M2PA SAP]]
 **[[Toolpack:Adding M2PA Links A|Add M2PA Links]]
 | valign="top" |
-*[[Toolpack:Creating_an_MTP3_Configuration B|Create an MTP3 Configuration]]
+*[[Toolpack:Creating_an_MTP3_Configuration C|Create an MTP3 Configuration]]
 *[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
-**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
+**[[Toolpack:Creating_SS7_Point_Codes B|Create an MTP3 Point Code]]
 **[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 ***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
@@ Line 394: / Line 446: @@
 | valign="top" |
-*[[Toolpack:Creating_an_ISUP_Stack A|Create an ISUP Stack]]
+*[[Toolpack:Creating_an_ISUP_Stack B|Create an ISUP Stack]]
 *[[Toolpack:Creating_an_ISUP_Network A|Create an ISUP Network]]
 *[[Toolpack:Creating_an_ISUP_User_Part A|Create an ISUP User Part]]
@@ Line 404: / Line 456: @@
 | valign="top" |
-*[[Toolpack:Creating_a_NAP_(SIGTRAN)_A|Create an ISUP NAP]]
+*[[Toolpack:Creating_a_NAP_(SIGTRAN)_B|Create an ISUP NAP]]
 |}
-===''M3UA-ISUP''===
+===M3UA-ISUP===
 {| cellpadding="5" border="1" class="wikitable"
 |-
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1a) <br>Configuring the M3UA Layer - IPSP
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the M3UA Layer
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1b) <br>Configuring the M3UA Layer - ASP
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the ISUP Layer
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1c) <br>Configuring the M3UA Layer - SGP
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Modify NAP profile
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the ISUP Layer
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure Network Access Points (NAPs)
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Modify NAP profile
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Network Access Points (NAPs)
 |-
 | valign="top" |
-*[[Toolpack:Creating_a_Line_Interface B|Create a new line interface]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
-*[[Toolpack:Creating_a_Line_Service B|Create a new line service]]
-| valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 *[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
-*[[Toolpack:Creating an M3UA Configuration (IPSP) A|Create an M3UA Configuration]]
+*[[Toolpack:Creating an M3UA Configuration (IPSP) B|Create an M3UA Configuration]]
 **[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
 **[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
-**[[Toolpack:Creating an M3UA User Part A|Create an M3UA User Part]]
+**[[Toolpack:Creating_an_M3UA_User_Part_(IPSP)_A|Create an M3UA User Part]]
 **[[Toolpack:Creating an M3UA Peer Signalling Process (IPSP) A|Create an M3UA Peer Signalling Process]]
 **[[Toolpack:Creating an M3UA Peer Server A|Create an M3UA Peer Server]]
@@ Line 436: / Line 485: @@
 | valign="top" |
-*[[Toolpack:Creating_an_ISUP_Stack A|Create an ISUP Stack]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
+*[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
+*[[Toolpack:Creating an M3UA Configuration ASP B|Create an M3UA Configuration]]
+**[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
+**[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
+**[[Toolpack:Creating_an_M3UA_User_Part_(IPSP)_A|Create an M3UA User Part]]
+**[[Toolpack:Creating an M3UA Peer Application Server Process (ASP) A|Create an M3UA Peer Signalling Process]]
+**[[Toolpack:Creating an M3UA Peer Server (ASP) A|Create an M3UA Peer Server]]
+**[[Toolpack:Creating an M3UA Route (ASP) A|Create an M3UA Route]]
+| valign="top" |
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
+*[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
+*[[Toolpack:Creating an M3UA Configuration SGP B|Create an M3UA Configuration]]
+**[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
+**[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
+**[[Toolpack:Creating an M3UA User Part (SGP) A|Create an M3UA User Part]]
+**[[Toolpack:Creating an M3UA Peer Signalling Process (SGP) A|Create an M3UA Peer Signalling Process]]
+**[[Toolpack:Creating an M3UA Peer Server (SGP) A|Create an M3UA Peer Server]]
+**[[Toolpack:Creating an M3UA Route (SGP) A|Create an M3UA Route]]
+| valign="top" |
+*[[Toolpack:Creating_an_ISUP_Stack B|Create an ISUP Stack]]
 *[[Toolpack:Creating_an_ISUP_Network A|Create an ISUP Network]]
 *[[Toolpack:Creating_an_ISUP_User_Part A|Create an ISUP User Part]]
@@ Line 446: / Line 517: @@
 | valign="top" |
-*[[Toolpack:Creating_a_NAP_(SIGTRAN)_A|Create an ISUP NAP]]
+*[[Toolpack:Creating_a_NAP_(SIGTRAN)_B|Create an ISUP NAP]]
 |}
@@ Line 467: / Line 538: @@
 </div>
-==''SCCP-TCAP''==
+==SCCP-TCAP==
-===''MTP2-MTP3-SCCP-TCAP''===
+===MTP2-MTP3-SCCP-TCAP===
@@ Line 488: / Line 559: @@
 | valign="top" |
-*[[Toolpack:Creating_an_MTP2_Configuration A|Create an MTP2 Configuration]]
+*[[Toolpack:Creating_an_MTP2_Configuration B|Create an MTP2 Configuration]]
 *[[Toolpack:Creating_MTP2_Links A|Create an MTP2 Link]]
 | valign="top" |
-*[[Toolpack:Creating_an_MTP3_Configuration B|Create an MTP3 Configuration]]
+*[[Toolpack:Creating_an_MTP3_Configuration C|Create an MTP3 Configuration]]
 *[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
-**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
+**[[Toolpack:Creating_SS7_Point_Codes B|Create an MTP3 Point Code]]
 **[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 ***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
@@ Line 515: / Line 586: @@
 *[[Toolpack:Creating_a_TCAP_Stack A|Create a TCAP Stack]]
 **[[Toolpack:Creating_a_TCAP_Userpart A| Create a TCAP Userpart]]
-*[[Toolpack:Activating_the_Configuration A|Activating the Configuration]]
+*[[Toolpack:Activating_the_Configuration B|Activating the Configuration]]
 |}
-===''M2PA-MTP3-SCCP-TCAP''===
+===M2PA-MTP3-SCCP-TCAP===
@@ Line 536: / Line 607: @@
 | valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
-*[[Toolpack:Creating the M2PA Configuration A|Create an M2PA Configuration]]
+*[[Toolpack:Creating the M2PA Configuration B|Create an M2PA Configuration]]
-**[[Toolpack:Creating an M2PA SAP A|Create an M2PA SAP]]
+**[[Toolpack:Creating an M2PA SAP B|Create an M2PA SAP]]
 **[[Toolpack:Adding M2PA Links A|Add M2PA Links]]
 | valign="top" |
-*[[Toolpack:Creating_an_MTP3_Configuration B|Create an MTP3 Configuration]]
+*[[Toolpack:Creating_an_MTP3_Configuration C|Create an MTP3 Configuration]]
 *[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
-**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
+**[[Toolpack:Creating_SS7_Point_Codes B|Create an MTP3 Point Code]]
 **[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 ***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
@@ Line 563: / Line 634: @@
 *[[Toolpack:Creating_a_TCAP_Stack A|Create a TCAP Stack]]
 **[[Toolpack:Creating_a_TCAP_Userpart A| Create a TCAP Userpart]]
-*[[Toolpack:Activating_the_Configuration A|Activating the Configuration]]
+*[[Toolpack:Activating_the_Configuration B|Activating the Configuration]]
 |}
-===''M3UA-SCCP-TCAP''===
+===M3UA-SCCP-TCAP===
 {| cellpadding="5" border="1" class="wikitable"
 |-
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Configuring the M3UA Layer
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the M3UA Layer
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the SCCP Layer
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the SCCP Layer
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the TCAP Layer (optional)
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the TCAP Layer (optional)
 |-
 | valign="top" |
-*[[Toolpack:Creating_a_Line_Interface B|Create a new line interface]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
-*[[Toolpack:Creating_a_Line_Service B|Create a new line service]]
-| valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 *[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
-*[[Toolpack:Creating an M3UA Configuration (IPSP) A|Create an M3UA Configuration]]
+*[[Toolpack:Creating an M3UA Configuration (IPSP) B|Create an M3UA Configuration]]
 **[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
 **[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
@@ Line 606: / Line 672: @@
 *[[Toolpack:Creating_a_TCAP_Stack A|Create a TCAP Stack]]
 **[[Toolpack:Creating_a_TCAP_Userpart A| Create a TCAP Userpart]]
-*[[Toolpack:Activating_the_Configuration A|Activating the Configuration]]
+*[[Toolpack:Activating_the_Configuration B|Activating the Configuration]]
 |}
-==''H.248 MEGACO''==
+==H.248 MEGACO==
 If the Tmedia is used to forward signalling messages to the SSW, you will require to configure M2UA, M3UA or IUA before configuring H.248.
@@ Line 616: / Line 682: @@
 If the Tmedia is used to connect media only, then you can go straight to [[#H.248|H.248 Configuration]]
-===''M2UA''===
+===M2UA===
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 632: / Line 698: @@
 | valign="top" |
-*[[Toolpack:Creating an MTP2 Configuration A|Create an MTP2 Configuration]]
+*[[Toolpack:Creating an MTP2 Configuration B|Create an MTP2 Configuration]]
 **[[Toolpack:Creating MTP2 Links A|Create MTP2 Links]]
 | valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
-*[[Toolpack:Creating the M2UA Configuration A|Create an M2UA Configuration]]
+*[[Toolpack:Creating the M2UA Configuration B|Create an M2UA Configuration]]
 **[[Toolpack:Creating an M2UA SAP A|Create an M2UA SAP]]
 **[[Toolpack:Creating an M2UA Cluster A|Create an M2UA Cluster]]
@@ Line 646: / Line 712: @@
 |}
-===''M3UA''===
+===M3UA===
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 661: / Line 727: @@
 | valign="top" |
-*[[Toolpack:Creating an MTP2 Configuration A|Create an MTP2 Configuration]]
+*[[Toolpack:Creating an MTP2 Configuration B|Create an MTP2 Configuration]]
 *[[Toolpack:Creating MTP2 Links A|Create MTP2 Links]]
 | valign="top" |
 *[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
-*[[Toolpack:Creating an MTP3 Configuration B|Create an MTP3 Configuration]]
+*[[Toolpack:Creating an MTP3 Configuration C|Create an MTP3 Configuration]]
 **[[Toolpack:Creating an MTP3 Network A|Create an MTP3 Network]]
 **[[Toolpack:Creating an MTP3 Linkset A|Create an MTP3 Linkset]]
@@ Line 673: / Line 739: @@
 | valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
 *[[Toolpack:Creating an M3UA Configuration (SGP) A|Create an M3UA Configuration]]
 **[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
@@ Line 684: / Line 750: @@
 |}
-===''IUA''===
+===IUA===
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 698: / Line 764: @@
 | valign="top" |
-*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
+*[[Toolpack:Creating the SCTP Configuration B|Edit the SCTP Configuration]]
-*[[Toolpack:Creating the IUA Configuration A|Create an IUA Configuration]]
+*[[Toolpack:Creating the IUA Configuration B|Create an IUA Configuration]]
 **[[Toolpack:Creating an IUA SAP A|Create an IUA SAP]]
 **[[Toolpack:Creating an IUA Cluster A|Create an IUA Cluster]]
@@ Line 707: / Line 773: @@
 |}
-===''H.248''===
+===H.248===
 {| cellpadding="5" border="1" class="wikitable"
 |-
-! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate TDM Physical Interfaces
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Create IP Port Ranges
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Modify NAP profile
@@ Line 723: / Line 789: @@
 | valign="top" |
-*[[Toolpack:Creating_an_IP_Port_Range A|Create IP port ranges]]
+*[[Toolpack:Creating_an_IP_Port_Range B|Create IP port ranges]]
 | valign="top" |
-*[[Toolpack:Modify_NAP_profile A|Modify profile]]
+*[[Toolpack:Modify_NAP_profile B|Modify profile]]
 | valign="top" |
-*[[Toolpack:Allocating_a_VoIP_Network_Access_Point_(NAP) A|Allocate a VoIP NAP]]
+*[[Toolpack:Allocating_a_VoIP_Network_Access_Point_(NAP) B|Allocate a VoIP NAP]]
-*[[Toolpack:Allocating_a_TDM_Network_Access_Point_(NAP) A|Allocate a TDM NAP]]
+*[[Toolpack:Allocating_a_TDM_Network_Access_Point_(NAP) B|Allocate a TDM NAP]]
+*[[Web_Portal_Tutorial_Guide_v2.7#CAS|Allocate a CAS Stack and NAP]]
 |-
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure Media Gateway for H.248 mode
@@ Line 738: / Line 805: @@
 | valign="top" |
-*[[Toolpack:Configure the Media_Gateway_for_H248_Mode A|Configure the Media Gateway for H.248 mode]]
+*[[Toolpack:Configure the Media_Gateway_for_H248_Mode B|Configure the Media Gateway for H.248 mode]]
-*[[Toolpack:Creating_an_H.248_Configuration A|Create a new H.248 configuration]]
+*[[Toolpack:Creating_an_H.248_Configuration B|Create a new H.248 configuration]]
 | valign="top" |
 *[[Toolpack:Adding_a_Media_Gateway_Controller_(MGC) A|Add a new media gateway controller (MGC)]]
 | valign="top" |
-*[[Toolpack:Associating_NAPs_with_an_H.248_Configuration A|Associate the NAPs with the H.248 configuration]]
+*[[Toolpack:Associating_NAPs_with_an_H.248_Configuration B|Associate the NAPs with the H.248 configuration]]
 *[[Toolpack:Selecting_Timeslots_for_TDM_Interfaces A|Select timeslots for the TDM interfaces]]
@@ Line 751: / Line 818: @@
 <div id="CDR">
-=''CDR (Call Detail Record)''=
+=CDR (Call Detail Record)=
 {| cellpadding="5" border="1" class="wikitable"
 |-
@@ Line 759: / Line 826: @@
 | valign="top" |
-*[[Text_cdr|Text CDR]]
+*[[Toolpack:Enabling CDR A|Enabling CDR]]
 | valign="top" |
-*[[Toolpack:Enabling RADIUS A|Enabling RADIUS]]
+*[[Toolpack:Enabling RADIUS B|Enabling RADIUS]]
 *[[Toolpack:Configuring_RADIUS_client A|Configuring RADIUS client]]
 *[[Toolpack:Adding_RADIUS_server A|Adding RADIUS server(s)]]
@@ Line 787: / Line 855: @@
 =Routes=
-==''Static Route''==
+==Static Route==
 {| cellpadding="5" border="1" class="wikitable"
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Add routes
 |-
 | valign="top" |
-*[[Toolpack:Creating_a_First_Call_Route A|Create a first call route]]
+*[[Toolpack:Creating_a_First_Call_Route B|Create a first call route]]
 |}
@@ Line 802: / Line 870: @@
 '''*Prefix NOA:''' Remapp Calling/Called NOA according to the prefix of the calling/called number, manipulate calling/called number. For calling number, if it is a privacy call, use the number in P-Asserted-Identity line or Remote-Party-ID line as the calling number to remap the NOA and do the manipulation.
+'''*Priority and Load-sharing Routing:'''This shows how to add Priority and Load sharing to any Routing scripts. This is a powerful script that allows to regroup Routes of the same kind, distribute load among them and prioritize one group versus another.  Alternatively, you can do the same on NAPs.  You will use two additional parameters in the routes: '''group''' and '''weight'''.<br />
+'''group''' serves as two purpose:
+# priority: a lower value will have higher priority
+# matching routes of the same group will load share according to the weight parameter
+'''weight''' will load share calls among matching routes of the same group
+<br>
+ For the procedure to add Priority and Load-sharing Routing to existing routing script, please refer to the below link:
+ *[[Adding_Load_Sharing_to_Routing_Script|Adding_Load_Sharing_to_Routing_Script]]
 {| cellpadding="5" border="1" class="wikitable"
@@ Line 807: / Line 883: @@
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Flexible NOA
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Prefix NOA
+! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Priority and Load-sharing Routing
 |-
 | valign="top" |
 *[[Toolpack:Create_New_Routing_Script_B|Create new routing script]]
-*[[Import_Customized_Routing_Script_A|Import customized routing script]]
+*[[Enable_Flexible_NOA_Routing_Script_A|Enable Flexible NOA script]]
-*[[Add_NOA_Columns_in_Routes_A|Add NOA columns in routes]]
+*[[Add_NOA_Columns_in_Routes_B|Add NOA columns in routes]]
-*[[Enable_Routing_Script_A|Enable routing script]]
+*[[Enable_Routing_Script_B|Enable routing script in Gateway]]
-*[[Activate_Configuration_A|Activate configuration]]
+*[[Activate_Configuration_B|Activate configuration]]
 | valign="top" |
@@ Line 820: / Line 897: @@
 *[[Toolpack:Create_New_Routing_Script_B|Create new routing script]]
 *[[Import_Customized_Routing_Script_A|Import customized routing script]]
-*[[Enable_Routing_Script_A|Enable routing script]]
+*[[Enable_Routing_Script_B|Enable routing script in Gateway]]
-*[[Activate_Configuration_A|Activate configuration]]
+*[[Activate_Configuration_B|Activate configuration]]
+| valign="top" |
+*[[Toolpack:Create_New_Routing_Script_B|Create new routing script]]
+*[[Enable_Priority_Loadsharing_Routing_Script_A|Enable Priority and Load-sharing Routing script]]
+*[[Add_group_weight_Columns_in_Routes_B|Add group and weight columns in routes]]
+*[[Enable_Routing_Script_B|Enable routing script in Gateway]]
+*[[Activate_Configuration_B|Activate configuration]]
 |}
@@ Line 832: / Line 916: @@
 |-
 | valign="top" |
-*[[Toolpack:Configuring_Audio_Prompts A|Audio Prompts]]
+*[[Toolpack:Configuring_Audio_Prompts B|Audio Prompts]]
 |}
@@ Line 838: / Line 922: @@
 <br><br>
-==''Label Routing''==
+==Label Routing==
 This section assumes:
@@ Line 850: / Line 934: @@
 |-
 | valign="top" |
-*[[Adding_Label_Routing_to_any_Routing_Script|Add Label Routing to script]]
+*[[Toolpack:Adding_Label_Routing_to_any_Routing_Script_B|Add Label Routing to script]]
-*[[Create_Databse_Files A|Create Database Files]]
+*[[Toolpack:Create_Databse_Files_B|Create Database Files]]
-*[[Assign_Routing_Script_DB_Files_to_Gateway_Application A|Assign Routing/Script Files to the Gateway Application]]
+*[[Toolpack:Assign_Routing_Script_DB_Files_to_Gateway_Application_B|Assign Routing/Script Files to the Gateway Application]]
-*[[Add_Digitmap_Files A|Add the Digit Map Files to the System]]
+*[[Toolpack:Add_Digitmap_Files_B|Add the Digit Map Files to the System]]
-*[[Add_Routeset_Definition_Files A|Add the Routset Definition Files to the System]]
+*[[Toolpack:Add_Routeset_Definition_Files_B|Add the Routset Definition Files to the System]]
-*[[Assign_Definition_Digitmap_Files_per_NAP A|Assign Defintion/Digitmap Files on a per NAP Basis]]
+*[[Toolpack:Assign_Definition_Digitmap_Files_per_NAP_B|Assign Defintion/Digitmap Files on a per NAP Basis]]
-*[[Generate_Dynamic_Routes A|Generate Dynamic Routes]]
+*[[Toolpack:Generate_Dynamic_Routes_B|Generate Dynamic Routes]]
-*[[Activate_Configuration_A|Activate configuration]]
+*[[Activate_Configuration_B|Activate configuration]]
 |}
 |STYLE="vertical-align: top"|
@@ Line 864: / Line 948: @@
 |-
 | valign="top" |
-*[[Update_Digitmap_Files A|Update the Digitmap Files]]
+*[[Toolpack:Update_Digitmap_Files_B|Update the Digitmap Files]]
-*[[Update_Routeset_Definition_Files A|Update the Routeset Definition Files]]
+*[[Toolpack:Update_Routeset_Definition_Files_B|Update the Routeset Definition Files]]
-*[[Generate_Dynamic_Routes A|Generate Dynamic Routes]]
+*[[Toolpack:Generate_Dynamic_Routes_B|Generate Dynamic Routes]]
-*[[Activate_Configuration_A|Activate configuration]]
+*[[Activate_Configuration_B|Activate configuration]]
 |}
 |}
@@ Line 914: / Line 998: @@
 =Troubleshooting=
-==''Call Trace''==
+==Call Trace==
 {| cellpadding="5" border="1" class="wikitable"
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Call trace
 |-
 | valign="top" |
-*[[Toolpack:Configuring_Call_Trace A|Call trace]]
+*[[Toolpack:Configuring_Call_Trace_B|Configure call trace]]
+*[[Toolpack:Retrieving_Call_Trace_A|Retrieve call trace]]
 |}
-==''Test Call''==
+==Test Call==
 {| cellpadding="5" border="1" class="wikitable"
 ! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Test Call
@@ Line 930: / Line 1,015: @@
 |}
-==''Target Recording''==
+==Target Recording==
 {| cellpadding="5" border="1" class="wikitable"
-! width="300" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Activating a Configuration
+! width="300" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Activate Call Recording
-! width="300" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Web Portal Profile
+! width="300" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Start the Stream Server
+! width="300" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Access the Recorded Files
 |-
 | valign="top" |
 *[[Enabling_Recordings_A|Enabling the Recording of Calls]]
+| valign="top" |
+*[[How_to_Start_Stream_Server|Start Stream Server]]
 | valign="top" |
 * [[Accessing_Recording|Accessing the Recording]]
 |}
+==VoIP Ethernet Capture==
+{| cellpadding="5" border="1" class="wikitable"
+! width="250" style="background: none repeat scroll 0% 0% rgb(239, 239, 239); -moz-background-inline-policy: continuous;" | Capturing Ethernet Traffic
+|-
+| valign="top" |
+*[[VoIP_Ethernet_Capture_TMG800_A|Capturing on a TMG800]]
+*[[VoIP_Ethernet_Capture_TMG3200_A|Capturing on a TMG3200]]
+*[[VoIP_Ethernet_Capture_TMG7800_A|Capturing on a TMG7800]]
+|}
 =''Status Menus''=
@@ Line 964: / Line 1,063: @@
 *[[Toolpack:Status_Menus:Adapters_and_IP_Interfaces B|Adapters and IP Interfaces]]
 *[[Toolpack:Status_Menus:1+1|1+1]]
+*[[Toolpack:Status_Menus:N+1|N+1]]
 *[[Toolpack:Status_Menus:Hosts A|Hosts]]
 *[[Toolpack:Status_Menus:Applications A|Applications]]
@@ Line 980: / Line 1,080: @@
 *[[Toolpack:Status_Menus:ISDN A|ISDN]]
 **[[Toolpack:Status_Menus:NFAS A|NFAS]]
-*[[Toolpack:Status_Menus:CAS R2 A|CAS R2]]
+*[[Toolpack:Status_Menus:CAS R2 A|CAS]]
 *[[Toolpack:Status_Menus:SIP A|SIP]]
 *[[Toolpack:Status_Menus:Clock B|Clock]]
@@ Line 995: / Line 1,095: @@
 [[category:Toolpack]]
-[[category:Coming Soon]]

Web Portal Tutorial Guide v2.7