Web Portal Tutorial Guide v2.4

Introduction

The articles in this page describe the setup and configuration of a Tdev system consisting of TMP6400 devices and TMS1600 switches, or a Tmedia TMG3200 system using the Web Portal component of Toolpack.

Please note that most of the information panels of the Web Portal provide you with configuration and status information. All the Web Portal article in this page are designed to show you how to configure your Tmedia or Tdev system; therefore, they do not describe how to navigate and interpret system status. To learn about system status information, refer to Section on Interpreting Status Menus.

Finally, it is recommended that you follow the order of the tasks listed on this page to successfully configure a Tmedia or Tdev system, particularly if you want to configure signaling stacks or line interfaces.

Before you begin

This document assumes that the Tmedia or Tdev devices are installed as described in their Quick Reference Guides and that communication has been established with the control network.

(Note: The TMG3200 is shipped with the Tmedia Web Portal preinstalled, while the TMP6400 requires that Toolpack be installed as described in the TMP6400 Installation Guide.)

Furthermore, in the case of the TMP6400 and the initial configuration of the Toolpack application server, the following will have been provided:

• The TMP6400 to which the Web Portal will first connect.
• The TMP6400 will have been pre-configured with its physical TDM interface.
• The serial number of the TMP6400 will have been entered into the configuration file.
• The application software for the TMP6400 devices will have been pre-installed on the Toolpack application server, as described in the TMP6400 Installation Guide.

This document also assumes familiarity with topics, such as ISDN signaling, SIP signaling, and SS7 signaling.

Key concepts

• System: A system is defined as the complete solution that is designed for a network. If a system solution is comprised of 4 TMP6400’s and a TMS1600, then the combination of these TelcoBridges devices is termed a system.
• Hardware: The TMP6400, TMG3200, or TMS1600 are referred to as a hardware device or hardware adapter.
• Line Interface: The physical TDM module installed on the TelcoBridges device is referred to as a line interface.

SIGTRAN Configuration Scenarios

Toolpack version 2.4 enables you to configure SIGTRAN and maintain control over SS7 signalling in the IP network. A number of SIGTRAN configurations are possible based upon the apllication. They are listed below as follows:

• M2PA system: In this configuration the SS7 network extends between two signalling gateways.
• M2UA system on a signalling gateway: In this configuration...
• M2UA system on a media gateway controller: In this configuration...
• M3UA on an IP signalling point: In this configuration...
• M3UA on a signalling gatweway: In this configuration...
• M3UA on an application server: In this configuration...

A walkthrough is provide for each SIGTRAN scenario, in the table below, to illustrate the order that must be followed when configuring the SIGTRAN protocol.

Configuring an M2PA System	Configuring an M2UA on a Signalling Gateway	Configuring an M2UA on a Media Gateway Controller	Configuring an M3UA on an IP Signalling Point	Configuring an M3UA on a Signalling Gateway	Configuring an M3UA on an Application Server
INTRO	INTRO	INTRO	INTRO	INTRO	INTRO
Adding an Adapter Create Line Interfaces Create Line services Edit the SCTP Configuration Create an M2PA Configuration Create an M2PA SAP Add M2PA Links Edit Destination Addresses Create an MTP3 Configuration Configure Point Codes Create an MTP3 Stack Create an MTP3 Network Create a Linkset Create MTP3 Routes Assign MTP3 Routes Configure ISUP Create an ISUP Stack Create an ISUP Network Configure an ISUP User Part Configure an ISUP I/F Create ISUP CIC Groups Create a NAP	Adding an Adapter Create Line Interfaces Create Line services Create an MTP2 Configuration Create MTP2 Links Create an M2UA Configuration Create an M2UA Cluster Create M2UA Links Create M2UA Peers	Adding an Adapter Edit the SCTP Configuration Create an M2UA Create an M2UA SAP Create an M2UA Cluster Create M2UA Peers Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route Create an ISUP Stack Create an ISUP Network Configure an ISUP User Part Configure an ISUP I/F Create ISUP CIC Groups Create a NAP	Adding an Adapter Edit the SCTP Configuration Create SS7 Point Codes Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create M3UA Routes Create an ISUP Stack Create an ISUP Network Configure an ISUP User Part Configure an ISUP I/F Create ISUP CIC Groups Create a NAP	Adding an Adapter Create Line Interfaces Create an MTP2 Configuration Create MTP2 Links Create an SCTP Configuration Create SS7 Point Codes Create an MTP3 Configuration Create an MTP3 Network Create an MTP3 Linkset Create MTP3 Links Create an MTP3 Route Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create M3UA Routes	Adding an Adapter Edit the SCTP Configuration Create SS7 Point Codes Create an M3UA Configuration Create an M3UA SAP Create an M3UA Network Create an M3UA User Part Create an M3UA Peer Signalling Process Create an M3UA Peer Server Create M3UA Routes Create an ISUP Configuration

Other reading

For further information, refer to the following reading list:

• TMedia System Architecture Overview for Developers of VoIP and TDM Solutions
• TB640 User's Guide
• TelcoBridges SS7 User's Guide
• SIGTRAN
• SIP User’s Guide