Web Portal Tutorial Guide v2.2

Revision as of 10:57, 4 August 2010

This guide describes the setup and configuration of a Tdev system consisting of TMP6400 devices and TMS1600 switches, or a Tmedia TMG3200 system using the Web Portal component of Toolpack.

Please note that most of the information panels of the Web Portal provide you with configuration and status information. Other than the last section in this guide (i.e., status menus), all sections are designed to show you how to configure your Tmedia or Tdev system; therefore, they do not describe how to navigate and interpret system status. To learn about system status information, refer to the final section of this guide.

Finally, it is recommended that you follow the order of the tasks here in order to successfully configure a Tmedia or Tdev system, particularly if you want to configure signaling stacks or line interfaces.

Before you begin

This document assumes that the Tmedia or Tdev devices are installed as described in their Quick Reference Guides and that communication has been established with the control network.

(Note: The TMG3200 is shipped with the Tmedia Web Portal preinstalled, while the TMP6400 requires that Toolpack be installed as described in the TMP6400 Installation Guide.)

Furthermore, in the case of the TMP6400 and the initial configuration of the Toolpack application server, the following will have been provided:

• The TMP6400 to which the Web Portal will first connect.
• The TMP6400 will have been pre-configured with its physical TDM interface.
• The serial number of the TMP6400 will have been entered into the configuration file.
• The application software for the TMP6400 devices will have been pre-installed on the Toolpack application server, as described in the TMP6400 Installation Guide.

This document also assumes familiarity with topics, such as ISDN signaling, SIP signaling, and SS7 signaling.

Key concepts

• System: A system is defined as the complete solution that is designed for a network. If a system solution is comprised of 4 TMP6400’s and a TMS1600, then the combination of these TelcoBridges devices is termed a system.
• Hardware: Each TelcoBridges devices, whether it is a TMP6400, TMG3200, or TMS1600 is referred to as a hardware device or hardware adapter.
• Line Interface: The physical TDM module installed on the TelcoBridges device is referred to as a line interface.

Web Portal Tutorial Guide

Introduction

• Web Portal
• Navigating the Web Portal
• Typographic conventions
• Graphical Conventions
• Configuring Your Tmedia System

Log On and User Access Levels

• Logging On
• User Access
  • Viewing the User List
  • Creating a New User
  • Deleting a User
  • Logging Off

Application Startup and Verification

• Viewing the List of Installed Applications
• Starting an Application
• Verifying that an Application is Operating
  • Verifying the Application Path
• Activating the Configuration
  • Verifying status

Tmedia / Tdev Units

• Listing Hardware
• Adding a TMP6400
• Switching Between Tmedia/Tdev Unit Hardware Configurations
  • Verifying Status

TMS Network Switch

• About the TMS1600
• Adding a TMS1600
• Configuring a TMS Network System
  • Verifying Status

Line Interfaces

• TDM Module Options
  • Verifying status of TDM Lines
  • Verifying status of Adapters and IP Interfaces
• T1, E1, and J1 interfaces
  • Adding a E1/T1/J1 Line Interface
  • Configuring E1/T1/J1 Line Services
    • Activating the Configuration
• DS3 interfaces
  • Adding a DS3 Line Interface
  • Configuring DS3 Line Services
    • Activating the Configuration
• SONET/SDH interfaces
  • Creating a Primary Line SONET/SDH Interface
  • Creating a Protection Line SONET/SDH Interface
  • Verifying the Status of the OC3 Line Interface
  • Configuring SONET/SDH Line Services
    • Activating the Configuration

BITS

• BITS Ports
• Creating BITS Ports as a Clocking Source
  • Verifying Status

Clocking

• Clocking Sources
• Verifying the Current Clocking Source
• Creating a Clocking Source
  • Verifying Status

ISDN Signaling

• ISDN
• Configuring the ISDN Signaling Stack
  • Verifying status

SIP Signaling

• SIP
• Creating a SIP Signaling Stack
• Creating a Transport Server
• Configuring DNS Parameters
• Creating a SAP
  • Activating the Configuration
  • Verifying status

SS7 Signaling

• SS7
• MTP2 Layer
  • Create an MTP2 Configuration
  • Create an MTP2 Link
    • Verifying Status
• MTP3 Layer
  • Create an MTP3 Configuration
  • Create an MTP3 Network
    • Create an MTP3 Point Code
    • Create an MTP3 Linkset
    • Create an MTP3 Route
    • Verifying Status
• ISUP
  • Create an ISUP Stack
  • Create an ISUP Network
  • Create an ISUP User Part
  • Create an ISUP Interface
    • Verifying Status
• Activating the Configuration

SIP Profiles

• SIP Profiles
• Creating a SIP Profile
• Activating the Configuration

Network Access Points

• Creating a NAP
  • Verifying status

Gateway Application

• TMG3200
• Creating a TMG3200 Gateway Configuration
• Creating Called Number Routes

Status Menus

• Tmedia Status Menus
  • Navigation
  • Status Screen Conventions
• Individual Menu Descriptions
  • System
  • Adapters and IP Interfaces
  • Hosts
  • Applications
  • TDM Lines
  • SS7 MTP2
  • SS7 MTP3
  • SS7 ISUP
  • ISDN
  • SIP
  • NAP
  • CDR

References

• Web Portal Tutorial Guide (single document)
• Supported ISDN standards and variants

Other reading

For further information, refer to the following reading list:

• TMedia System Architecture Overview for Developers of VoIP and TDM Solutions
• TB640 User's Guide
• TelcoBridges SS7 User's Guide
• SIP User’s Guide