Web Portal Tutorial Guide v2.6

From TBwiki
(Difference between revisions)
Jump to: navigation, search
(→Status Menus)
(information are now display by feature to configure)
Line 51: Line 51:
 
|}
 
|}
  
−
=ISDN-SIP Gateway Configuration=
+
= Configuring protocol stacks =
  
−
The following tables contain a typical configuration scenario for an [[ISDN]] to [[SIP]] gateway. This type of installation allows for the transfer of information from traditional [[ISDN]] signaling to [[SIP]] protocol for [[VoIP]] applications. Please follow each step one after another as these are listed in logical order.
+
== ISDN/NFAS ==
  
 +
{| cellpadding="5" border="1" class="wikitable"
 +
|-
  
−
'''The steps are as follows:'''
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
  
−
*1) Log On and Create a New Configuration
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configure ISDN-PRI Signaling
−
*2) Allocate Physical Interfaces
+
−
*3) Configure ISDN-PRI Signaling
+
−
*4) Configure Clocking Source
+
−
*5) Configure SIP Signaling
+
−
*6) Configure Codecs and Tone Detection
+
−
*7) Configure Network Access Points (NAPs)
+
−
*8) Create Call Routing Rules
+
  
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Modify NAP profile
  
−
<b>'''IMPORTANT!'''</b> After completing the setup process, remember to '''activate the configuration''', as outlined in the [[Web_Portal_Tutorial_Guide_v2.5#General_Web_Portal_Applications|General Web Portal Applications section]].
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Network Access Points (NAPs)
 +
|-
  
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
 +
 +
| valign="top" |
 +
*[[Toolpack:Configuring_an_ISDN_Stack A|Configure an ISDN stack]]
 +
OR<br/>
 +
*[[Configure NFAS]]
 +
 +
| valign="top" |
 +
*[[Toolpack:Modify_NAP_profile|Modify profile]]
 +
 +
| valign="top" |
 +
*[[Toolpack:Allocating_an_ISDN_Network_Access_Point_(NAP) A|Allocate an ISDN NAP]]
 +
 +
|}
 +
 +
 +
 +
== CASR2 ==
 +
Toolpack v2.5 allows you to configure CAS R2 signaling stacks. The following table lists the basic steps that must be followed in order to configure CAS R2.
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Log On and Create a New Configuration
 
  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Allocate Physical Interfaces
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring a CAS R2 stack
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Modify NAP profile
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Network Access Points (NAPs)
  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configure ISDN-PRI Signaling
+
|-
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create Line Interfaces]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create Line services]]
 +
| valign="top" |
 +
*[[Toolpack:Copy variant script A|Copy variant script]]
 +
*[[Toolpack:Create CAS R2 stack A|Create CAS R2 stack]]
 +
*[[Toolpack:Setting CAS R2 BACK DIGITS variable A|Set backward digits string]]
 +
| valign="top" |
 +
*[[Toolpack:Modify_NAP_profile|Modify profile]]
 +
| valign="top" |  
 +
*[[Toolpack:Creating_a_CAS_R2_NAP A|Create a CASR2 NAP]]
  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Clocking Source
+
|}
  
 +
== SIP ==
 +
 +
{| cellpadding="5" border="1" class="wikitable"
 +
|-
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Configure IP port range
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configure SIP Signaling
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configure Codecs and Tone Detection
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Modify NAP profile
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure Network Access Points (NAPs)
 
|-
 
|-
 
| valign="top" |
 
| valign="top" |
 +
*[[Toolpack:Creating_an_IP_Port_Range A|Create an IP port range]]
  
−
| valign="top" |  
+
| valign="top" |
 +
*[[Toolpack:Creating_a_SIP_Stack A|Create a SIP stack]]
 +
*[[Toolpack:Creating_a_SIP_Transport_Server A|Create a SIP transport server]]
 +
*[[Toolpack:Creating_a_Service_Access_Point_(SAP) A|Create a service access point (SAP)]]
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Accessing_Codec_and_Tone_Detection_Profiles_and_Validating_Settings A|Access profiles and validate settings]]
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Modify_NAP_profile|Modify profile]]
  
 
| valign="top" |
 
| valign="top" |
 +
*[[Toolpack:Allocating_a_SIP_Network_Access_Point_(NAP) A|Allocate a SIP NAP]]
  
−
|-
+
|}
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure SIP Signaling
+
  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 6) <br>Configure Codecs and Tone Detection
 
  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 7) <br>Configure Network Access Points (NAPs)
+
== SS7/ISUP ==
  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 8) <br>Create Call Routing Rules
+
To configure the ISUP stack.
  
 +
=== MTP2-MTP3-ISUP ===
 +
 +
 +
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the MTP2 Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the MTP3 Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the ISUP Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Modify NAP profile
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 6) <br>Configure Network Access Points (NAPs)
 +
 +
|-
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
 +
 
| valign="top" |
 
| valign="top" |
 +
*[[Toolpack:Creating_an_MTP2_Configuration A|Create an MTP2 Configuration]]
 +
*[[Toolpack:Creating_MTP2_Links A|Create an MTP2 Link]]
 +
 +
 +
| valign="top" |
 +
*[[Toolpack:Creating_an_MTP3_Configuration A|Create an MTP3 Configuration]]
 +
*[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
 +
**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
 +
**[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 +
***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
 +
**[[Toolpack:Creating_an_MTP3_Route A|Create an MTP3 Route]]
 +
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_an_ISUP_Stack A|Create an ISUP Stack]]
 +
*[[Toolpack:Creating_an_ISUP_Network A|Create an ISUP Network]]
 +
*[[Toolpack:Creating_an_ISUP_User_Part A|Create an ISUP User Part]]
 +
*[[Toolpack:Creating_an_ISUP_Interface A|Create an ISUP Interface]]
 +
*[[Toolpack:Creating ISUP CIC Groups A|Create ISUP CIC Groups]]
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Modify_NAP_profile|Modify profile]]
  
−
| valign="top" |
 
−
|}
 
  
−
=Configuring SS7=
+
| valign="top" |
 +
*[[Toolpack:Creating_a_NAP_(SIGTRAN)_A|Create an ISUP NAP]]
  
−
The following table contains information on configuring the [[SS7]] signaling protocol.
+
|}
−
The various control layers of the [[SS7]] protocol are listed individually in each column. These layers are:
+
  
−
* [[MTP2_Layer|MTP2]] layer '''(Step 1)'''
 
−
* [[MTP3_Layer|MTP3]] layer '''(Step 2)'''
 
−
* [[ISUP]] layer '''(Step 3)'''
 
−
* [[SCCP]] layer '''(Step 4)'''
 
−
* [[TCAP]] layer '''(Step 5)'''
 
  
−
'''Follow the topics listed in each column from left to right in order to configure an SS7 protocol stack.'''
+
=== M2PA-MTP3-ISUP ===
 +
 
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Configuring the MTP2 Layer
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the MTP3 Layer
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the M2PA Layer  
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the ISUP Layer
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the MTP3 Layer
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the SCCP Layer
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the ISUP Layer
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configuring the TCAP Layer
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Modify NAP profile
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 6) <br>Configure Network Access Points (NAPs)
  
 
|-
 
|-
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
 +
 
| valign="top" |
 
| valign="top" |
 +
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating the M2PA Configuration A|Create an M2PA Configuration]]
 +
**[[Toolpack:Creating an M2PA SAP A|Create an M2PA SAP]]
 +
**[[Toolpack:Adding M2PA Links A|Add M2PA Links]]
  
 
| valign="top" |
 
| valign="top" |
 +
*[[Toolpack:Creating_an_MTP3_Configuration A|Create an MTP3 Configuration]]
 +
*[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
 +
**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
 +
**[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 +
***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
 +
**[[Toolpack:Creating_an_MTP3_Route A|Create an MTP3 Route]]
 +
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_an_ISUP_Stack A|Create an ISUP Stack]]
 +
*[[Toolpack:Creating_an_ISUP_Network A|Create an ISUP Network]]
 +
*[[Toolpack:Creating_an_ISUP_User_Part A|Create an ISUP User Part]]
 +
*[[Toolpack:Creating_an_ISUP_Interface A|Create an ISUP Interface]]
 +
*[[Toolpack:Creating ISUP CIC Groups A|Create ISUP CIC Groups]]
  
−
| valign="top" |
+
| valign="top" |  
 +
*[[Toolpack:Modify_NAP_profile|Modify profile]]
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_a_NAP_(SIGTRAN)_A|Create an ISUP NAP]]
  
 
|}
 
|}
  
−
=SIGTRAN Application Scenarios=
 
  
−
Toolpack version 2.6 enables you to configure SIGTRAN and thereby extend SS7 signalling functionality to the IP network. Toolpack enables you to configure a number of SIGTRAN applications based upon your requirements. These applications are listed below as follows: <br><br>
+
=== M3UA-ISUP ===
  
−
*[[M2PA]] system. See column '''(A)''' below. In this configuration the SS7 MTP2 layer is replaced by the SIGTRAN M2PA layer which extends MTP2 signalling functionality into the IP network. This application is typically used between a Signalling Gateway and an IP Signalling Point, or between two IP Signalling Points.
+
{| cellpadding="5" border="1" class="wikitable"
 +
|-
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the M3UA Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the ISUP Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Modify NAP profile
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure Network Access Points (NAPs)
  
 +
|-
  
−
*[[M2UA]] system. See columns '''(B)''' and '''(C)''' below. An M2UA system on a Signalling Gateway Controller interfaces with an M2UA system on a Media Gateway Controller. In this configuration, M2UA bridges the SS7 MTP2 layer of a Signalling Gateway, across an IP network, with the SS7 MTP3 layer of a Media Gateway Controller.
+
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
  
 +
| valign="top" |
 +
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
 +
*[[Toolpack:Creating an M3UA Configuration (IPSP) A|Create an M3UA Configuration]]
 +
**[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
 +
**[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
 +
**[[Toolpack:Creating an M3UA User Part A|Create an M3UA User Part]]
 +
**[[Toolpack:Creating an M3UA Peer Signalling Process (IPSP) A|Create an M3UA Peer Signalling Process]]
 +
**[[Toolpack:Creating an M3UA Peer Server A|Create an M3UA Peer Server]]
 +
**[[Toolpack:Creating an M3UA Route A|Create an M3UA Route]]
  
−
*[[IUA]] system. See column '''(D)''' below. An IUA system on a Signalling Gateway Controller interfaces with an IUA system on a Media Gateway Controller. In this configuration, IUA bridges the SS7 MTP2 layer of a Signalling Gateway, across an IP network, with the SS7 MTP3 layer of a Media Gateway Controller.
+
| valign="top" |
 +
*[[Toolpack:Creating_an_ISUP_Stack A|Create an ISUP Stack]]
 +
*[[Toolpack:Creating_an_ISUP_Network A|Create an ISUP Network]]
 +
*[[Toolpack:Creating_an_ISUP_User_Part A|Create an ISUP User Part]]
 +
*[[Toolpack:Creating_an_ISUP_Interface A|Create an ISUP Interface]]
 +
*[[Toolpack:Creating ISUP CIC Groups A|Create ISUP CIC Groups]]
  
−
+
| valign="top" |
−
*[[M3UA]] system on two IP signalling points. See column '''(E''') below. In this configuration the SS7 MTP2 and MTP3 layers are replaced entirely by the SIGTRAN M3UA layer. This application is typically used between two IP Signalling Points.
+
*[[Toolpack:Modify_NAP_profile|Modify profile]]
  
−
+
| valign="top" |
−
*[[M3UA]] system. See columns '''(F)''' and '''(G)''' below. An M3UA system on a Signalling Gateway Process interfaces with an M3UA system on an Application Server Process. In this configuration, the MTP3 links are extended across the IP network.
+
*[[Toolpack:Creating_a_NAP_(SIGTRAN)_A|Create an ISUP NAP]]
 +
 
 +
|}
 +
 
 +
== SCCP/TCAP ==
 +
 
 +
 
 +
=== MTP2-MTP3-SCCP/TCAP ===
  
−
<br> '''A SIGTRAN scenario walkthrough is provided in the table columns below, to illustrate the order that must be followed when configuring SIGTRAN.''' <br>
 
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
 +
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the MTP2 Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the MTP3 Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the SCCP Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configuring the TCAP Layer (optional)
 +
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario A) <br>Configuring an M2PA System
 
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario B) <br>Configuring an M2UA System on a Signalling Gateway
 
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario C) <br>Configuring an M2UA System on a Media Gateway Controller
 
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario D) <br>Configuring an IUA System on a Signalling Gateway
 
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario E) <br>Configuring an M3UA System on IP Signalling Points
 
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario F) <br>Configuring an M3UA System on a Signalling Gateway
 
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Scenario G) <br>Configuring an M3UA System on an Application Server
 
−
|-
 
−
|
 
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
  
−
<br>
+
| valign="top" |
 +
*[[Toolpack:Creating_an_MTP2_Configuration A|Create an MTP2 Configuration]]
 +
*[[Toolpack:Creating_MTP2_Links A|Create an MTP2 Link]]
  
−
| valign="top" |
 
  
−
| valign="top" |  
+
| valign="top" |
 +
*[[Toolpack:Creating_an_MTP3_Configuration A|Create an MTP3 Configuration]]
 +
*[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
 +
**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
 +
**[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 +
***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
 +
**[[Toolpack:Creating_an_MTP3_Route A|Create an MTP3 Route]]
  
−
<br>
 
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_an_SCCP_Stack A| Create an SCCP Stack]]
 +
*[[Toolpack:Creating_an_SCCP_Network A|Create an SCCP Network]]
 +
**[[Toolpack:Creating_an_SCCP_Userpart A|Create an SCCP Userpart]]
 +
**[[Toolpack:Creating_an_SCCP_LSAP A|Create an SCCP LSAP]]
 +
***[[Toolpack:Creating_an_SCCP_Route A|Create an SCCP Route]]
 +
****[[Toolpack:Creating_an_SCCP_SSN A|Create an SCCP SSN]]
 +
*[[Toolpack:Creating_an_SCCP_GTT_Association A|Create an SCCP GTT Association]]
 +
**[[Toolpack:Creating_an_SCCP_GTT_Address_Map A|Create an SCCP GTT Address Map]]
 +
  
 
| valign="top" |  
 
| valign="top" |  
−
 
+
*[[Toolpack:Creating_a_TCAP_Stack A|Create a TCAP Stack]]
−
| valign="top" |
+
**[[Toolpack:Creating_a_TCAP_Userpart A| Create a TCAP Userpart]]
 +
*[[Toolpack:Activating_the_Configuration A|Activating the Configuration]]
  
 
|}
 
|}
  
−
=Configuring CAS R2=
+
=== M2PA-MTP3-SCCP/TCAP ===
  
−
Toolpack v2.6 allows you to configure CAS R2 signaling stacks. The following table lists the basic steps that must be followed in order to configure CAS R2.
 
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |<br>Configuring a CAS R2 stack
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the M2PA Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the MTP3 Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the SCCP Layer
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configuring the TCAP Layer (optional)
  
 
|-
 
|-
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
 +
 
| valign="top" |
 
| valign="top" |
 +
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating the M2PA Configuration A|Create an M2PA Configuration]]
 +
**[[Toolpack:Creating an M2PA SAP A|Create an M2PA SAP]]
 +
**[[Toolpack:Adding M2PA Links A|Add M2PA Links]]
  
−
|}
+
| valign="top" |
 +
*[[Toolpack:Creating_an_MTP3_Configuration A|Create an MTP3 Configuration]]
 +
*[[Toolpack:Creating_an_MTP3_Network A|Create an MTP3 Network]]
 +
**[[Toolpack:Creating_SS7_Point_Codes A|Create an MTP3 Point Code]]
 +
**[[Toolpack:Creating_an_MTP3_Linkset A|Create an MTP3 Linkset]]
 +
***[[Toolpack:Creating_MTP3_Links A|Create MTP3 Links]]
 +
**[[Toolpack:Creating_an_MTP3_Route A|Create an MTP3 Route]]
  
−
=Configuring H.248=
 
  
−
The following table contains steps for configuring an H.248 media gateway control protocol
+
| valign="top" |
 +
*[[Toolpack:Creating_an_SCCP_Stack A| Create an SCCP Stack]]
 +
*[[Toolpack:Creating_an_SCCP_Network A|Create an SCCP Network]]
 +
**[[Toolpack:Creating_an_SCCP_Userpart A|Create an SCCP Userpart]]
 +
**[[Toolpack:Creating_an_SCCP_LSAP A|Create an SCCP LSAP]]
 +
***[[Toolpack:Creating_an_SCCP_Route A|Create an SCCP Route]]
 +
****[[Toolpack:Creating_an_SCCP_SSN A|Create an SCCP SSN]]
 +
*[[Toolpack:Creating_an_SCCP_GTT_Association A|Create an SCCP GTT Association]]
 +
**[[Toolpack:Creating_an_SCCP_GTT_Address_Map A|Create an SCCP GTT Address Map]]
  
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_TCAP_Stack A|Create a TCAP Stack]]
 +
**[[Toolpack:Creating_a_TCAP_Userpart A| Create a TCAP Userpart]]
 +
*[[Toolpack:Activating_the_Configuration A|Activating the Configuration]]
 +
 +
|}
 +
 +
 +
=== M3UA-SCCP/TCAP ===
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Add a Hardware Adapter
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Allocate Physical Interfaces
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Configuring the M3UA Layer
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Create IP Port Ranges
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Configuring the SCCP Layer
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Network Access Points (NAPs)
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configuring the TCAP Layer (optional)
  
 
|-
 
|-
−
| valign="top" |
 
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_a_Line_Interface A|Create a new line interface]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create a new line service]]
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
 +
*[[Toolpack:Creating an M3UA Configuration (IPSP) A|Create an M3UA Configuration]]
 +
**[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
 +
**[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
 +
**[[Toolpack:Creating an M3UA User Part A|Create an M3UA User Part]]
 +
**[[Toolpack:Creating an M3UA Peer Signalling Process (IPSP) A|Create an M3UA Peer Signalling Process]]
 +
**[[Toolpack:Creating an M3UA Peer Server A|Create an M3UA Peer Server]]
 +
**[[Toolpack:Creating an M3UA Route A|Create an M3UA Route]]
  
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Toolpack:Creating_an_SCCP_Stack A| Create an SCCP Stack]]
 +
*[[Toolpack:Creating_an_SCCP_Network A|Create an SCCP Network]]
 +
**[[Toolpack:Creating_an_SCCP_Userpart A|Create an SCCP Userpart]]
 +
**[[Toolpack:Creating_an_SCCP_LSAP A|Create an SCCP LSAP]]
 +
***[[Toolpack:Creating_an_SCCP_Route A|Create an SCCP Route]]
 +
****[[Toolpack:Creating_an_SCCP_SSN A|Create an SCCP SSN]]
 +
*[[Toolpack:Creating_an_SCCP_GTT_Association A|Create an SCCP GTT Association]]
 +
**[[Toolpack:Creating_an_SCCP_GTT_Address_Map A|Create an SCCP GTT Address Map]]
  
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_TCAP_Stack A|Create a TCAP Stack]]
 +
**[[Toolpack:Creating_a_TCAP_Userpart A| Create a TCAP Userpart]]
 +
*[[Toolpack:Activating_the_Configuration A|Activating the Configuration]]
  
 +
|}
 +
 +
== H.248 ==
 +
 +
If the Tmedia is used to forward signalling messages to the SSW, you will require to configure M2UA, M3UA or IUA before configuring H.248.
 +
 +
If the Tmedia is used to connect media only, then you can go straight to [[Web_Portal_Tutorial_Guide_v2.6#H.248|H.248 Configuration]]
 +
 +
=== M2UA ===
 +
 +
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure the Media Gateway for H.248 mode
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Create Line Interfaces
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 6) <br>Create an H.248 Configuration
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Create MTP2 links
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 7) <br>Add a New Media Gateway Controller
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Create M2UA configuration
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 8) <br>Associate NAPs with the H.248 Configuration
+
 
   
 
   
 +
|-
  
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create line interfaces]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create line services]]
  
−
|-
 
 
| valign="top" |  
 
| valign="top" |  
  
−
| valign="top" |
+
*[[Toolpack:Creating an MTP2 Configuration A|Create an MTP2 Configuration]]
 +
**[[Toolpack:Creating MTP2 Links A|Create MTP2 Links]]
  
 
| valign="top" |  
 
| valign="top" |  
  
−
| valign="top" |
+
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating the M2UA Configuration A|Create an M2UA Configuration]]
 +
**[[Toolpack:Creating an M2UA SAP A|Create an M2UA SAP]]
 +
**[[Toolpack:Creating an M2UA Cluster A|Create an M2UA Cluster]]
 +
**[[Toolpack:Creating M2UA Links A|Create M2UA Links]]
 +
**[[Toolpack:Creating M2UA Peers A|Create M2UA Peers]]
  
−
|-
+
|}
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 9) <br>Select Timeslots for TDM Terminations
+
  
 +
 +
=== M3UA ===
 +
 +
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
| valign="top" |
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Create Line Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Create MTP2 links
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Create MTP3 configuration
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Create M3UA configuration
 +
|-
 +
 
 +
| valign="top" |  
 +
*[[Toolpack:Creating_a_Line_Interface A|Create line interfaces]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create line services]]
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Creating an MTP2 Configuration A|Create an MTP2 Configuration]]
 +
*[[Toolpack:Creating MTP2 Links A|Create MTP2 Links]]
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Creating SS7 Point Codes A|Create SS7 Point Codes]]
 +
*[[Toolpack:Creating an MTP3 Configuration A|Create an MTP3 Configuration]]
 +
**[[Toolpack:Creating an MTP3 Network A|Create an MTP3 Network]]
 +
**[[Toolpack:Creating an MTP3 Linkset A|Create an MTP3 Linkset]]
 +
**[[Toolpack:Creating MTP3 Links (M3UA) A|Create MTP3 Links]]
 +
**[[Toolpack:Creating an MTP3 Route A|Create an MTP3 Route]]
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating an M3UA Configuration (SGP) A|Create an M3UA Configuration]]
 +
**[[Toolpack:Creating an M3UA SAP A|Create an M3UA SAP]]
 +
**[[Toolpack:Creating an M3UA Network A|Create an M3UA Network]]
 +
**[[Toolpack:Creating an M3UA User Part A|Create an M3UA User Part]]
 +
**[[Toolpack:Creating an M3UA Peer Signalling Process (SGP) A|Create an M3UA Peer Signalling Process]]
 +
**[[Toolpack:Creating an M3UA Peer Server A|Create an M3UA Peer Server]]
 +
**[[Toolpack:Creating an M3UA Route (SGP) A|Create an M3UA Route]]<br>
 +
 
 
|}
 
|}
  
−
=Configuring an H.323 to SIP Converter=
+
=== IUA ===
  
−
The following table contains steps for configuring NAPs that wil allow an interface between the web portal and a YATE H.323 to SIP signal converter:
+
{| cellpadding="5" border="1" class="wikitable"
 +
|-
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Create Line Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Create M2UA Configuration
 +
 +
|-
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Creating a Line Interface A|Create Line Interfaces]]
 +
*[[Toolpack:Creating a Line Service A|Create Line services]]
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Creating the SCTP Configuration A|Edit the SCTP Configuration]]
 +
*[[Toolpack:Creating the IUA Configuration A|Create an IUA Configuration]]
 +
**[[Toolpack:Creating an IUA SAP A|Create an IUA SAP]]
 +
**[[Toolpack:Creating an IUA Cluster A|Create an IUA Cluster]]
 +
**[[Toolpack:Creating IUA Links A|Create IUA Links]]
 +
**[[Toolpack:Creating IUA Peers A|Create IUA Peers]]
 +
 
 +
|}
 +
 
 +
=== H.248 ===
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
 
|-
 
|-
−
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | <br> Configuring an H.323 to SIP Signal Converter
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 1) <br>Allocate Physical Interfaces
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 2) <br>Create IP Port Ranges
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 3) <br>Modify NAP profile
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 4) <br>Configure Network Access Points (NAPs)
 +
 +
|-
  
 +
| valign="top" |
 +
*[[Toolpack:Creating_a_Line_Interface A|Create line interfaces]]
 +
*[[Toolpack:Creating_a_Line_Service A|Create line services]]
 +
 +
| valign="top" |
 +
*[[Toolpack:Creating_an_IP_Port_Range A|Create IP port ranges]]
 +
| valign="top" |
 +
*[[Toolpack:Modify_NAP_profile|Modify profile]]
 +
 +
| valign="top" |
 +
*[[Toolpack:Allocating_a_VoIP_Network_Access_Point_(NAP) A|Allocate a VoIP NAP]]
 +
*[[Toolpack:Allocating_a_TDM_Network_Access_Point_(NAP) A|Allocate a TDM NAP]]
 
|-
 
|-
−
| valign="top" |
+
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 5) <br>Configure Media Gateway for H.248 mode
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 6) <br>Add a New Media Gateway Controller
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" | (Step 7) <br>Associate NAPs Resources to H.248 Configuration
 +
 
 +
 
 +
 
 +
|-
 +
 
 +
| valign="top" |  
 +
*[[Toolpack:Configure the Media_Gateway_for_H248_Mode A|Configure the Media Gateway for H.248 mode]]
 +
*[[Toolpack:Creating_an_H.248_Configuration A|Create a new H.248 configuration]]
 +
| valign="top" |
 +
*[[Toolpack:Adding_a_Media_Gateway_Controller_(MGC) A|Add a new media gateway controller (MGC)]]
 +
| valign="top" |
 +
*[[Toolpack:Associating_NAPs_with_an_H.248_Configuration A|Associate the NAPs with the H.248 configuration]]
 +
*[[Toolpack:Selecting_Timeslots_for_TDM_Interfaces A|Select timeslots for the TDM interfaces]]
  
 
|}
 
|}
  
−
=Configuring SNMP=
 
  
−
To use the Simple Network Management Protocol (SNMP)on your machine, you must first configure the '''tbSnmpAgent'''.
+
= CDR =
−
<br/>The '''tbSnmpAgent''' is a software application that interfaces between the TMedia system hardware and the [http://www.net-snmp.org NetSnmp] implementation of the SNMP that is supported by TelcoBridges.
+
−
By default, tbSnmpAgent is '''disabled'''. In order to use the SNMP protocol to monitor and manage your hardware, complete the following tasks:
+
−
<br/>
+
−
* Activate the tbSnmpAgent
+
−
* Configure the tbSnmpAgent as required
+
−
<br/>
+
−
These tasks can be completed using the [[Web Portal]]:
+
−
<br/>
+
−
#[[Activating tbSnmpAgent|Activate tbSnmpAgent]]
+
−
#[[Configuring tbSnmpAgent|Configure tbSNMPAGENT to suit your needs]]
+
−
<br/>
+
−
Once these tasks are completed, your TMedia platform is ready to expose system variables for polling with the Simple Network management Protocol (SNMP).
+
  
−
=Configuring RADIUS=
+
{| cellpadding="5" border="1" class="wikitable"
 +
|-
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |Text CDR
 +
! width="200" style="background: rgb(239, 239, 239) none repeat scroll 0% 0%; -moz-background-clip: border; -moz-background-origin: padding; -moz-background-inline-policy: continuous;" |RADIUS
 +
|-
  
−
Toolpack v2.6 can send accounting requests containing CDR data to a remote RADIUS server. In order to do so, refer to the [[Toolpack:Configuring_RADIUS A|Configuring RADIUS]] page.
+
| valign="top" |
 +
*[[Text_cdr|Text CDR]]
 +
 
 +
| valign="top" |
 +
*[[Toolpack:Configuring_RADIUS A|Configuring RADIUS]]
 +
 
 +
|}
  
−
=Configuring Fax=
+
= Fax =
  
 
{| cellpadding="5" border="1" class="wikitable"
 
{| cellpadding="5" border="1" class="wikitable"
Line 293: Line 594:
 
|-
 
|-
 
| valign="top" |
 
| valign="top" |
 +
*[[Configure_Fax_Relay_A|Configure Fax Relay]]
 +
*[[Configure_Fax_Passthrough_A|Configure Fax Passthrough]]
 
| valign="top" |  
 
| valign="top" |  
 +
*[[Configure_Fax_Relay_A|Configure Fax Relay]]
 +
*[[Configure_Fax_T38_A|Configure Fax T38]]
 
|}
 
|}
  

Revision as of 14:53, 25 September 2012

Contents

Introduction

This guide is designed to provide users with a scenario-based approach to installing Tmedia and Tdev systems, using the Web Portal configuration tool. This means that users must first go through the steps that are general to all installations, and subsequently follow the instructions that are specific to their particular application scenario (this corresponds to the type of service, and hardware system being set up).


Prerequisites

This document assumes that the Tmedia or Tdev devices are installed as described in their Quick Reference Guides, and in the case of the Tmedia system communication has been established with the control network.

(Note: Tmedia devices are shipped with the Tmedia Web Portal pre-installed, while Tdev devices require that Toolpack be installed as described in the TMP6400 Installation Guide.)

Furthermore, in the case of a Tdev device and the initial configuration of the Toolpack application server, the following will have been provided:

  • The Tdev device to which the Web Portal will first connect.
  • The Tdev device will have been pre-configured with its physical TDM interface.
  • The serial number of the Tdev device will have been entered into the configuration file.
  • The application software for the Tdev device will have been pre-installed on the Toolpack application server, as described in the TMP6400 Installation Guide.

This document also assumes familiarity with topics, such as ISDN signaling, SIP signaling, SS7, CAS R2 signaling, and SIGTRAN signaling.


Key Concepts

  • System: A system is defined as the complete solution that is designed for a network. If a system solution is comprised of 4 TMP6400’s and a TMS1600, then the combination of these TelcoBridges devices is termed a system.
  • Hardware: Each TelcoBridges devices, whether it is a TMP6400, TMG3200, or TMS1600 is referred to as a hardware device or hardware adapter.
  • Line Interface: The physical TDM module installed on the TelcoBridges device is referred to as a line interface.


General Web Portal Applications

IMPORTANT! The Topics covered in the following table are common to all TMedia installations. Therefore, this section should be consulted before moving on to any other.


Topics covered here:

  • The basic knowledge needed to properly navigate through the Web Portal (A).
  • The fundamentals of user account management and permission masks (B).
  • The initial steps required for first starting the Web Portal, and verifying that it is functioning properly (C).
  • The process involved in backing up your database for the first time (D).
  • The process involved in first configuring your IP interfaces (E).


(Topic A)
Web Portal Basics 		(Topic B)
Log-on and User Access Levels 		(Topic C)
Application Start-up and Verification 		(Topic D)
Database Backup


Configuring protocol stacks

ISDN/NFAS

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configure ISDN-PRI Signaling 		(Step 3)
Modify NAP profile 		(Step 4)
Configure Network Access Points (NAPs)

OR


CASR2

Toolpack v2.5 allows you to configure CAS R2 signaling stacks. The following table lists the basic steps that must be followed in order to configure CAS R2.

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring a CAS R2 stack 		(Step 3)
Modify NAP profile 		(Step 4)
Configure Network Access Points (NAPs)

SIP

(Step 1)
Configure IP port range 		(Step 2)
Configure SIP Signaling 		(Step 3)
Configure Codecs and Tone Detection 		(Step 4)
Modify NAP profile 		(Step 5)
Configure Network Access Points (NAPs)


SS7/ISUP

To configure the ISUP stack.

MTP2-MTP3-ISUP

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring the MTP2 Layer 		(Step 3)
Configuring the MTP3 Layer 		(Step 4)
Configuring the ISUP Layer 		(Step 5)
Modify NAP profile 		(Step 6)
Configure Network Access Points (NAPs)





M2PA-MTP3-ISUP

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring the M2PA Layer 		(Step 3)
Configuring the MTP3 Layer 		(Step 4)
Configuring the ISUP Layer 		(Step 5)
Modify NAP profile 		(Step 6)
Configure Network Access Points (NAPs)



M3UA-ISUP

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring the M3UA Layer 		(Step 3)
Configuring the ISUP Layer 		(Step 4)
Modify NAP profile 		(Step 5)
Configure Network Access Points (NAPs)

SCCP/TCAP

MTP2-MTP3-SCCP/TCAP

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring the MTP2 Layer 		(Step 3)
Configuring the MTP3 Layer 		(Step 4)
Configuring the SCCP Layer 		(Step 5)
Configuring the TCAP Layer (optional)




M2PA-MTP3-SCCP/TCAP

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring the M2PA Layer 		(Step 3)
Configuring the MTP3 Layer 		(Step 4)
Configuring the SCCP Layer 		(Step 5)
Configuring the TCAP Layer (optional)



M3UA-SCCP/TCAP

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Configuring the M3UA Layer 		(Step 3)
Configuring the SCCP Layer 		(Step 4)
Configuring the TCAP Layer (optional)

H.248

If the Tmedia is used to forward signalling messages to the SSW, you will require to configure M2UA, M3UA or IUA before configuring H.248.

If the Tmedia is used to connect media only, then you can go straight to H.248 Configuration

M2UA

(Step 1)
Create Line Interfaces 		(Step 2)
Create MTP2 links 		(Step 3)
Create M2UA configuration


M3UA

(Step 1)
Create Line Interfaces 		(Step 2)
Create MTP2 links 		(Step 3)
Create MTP3 configuration 		(Step 4)
Create M3UA configuration

IUA

(Step 1)
Create Line Interfaces 		(Step 2)
Create M2UA Configuration

H.248

(Step 1)
Allocate Physical Interfaces 		(Step 2)
Create IP Port Ranges 		(Step 3)
Modify NAP profile 		(Step 4)
Configure Network Access Points (NAPs)
(Step 5)
Configure Media Gateway for H.248 mode 		(Step 6)
Add a New Media Gateway Controller 		(Step 7)
Associate NAPs Resources to H.248 Configuration



CDR

Text CDR RADIUS

Fax

FAX passthrough FAX T.38


Configuring Routing script

TelcoBridges provides a wide variety of routing script examples which customers can apply directly in their web configuration according to their needs by following just a few simple steps. Please select one of the following examples according to your needs. You may modify it when necessary.


*Flexible NOA: Remap the Calling/Called NOA flexibly based on the routes. It should cover most of the NOA requests since the routes include the calling/called remapping as well.

*Prefix NOA: Remapp Calling/Called NOA according to the prefix of the calling/called number, manipulate calling/called number. For calling number, if it is a privacy call, use the number in P-Asserted-Identity line or Remote-Party-ID line as the calling number to remap the NOA and do the manipulation.

Flexible NOA Prefix NOA

Status Menus

The Web Portal configuration tool will guide you through a number of status menus, each of which indicate the current state of a certain hardware service (assuming said service has been configured). The following table contains the general conventions of the Web Portal's display (A), as well as a variety of specific status menus (B).


(A)
Menus Overview 		(B)
Individual Menu Descriptions
Retrieved from "https://docs.telcobridges.com/mediawiki/index.php?title=Web_Portal_Tutorial_Guide_v2.6&oldid=12043"
Personal tools